Question about 2002 Jeep Grand Cherokee

1 Answer

Power window glass keep coming out of the clips, do I need to glue the glass to the clips with some sort of putty??

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

Use silicone marine silicone adhesive for that. regular stuff also works but may come loose after a while.

Posted on Jul 18, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Bought window regulator for 2000 Olds Alero but plastic clip that is attached to bracket and glues to window is broken . So can't connect regulator to clip . Can clip be replaced ? How can old clip that's...

Replacement clips are available through specialty auto parts stores...there are many tricks or solvents that will loosen the glue on the broken clip...if you damage the glass, you can find a popular window replacement, inspect the clip too, at your nearby salvage yard or online...Hope this helps.

Nov 06, 2013 | 2000 Oldsmobile Alero

1 Answer

1996 Mercury Mystique Window

Here are the instructions:
    • Gently remove the door panel of your Contour, ensuring that you don't break the three door clips that hold it on. As you pull the panel from the door, support the panel from below. This will ensure that none of the wiring inside the door is damaged. Release the wiring from the components inside the door, including the power window mechanism, power lock mechanism (if equipped) and the stereo speaker. Place the door panel in a safe area with the clips so they are accessible when you are ready to replace them.
    • 2Remove the window glass by sliding it up and out of the door. Support the glass from the bottom so it doesn't drop and break. Window glass for a Contour can cost around $150 to replace. After you remove the glass, put it in a safe place. You may want to wrap it in old towels or blankets to protect it until you are ready to reinstall it.
    • 3
    • Unplug the wires from your Contour's window motor, and remove the screws from the window motor and regulator. Remove the power window motor and regulator from your Contour to make way for the new parts.
    • 4Install the new window regulator into the door, and replace the screws that held them in place.
    • 5Replace the window glass into the door, and connect it to your Contour's power window motor and regulator assembly.
    • 6Replace the door panel. Reconnect the wiring for the power window and power lock controls, and replace each clip that connects the panel to the door.

Jul 26, 2012 | 1996 Mercury Mystique

1 Answer

The brackets that attach to the driver's window on my son's 2003 Grand Am have broken due to forcing a frozen window. The window is no longer attached to the slide mechanisms. I am wondering...

Hello, normally just the window sashes break. this is the plastic part that is glued on the bottom of the glass. you can but these asahes at your dealer. they simply just glue on with a special glue

Sash Channel Came Off Glass; Adhesive on Glass
  1. Remove the door glass and lay it on a protected table.
  2. Mark the location of the clip with tape.
  3. Remove the adhesive with a one edge razor blade.
  4. Clean the glass with Isopropyl alcohol.
  5. Important: Install adhesive into the applicator and squeeze some adhesive out before you install the mixing tube. After the mixing tube is installed, run a test bead the length of the mixing tube to ensure a good mix.
  6. Fill the sash channel clip with adhesive.
  7. Install the clip in the marked location.
  8. Reinstall the door glass and put the glass in the full up position for 24 hours.

Cut off the bottom edge of the guide with a cut off wheel. (Refer to the illustration above.)

Using a thin flat blade putty knife and a hammer, carefully remove the plastic piece on each side of the glass. (Refer to the illustration above).

  • Clean any adhesive from the glass using a one-edge razor blade. (Refer to the illustration above).
  • Clean the glass with Isopropyl alcohol.
  • Important: Install adhesive into the applicator and squeeze some adhesive out before you install the mixing tube. After the mixing tube is installed, run a test bead the length of the mixing tube to ensure a good mix.
  • Fill the sash channel clip with adhesive.
  • Install the clip in the marked location.
  • Reinstall the door glass and put the glass in the full up position for 24 hours.

  • 22689012
    Sash, Side Door Window
    12378568 (US)
    88901676 (Canada)
    Structural Urethane Installation Adhesive

    Jun 06, 2011 | 2003 Pontiac Grand Am

    1 Answer

    How do you get the back off of a rearview mirror to stick it back n the window

    Some have a cover hiding the screw or from the bottom theres a clip that need to be pryed back and held while you slide mirror of bracket, if theres no screw on the mirror to loosen then theres a clip arm holding it, also make sure to glue the right way take note of how it goes on because once you glue to glass its not coming off.

    Dec 07, 2010 | 2004 Kia Optima

    1 Answer

    I need a diagram of a window setup

    They are stuck on with glue ! you can fix em with more glue but it dont last .

    Mar 24, 2009 | 1994 Isuzu Trooper

    1 Answer

    Window replacement passenger side

    There is 2 sash clips that need glued to the new window. Note the placement of the clips on the broken window. Get a goods glue from a local glass replacement company

    Feb 15, 2009 | 1999 Oldsmobile Alero

    2 Answers

    1998 blazer rear window latch comes unglued from window

    You need mirror glue. If this is help, please post as such. If it is a fixya, please post as such.TY

    Jan 21, 2009 | 2001 Chevrolet Blazer

    3 Answers

    Convertible top

    I have the same problem. I got acetone and removed the old glue from the glass. Then  I reglued it with gorilla glue. This stuff explands into this yellow hard foam, so you have to be careful not to put on too much and not to get it on the outside of the top. I stuffed the back window area inside the car with pillows to push the glass up, then carefully applied the glue to the edge of the glass with a paintbrush. Then I covered the glued area on the outside with plastic bags of kitty litter to hold the fabric against the glass. Takes 4-5 hours to dry. Worked beautifully so far. Got a little thick and a couple places and I removed the excess with a razor blade. Then on the inside, I applied a small amount of the same glue with a paintbrush to the inside of the little track round the window. Then inserted the edge of the headliner into the track. Did all of this work with the top slightly opened to take the pressure off. So far so good. One week and counting. Hopefully it will hold up to the heat and sun. 

    Sep 01, 2008 | 2003 Volkswagen New Beetle Convertible

    Not finding what you are looking for?
    2002 Jeep Grand Cherokee Logo

    Related Topics:

    143 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Jeep Experts


    Level 3 Expert

    79865 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22326 Answers

    Kevin Daniels

    Level 3 Expert

    1455 Answers

    Are you a Jeep Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides