Question about Ford E-Series

1 Answer

I have a 1998 au ford station wagon need a diagram on how to put the multi-ribbed super belt back on 6pk2380 thanks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 77 Answers

A diagram should be on the fan shroud or on a sticker under the hood. Or you can buy a Chilton's or Hanes Manual

Posted on Jul 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Belt diagram for 2001 Saturn LW200 (station wagon)?


Go autozone.com type in you make and model it will give you the diagram

Sep 03, 2012 | 2001 Saturn Lw 4dr Wagon

1 Answer

1998 saturn serpentinebelt diagram


I had 4 saturns, 91-01, all of them had a little silver sticker in the engine bay with a belt diagram, also showing how to release tension to remove and replace the belt. further if you note the inside of the belt is ribbed, thus the belt goes around those pulleys which are ribbed, and the smooth back of the belt goes against those pulleys which are not ribbed.

Jun 26, 2011 | 2000 Saturn SL

2 Answers

Need diagram for serpentine belt 1998 ford escort zs2


http://www.clubfte.com/users/racerguy/zetecbelt.gif

Hope that helps you.

Dec 05, 2010 | Ford Escort Cars & Trucks

1 Answer

Serpentine belt installation on an 1998 ford ZX2 escort


If there is no diagram on the underside of your hood, or around the engine compartment, just wrap it around the crankshaft, and work your way around the pulleys, going flats to flats, ribs to ribs. There may be a couple of combinations, but you'll get it.

Nov 13, 2009 | 1998 Ford Escort

1 Answer

Belt routing diagram 98 zx2 2.0


1) Start with the alternator.
2) Forward to the smooth idler
3) Forward to power steering
4) Down to A/C compressor
5) Back to crank pulley
6) Forward around tensioner
7) Back glancing off of water pump
8) Back glancing off of ribbed idler
9) Up around alternator (where you started)
Good luck!

Sep 11, 2009 | 1998 Ford Escort

1 Answer

1998 Jeep Grand Cherokee - Multi-rib belt Removal & Replacement


Check on upper rad shroud or under hood for routing diagram. Depending on what engine, procedure may vary a little. I wouldn't panic on replacing anything other than belt unless you noticed something noisy under hood in last while.
If not up to it, a mechanic should be able to do it for you in a few minutes usually, but won't hurt to ask before, just in case.

Jun 27, 2009 | 1998 Jeep Grand Cherokee

2 Answers

The diagram on a 1998 ford contour does not match the way to put on the serpentine belt. It's a diagram under the hood of my car but does not match that diagram Can u show me a picture


Follow the diagram again. Sometimes the belt goes on the inside or the outside of the belt. If you see a pulley that has a smooth surface only then the outside smooth part of the belt goes over it. When you see a pulley that has the ribs in it the belt matches the ribs. If you follow the pulleys you will get the belt on correctly. They can be confusing until you have replaced a few. But, just follow the pulley surfaces and you will get it. Remember match ribs to ribs and smooth to smooth. Good luck.

Mar 06, 2009 | 1998 Ford Contour

1 Answer

Isuzu Trooper V6 2001 multi rib belt replacement


They have an automatic tensioner, like a spring loaded pulley. They are usually quite easy to pull back using a power bar or spanner. For the routing diagram, click here

Mar 01, 2009 | 2001 Isuzu Trooper

3 Answers

Need diagram for routing of the serpentine belt on 98 ZX2 Yes having problem threading the belt correctly needa an detailed diagram kind regards


Go on the Dayco belts web site. They make serpentine belts and a pretty good data base of belt diagrams for any vehicle they make a belt for.

Feb 02, 2009 | 1998 Ford Escort

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...