Question about 2003 GMC Yukon

1 Answer

How to remove driver seat in 2003 yukon - 2003 GMC Yukon

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 512 Answers

You have four bolts one at each corner, take them out, then unplug wire harness. Seat will come out.

Posted on Jul 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to remove driver seat cushion yukon xl 2001


Well I believe that only upholstery can fix that but the whole seat comes off. What seems to be the problem? It would be cheaper, only if your budget is tight, if you get another one from a pick a part near you.

Jun 27, 2014 | 2001 GMC Yukon XL

1 Answer

2003 Yukon Denali.driver car seat heater don't wonk


The seat heater grid is likely shorted.

Feb 22, 2014 | 2003 GMC Yukon XL

1 Answer

Jus t purchased a used 2003 yukon xl and trying to find out how to fold the 2nd row seat down cannot find a lever on the one side


The passenger side 2nd row release lever is at the lower right corner. On the driver side, there is no release lever, just a pull ******** the center of the seat, that sometimes falls between the seat.

Aug 26, 2011 | 2003 GMC Yukon XL

1 Answer

How do i let down the rear seats in 2003 gmc yukon xL


FYI- I'm taking a shot at this one based on my 2003 Montana so take it for what it's worth.
My van seats have a very small level on the drivers side of each seat. Pushing the lever down allows the seats to fold down while pulling the lever up allows them to recline. There is also a small ******** the back side of each seat which when pulled allows them to be folded down.
Hopefully your 2003 Yukon seats are similar to my 2003 Montana seats and this will work for you

Feb 02, 2011 | 2003 GMC Yukon XL

1 Answer

On my 2003 yukon I have no heated front seats working and no power seat for the drivers side.


Look in the fuse box on the driver's side of the vehicle on the outboard side of the dash under the triangular cover which snaps off and on. This panel is not visible when the door is closed. If you have your owner's manual, look on page 5-104. This is where the fuses and relay/circuit breaker descriptions, layout, and specifications begin. This section runs to page 5-111.
You are going to check fuse number IGN3, a red plastic, stab-in miniature 10Amp fuse. It has an "S"-shaped element visible through the side of the fuse body. If the element is broken or burned, replace this fuse. DO NOT use a replacement fuse of ANY other rating; use an identical 10Amp fuse ONLY.
You are also going to look for the "Center Instrument Panel Fuse Block," located under the instrument panel, to the left of the steering column. You are going to check the device labeled "30A CB Seat." This is driver and passenger seat module circuit breaker. This circuit breaker is an automatic resetting device, replacement is necessary only if there is no other problem, and it will not reset.
If only the driver seat is affect, the problem is not the CB Seat; check the wire harness and connector under the seat. There is almost no clearance under the seat, and it may needs be removed to check this. There are four 14mm or 15mm bolts, one at each outboard corner of the seat, the front ones under snap-on plastic covers, which anchor the seat to the vehicle. These bolts are installed with an anti-seize anchoring compound which make them difficult to remove, but aside from elbow grease, there is no other trick to removing them.
Good luck, and if I have helped you, please remember to comment/vote.

Feb 21, 2010 | 2003 GMC Sierra 1500

1 Answer

Need to remove 2004 Yukon drivers seat. how do


there are plastic covers over the front bolts that hold the seat to the floor remove the screws the hold these covers on then remove the two front bolts under these covers then move the seat all the way forward and you should be able to see the two bolts that hold the rear of the seat to the floor pan there could be covers on these to remove the bolts and then tip the seat forward and unplug the wire connector for the power seat(if it has this option).hope this helped

Jan 01, 2010 | 2004 GMC Yukon

1 Answer

Does the back seat of the yukon come out? I can


by the picture it looks like a 2000 to 2004 yukon.
im assuming you are talking about the 3rd row seat?
if so yes it comes out, the instructions are numbered on the seat, 1, 2 3.
if you are talking about the rear seat, inline with the rear doors, they do not come out, only fold down

Jul 21, 2009 | 2003 GMC Yukon XL

1 Answer

Fuel filter


It is located underneath the car on driver side, nearly under the driver seat. Follow the fuel pipe coming from the fuel tank.

Jul 18, 2008 | 2003 GMC Yukon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

200 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...