Question about 2003 Dodge Stratus

1 Answer

Where is the windshield washer relay in a 2003 stratus

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 322 Answers

It suposed to be on the engine bay driver side, if not on the top of the fuse box.

Posted on Jul 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wipers will not turn on 2006 colorado


There are two relay's in the under hood fuse / relay box . Wiper relay an wiper relay 2 . Maybe one is bad . also check fuse #14 25 amp. Wiper fuse.Plus the BCM - body control module has a hand in making the wipers work . Are you familiar with automotive electronic control modules ?
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper micro relay
• Wiper 2 relay
• Wiper diode
• Windshield wiper motor
• Windshield washer pump
• Windshield washer nozzles
• Windshield washer solvent container
• Windshield wiper arm and blade assemblies
• Windshield wiper transmission
• WIP/WASH 10A fuse
• WIPER 25A fuse

Wiper/Washer System Description
The body control module (BCM) controls wiper motor low speed operation. The washer pump and high speed operation are controlled directly by the wiper/washer switch. The windshield wiper/washer switch supplies voltage on the signal circuits to the BCM for windshield wiper/washer operation. When WASH, MIST, DELAY, LOW, or HIGH is detected, the BCM energizes the wiper micro relay by suppling voltage to the relay coil. This allows battery voltage from the WIPER fuse to flow through the relay switched input then through the contacts and out the relay switched output to the wiper 2 relay switch contacts. Since the wiper 2 relay switch contacts are normally closed to the low speed circuit of the windshield wiper motor, the motor will operate at low speed.

Do you have any speed !

Oct 06, 2017 | Cars & Trucks

1 Answer

How do I find out if the wipers on my 2006 H3 Hummeris on a relay?


The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper micro relay
• Wiper 2 relay
• Wiper diode
• Windshield wiper motor
• Windshield washer pump
• Windshield washer nozzles
• Windshield washer solvent container
• Windshield wiper arm and blade assemblies
• Windshield wiper transmission
• WIP/WASH 10A fuse
• WIPER 25A fuse

Wiper/Washer System Description
The body control module (BCM) controls wiper motor low speed operation. The washer pump and high speed operation are controlled directly by the wiper/washer switch. The windshield wiper/washer switch supplies voltage on the signal circuits to the BCM for windshield wiper/washer operation. When WASH, MIST, DELAY, LOW, or HIGH is detected, the BCM energizes the wiper micro relay by suppling voltage to the relay coil. This allows battery voltage from the WIPER fuse to flow through the relay switched input then through the contacts and out the relay switched output to the wiper 2 relay switch contacts. Since the wiper 2 relay switch contacts are normally closed to the low speed circuit of the windshield wiper motor, the motor will operate at low speed.

Low Speed Operation
When the wiper switch is in the Low position, voltage is supplied through an internal resistor to the signal circuit. The body control module (BCM) monitors the windshield wiper switch signal 1 circuit, and energizes the wiper micro relay which will operate the windshield wiper motor. The wiper motor will operate at low speed, since the wiper 2 relay is de-energized. Low speed can also be commanded with a scan tool, by commanding Wiper Relay Cmd. ON and OFF. Refer to Scan Tool Output Controls .
High Speed Operation
In the High position, the windshield wiper/washer switch supplies voltage to both the wiper micro relay and wiper 2 relay coils. This energizes both relays and allows battery voltage from the wiper micro relay switched output to the switched input of the wiper 2 relay through its contacts and out the switched output of the wiper 2 relay to the high speed circuit of the windshield wiper motor. The windshield wiper motor will operate at high speed. During high speed wiper motor operation the wiper switch signal circuit is at the low speed signal voltage, and the body control module (BCM) supplies redundant voltage to the wiper relay via the wiper diode.

This info is out of hummer factory service manual !

Dec 10, 2016 | 2006 Hummer H3

1 Answer

Looking for the fuse for the wiper motor 2008 chevy impala


WPR fuse 25amp under hood fuse box .
Wiper/Washer System Components
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper PCB relay
• Wiper high PCB relay
• Windshield wiper motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR fuse 25 A
• WSW fuse 10 A
This is more then likely not a fuse issue !!!!!!!
Low Speed Operation
When the wiper switch is in the low speed position, ground is applied through the switch internal resistor and the wiper switch low signal circuit to the body control module (BCM). In response to this signal, the BCM energizes the WIPER PCB relay by applying battery voltage through the wiper relay control circuit to the coil side of the relay. This allows battery positive voltage from the WPR fuse to flow through the switch input side of the WIPER PCB relay and out to the switch input side of the WIPER HIGH PCB relay. Since the wiper high relay is de-energized and its switch contacts are normally closed to the low speed control circuit of the windshield wiper motor, the motor will operate at low speed.
Wiper motor low speed operation and the wiper PCB relay can also be commanded ON/OFF by using a scan tool. Refer to Control Module References.
The PCB relays mentioned above are soldered right into the circuit board inside the fuse/relay block under the hood . There are alot of reasons for the wipers not to work ! The fuse could be blown but fuse's don't just blow for no good reason , short to ground , low resistance high current flow etc.... Intermittant !

