Question about 2007 Volkswagen GTI

1 Answer

How do I reset the MIL to VW Passat 04, now that problem is fixed

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 322 Answers

You will need a scan tool in order to do this.

Posted on Jul 18, 2009

  • Juan Carlos Rosario Zayas

    You will need a scan tool in order to do this.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Inertia switch on 04 VW Passat


All these switches I have found are on the passenger side. Either in the trunk or behind the kick panel on the passenger side. Rarely do these go bad.. And they only need reset if you have a front end accident. If you are not getting fuel check the fuses and or the fuel pressure.

Nov 09, 2014 | 2004 Volkswagen Passat

1 Answer

My MIL light came on for my VW 2004 Passat and I had the code read at Autozone. The code was "system 2 lean; bank one" what does that mean?


It indicated the oxygen sensor at the bank one is reading wrongly or detecting the fault. It must be because the oxygen sensor itself has failed.

Jan 10, 2011 | 2004 Volkswagen Passat

2 Answers

Intermitent AC, 04 Passat, blower works but no cold air


possibly gas pressure to low or pressure switch on aircon condensor faulty.

May 17, 2010 | 1999 Volkswagen Passat

1 Answer

04 vw passat,1.8l.changed rear o2 sensor,now engine stumbles,is there a reset sequence?


remove the battery for half an hour, then reconnect it and the ecu should reset. After turning on ignition wait till all clicking and whirring stops before starting it, and check you havent dislodged the airflow meter connector on the airfilter when you did the o2 sensor, as this, or an intake air leak, is more likely to cause a stumble than the o2 sensor.

Jan 10, 2010 | 2004 Volkswagen Passat

1 Answer

99 vw passat, when running, MIL lite, on car vibrates- shakes


no flashing light and rough shaking will be part of spark plug but also a very bad miss fire. I am going to guess that your engine is a 1.8t if so you have 4 coils that sit on top of your spark plugs that most likely are arcing you will need to figure out which coil is failing or you can save yourself the trouble and replace all 4 and the spark plugs. before you do that though check your wireing going to your coils look for broken wires or the ground that is next to the #1 coil that is the one closest to the front of the motor and you. hope that helps. that will be the start to fixing your issue also when you pull out the spark plug look down the hole first and make sure that there is not oil in the bottom of the hole if that is the case you will need a valve cover gasket as well. good luck hope that helps

Sep 16, 2009 | 1999 Volkswagen Passat

1 Answer

Where is the camshaft position sensor located in a 2001 VW Passat


when you are looking at the engine pull off the plastic cover on top then the front cover that covers you timing belt there is a wire harness tha goes right to it in the left upper coner two ten mil bolts and it comes off careful not to drop bolts down in belt that could be bad. it is that easy

Aug 31, 2009 | 2001 Volkswagen Passat

1 Answer

04 vw passat reversing sensors have stopped working , looks like someone has caught the bumper in a carpark or something . Can they be reset.


just trace for the disconnected wires and fix it by reconnecting it and soldering it back and insulating the wires. There's no need to reset I guess

Aug 17, 2009 | 2004 Volkswagen Passat

3 Answers

Oil in water resovour vw 2002 passat


Could be just the OIL COOLER. VW IS CORRECT.
If the oil cooloer fails internely you will have a mix of coolant and oil. In the engine and in the Radiator,

But not to say the other guys were wrong...

May 27, 2009 | 2003 Volkswagen Passat

Not finding what you are looking for?
2007 Volkswagen GTI Logo

Related Topics:

491 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75117 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...