Question about 2003 Chrysler Town & Country

1 Answer

MY TURN SIGNAL QUIT WORKING IS THERE A FLASHER

MY TURN SIGNALS QUIT WORKING IS THERE A FLASHER THAT CAN BE REPLACED AND WE CAN'T FIND A FUSE BOX FOR THE SIGNALS INSIDE THE CAR THERE IS ONLY 1 FUSE BOX NEXT TO THE BATTERY AND SAYS NOTHING ABOUT TURN SIGNALS. IT IS A CHRYSLER TOWN & COUNTRY 2002 AND I HAVE READ THE MANUEL AND STILL NOTHING

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Chrysler Master
  • 1,779 Answers

My service manual states that the '02 T+C has a combination turn signal/hazard flasher/daytime running lights module which is located on the junction block, adjacent to and left of the steering column. To access it, you must remove the steering column lower cover and knee pad panel. There is also a fuse for turn signal/hazard flasher. If none of them work, check the fuse 1st.

Posted on Jul 18, 2009

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: CHRYSLER town and country mini van turn signal/flasher

I have a 2005 Chrysler T&C. The turn signal would not work at all or activate incorrect side. The switch is easy to remove as described by dukecityman.

Once the switch is of, it has four screws holding it together.I took this apart to find that there was a circuit-board which was contaminated with dirt. wiped it of, put it back together, working fine.

If you take it apart use caution. there are parts on the "top" which will fall out. ( they go right back in) The circuit-board is on the "bottom" half. You really only need to take this part off. (less moving parts)

Your going to replace it anyway, whats the harm?

Posted on Jan 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1985 dodge w150 5.2. The heater will not blow its not making noise or anything. Today the turn signals quit working, i have flashers but no turn signal any suggestion


Turn signals work off a separate flasher. they still did in my 90 Bronco and brother's 88 Ramcharger. Flasher relays are usually on or near the fuse box.
Check blower fuse(in fuse box). check the resistor near plug for blower(if charred looking, replace). Check blower by supplying battery voltage to motor(if it spins, it's good)

Nov 09, 2012 | Cars & Trucks

1 Answer

Directional signal


Replace the flasher module is what I'd do.
Turn signal flasher location Remove panel covering fuse box, next remove the screw holding the heater duct work extension, with the duct work removed you can reach the flasher box cover by reaching up under the dash, remove cover from the box, then remove the flasher, the heavy duty replacement flasher is "taller" and the cover will not fit over it, reverse to close

Oct 05, 2012 | 1999 Ford Expedition

3 Answers

Turn signals quit working on my 99 lincoln town car! Everything else works but the blinkers! Fuses and bulbs ok! Thank you!


under the dash is a blinker solenoid. it constantly clicks when the turn signals are on. could be bad. Does the four way hazards work? if they do then it will be your turn signal switch (the handle you use to turn on the turn signals.) I've been a mechanic for 10 yrs. Hope this helps

Feb 22, 2011 | 1999 Lincoln Town Car

2 Answers

2006 Saturn Vue turn signals and flashers have quit working.


the switch is most likely faulty. You can also check any wiring with a voltmeter

Oct 02, 2009 | 2006 Saturn Vue

2 Answers

No turn signals but flashers work


There a two modules 1 for the turn signals and 1 for the flashers. Look under your dash around the steering wheel and fuse box area for one that is in the wiring harness.

May 31, 2009 | 1991 Ford Ranger Supercab

1 Answer

Turn signals and emergency flashers quit working.


check and replace the flasher unit if necessary, sometimes located in the fuse box area, sometimes under the dash near the steering column

May 18, 2009 | 1997 Ford Taurus

1 Answer

1978 Oldsmobile Cutlass Salon - Turn signals quit working


There is a flasher unit that could be bad.It is quite inexpensive and should be located in the area of the fuse box inside the car.There are actually 2 of them,one for the turn signals,and one for the emergency or 4 way flashers.Both should be round,and silver in color.

Jul 13, 2008 | 1985 Oldsmobile Cutlass Salon

Not finding what you are looking for?
2003 Chrysler Town & Country Logo

1,065 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...