Question about 1994 Jeep Grand Cherokee

2 Answers

PC Board Bulbs in the Headlight control----14V 14W They connect to the board it self.....

Posted by on

  • 4 more comments 
  • woodfurd Jul 18, 2009

    I would need to Email a pictue of what I'm looking for...

    This are used Inside of a 1994 Grand Cherokee Headlamp control box on the PC Board.....

    Mine has Auto Lghts on W/Fog Lights.....

  • woodfurd Jul 18, 2009

    Nope...

  • woodfurd Jul 20, 2009

    Done

  • woodfurd Jul 20, 2009

    Done

  • woodfurd Jul 20, 2009

    Done

  • woodfurd Jul 20, 2009

    The bulbs are replaced and I found a break in a Trace on the board it self...



    Now I'm wounding why my Radio display does not light up---IE: You can't see what station you're on...All input voltages are good and there is a "Black Spot" on the lower right corner of the display tube----Is the tube itself cooked??

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 15,935 Answers

These bulbs are available at Radio Shack or other parts supplier like Mouser.com etc.
Just be sure to get the same 14v 14w values.

Thanks

:D

Posted on Jul 20, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 2,200 Answers

Hi

Coluld you clarify your question please as it is unclear what you want to know exactly. Post up a comment with more detail and I will be happy to look at this for you.

Thanks

Posted on Jul 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The drl indicator on dash board is on and both the drl and high beans are not working. is this blown bulbs or blown fuses


Most likely switch, but check fuses first. If they blow again, you have bad short in most likely wires to headlight. Could also be Diming switch relay. Or connections from and to it.

Mar 08, 2015 | 2010 Honda Accord LX

2 Answers

How to find an electrical disturbance in 1998 ford expedition


Normally this condition is the result of a poor body ground connection. Testing for this can be deceiving. At the static(nothing on) condition, testing can show a good ground. However when a circuit is excited, it has a determined resistance and a set current flow. If the ground connection to this or a branch circuit is loose, corroded, or broken wire. This will allow just enough connection to show as being good, but not good enough to complete the circuit with the required amount of connection when energized.

Nov 30, 2014 | 1998 Ford Expedition

1 Answer

Nissan pathfinder 2005 climate control lights


There is no common issue. But if all blinked off at the same time there is a printed circuit board problem inside the control, the tiny bulbs are hard wired to the circuit board. I would do a google search for a used control head, a new one will be very pricey.

Mar 22, 2012 | 2005 Nissan Pathfinder LE

1 Answer

Toyota Sienna 2004 Headlight Problem


If you have the HID bulbs, and there is moisture in the bottom of the assembly, the high voltage box at the bottom will not work. this requires removing the whole headlamp, removing the circuit board from the bottom and drying out. I have done mine twice before finally finding how water was getting in at the top seam of the lamp assembly. You will have to dis-assemble part of the wheel well and bumper cover to gain access to all the mounting bolts. Best of luck

May 02, 2010 | 2004 Toyota Sienna

1 Answer

My 2000 jetta burns out its lights often and then the high beam dummy light turns on. I've replaced the sockets twice but bulbs last only about a day before the passenger side burns out again. The...


Are the bulbs ate right wattage? If they are too high they will generate enough heat to melt connectors, switches and so on. Are you touching the glass before fitting them. Headlight bulbs have to be free of contamination. It might be tbat your voltage regulator is charging at too high a voltage. This could damage much of your electronic equipment and it would also overheat the battery which could cause it to explode. Put a volt meter across the battery and rev the engine. Anything much over 14v is high but if it burns out bulbs that quickly it would be much higher. You would need to replace a defective voltage regulator.

Mar 15, 2010 | 2000 Volkswagen Jetta TDI

1 Answer

2 indicator lamps in the climate control panel are out


if your down to the board, you've done the hard part. theres some torx screws, and pull he knobs off. remove the board and they are little solid state bulbs soldered into the board. i buy 12v pin style mag lite bulbs to put back in

Aug 24, 2009 | 2003 Pontiac Sunfire

2 Answers

Change lens cover1998 grand caravan


There's really no way to change a lens cover on a headlamp or tail light on that vehicle. You'll have to change the whole light/housing. For the tail light, open the hatch and remove the two screws. Depending on weather you buy new or used, you may have to replace the board on the back. For the headlight, open the hood. There are two 10mm bolts on the top and two that come straight in from the back. On the driver's side it might be easier to take out the battery. Be careful though, these bolts have a tendency to break easily. Unplug the bulbs. If you remove the bulbs, be careful not to touch the glass on the headlights as these are usually halogen bulbs. The oil on your fingers will create a "hot spot" causing the bulbs to fail soon.

Jun 29, 2009 | 1998 Dodge Caravan

3 Answers

Center dash lights out.


Like stated above there are 3 small bulbs soldered onto the cuircut board. To replace yourself you must remove the radio bezel above and the shift bezel, these just snap into place though be carefull and always try to pull evenly to avoid breaking any tabs. The whole heater panel then can be pulled off. Unclip all the wiring harnesses, then unscrew the heater control itself from the panel. Remove the back of the heater unit to access the cuircut board. Remove the burnt bulbs by the base, slowly wiggling the base until they snap off. Go to radio shack and buy bulb #272-1141 (mini lamp 12Volts, 25mA). Remove the wires from the new bulb and melt off the glue on the base of the bulb with a lighter. Now you will have two metal leads exposed at the base of the bulb. Insert the leads into the base you removed from the cuircut board and slightly bend outwards so the base stays on. Dab a little bit of solder onto each of the prongs, then solder each prong onto the appropriate cuirtcut. be careful with the soldering iron not to touch any other areas of the cuircut board. I would suggest buying the long thin attachment for this procedure, as the prongs are small and the base of the bulb will be close to the cuircut board when soldering. This procedure is not for the novice, and if you are I would practice practice practice before you attempt to install the bulbs. I have done basic soldering before but nothing on cuircut boards, and I changed 3 burnt bulbs no problem, though I have to buy extra bulbs because on my first attempt I cut all of the metal leads off. Cost me about 5$ to do, since I already have a soldering iron. Good luck.

Jan 12, 2009 | 2005 Jeep Grand Cherokee

Not finding what you are looking for?
1994 Jeep Grand Cherokee Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...