Power and Grounds
With the ignition in the ON position, accessory voltage is supplied through the 25A WPR fuse to the WIPER PCB relay, the WIPER HIGH PCB relay and the WS WASH PCB relay that are all located in the underhood fuse block. Refer to Wiper/Washer Schematics.
G200 provides ground for the windshield wiper motor and the WIPER PCB relay. G100 provides ground for the windshield washer fluid pump and the windshield washer fluid level switch.

Dec 04, 2016 | Cars & Trucks

1 Answer

Wheres the relay for the wipers on a 2006 dodge stratus


its in the engine compartment fuse panel.check for power and ground at the wiper motor

Oct 19, 2014 | 2006 Dodge Stratus

1 Answer

Fuse and relay diagram for 2005 dodge stratus


look on the inside of the cover you removed to access the relay center, it has all the relays labeled for there position

Jul 10, 2012 | 2003 Dodge Stratus

2 Answers

When I pull back wiper lever to spray windshield, wipers move but do not spray windshield. When I turn wiper lever end forward to spray rear window, it sprays front windshield. How is this possible?


Possible there is fault in the cluster switch , possible that the switch is not contacting according to the intended function to power the front washer and rear washer motors.
You need to check the output or using a multimeter the switch continuity of the wiper cluster switch.

Apr 04, 2011 | 2003 Pontiac Vibe

2 Answers

Need to know the fuse box diagram, what fuse pertains to the wipers... the wipers quit today and I do not have the manual. I opened the hood and see the fuses etc, but have no idea which one is for the...


fuse panel in car on driver side by left knee under dash


Visual Inspection Chart
Mechanical Electrical
  • Wiper linkage
  • Washer nozzles
  • Washer pump hoses
  • Central junction box (CJB) Fuse 211 (15A), Fuse 215 (30A)
  • Multifunction switch
  • Rear window wiper switch
  • Wiper run/park relay
  • Wiper high/low relay
  • Windshield wiper motor
  • Windshield washer pump
  • Rear window washer pump
  • Circuitry
  • Battery junction box (BJB)
  • CJB
  • Generic electronic module (GEM)

Dec 11, 2009 | 2003 Mercury Sable

3 Answers

I have a 2003 Chevy Trailblazer Windshield Wiper problem.


As it turns out, there is a recall On 2002-2003 Chevy Trail Blazer's
Windshield Wiper/washer
NHTSA No. 04V046000
Recall Date: Feb, 4th, 2004
Call your dealer to see if this is still under the recall to be fixed.
RECALL: 2002 - 2003 Chevrolet Trailblazer NHTSA Campaign Number: 04V046000 www.nhtsa.dot.gov
Manufacturer GENERAL MOTORS CORP. Recall Date: FEB 02, 2004 Potential Number Of Units Affected: 581394 Description VISIBILITY:WINDSHIELD WIPER/WASHER Summary CERTAIN SPORT UTILITY VEHICLES HAVE WINDSHIELD WIPER SYSTEMS THAT WILL NOT TURN ON, CEASE OPERATION WHILE IN USE, FAIL TO TURN OFF/ON BY THEMSELVES (MOISTURE SENSITIVE WIPER SYSTEM), OR HAVE CONTINUOUS WINDSHIELD WASHER PUMP OPERATION BECAUSE THE PRESENCE OF WATER WITHIN THE WIPER MODULES CAN EITHER CAUSE A SHORT CIRCUIT OR CAN LEAD TO THE CORROSION OF COMPONENTS WITHIN THE MODULE. Consequence DEPENDING ON THE OCCURRENCE AND WEATHER SITUATION, DRIVER VISIBILITY COULD BE REDUCED, WHICH COULD RESULT IN A CRASH. Remedy DEALERS WILL COVER THE WINDSHIELD WIPER MODULE VENT HOLE WITH A PATCH. ALSO, THE WIPER MOTOR, CIRCUIT BOARD, AND ELECTRICAL CONNECTOR WILL BE INSPECTED TO SIGNS OF WATER INTRUSION AND/OR CORROSION AND BE REPLACED AS REQUIRED. THE RECALL BEGAN JULY 6, 2004. OWNERS SHOULD CONTACT CHEVROLET AT 1-800-630-2438; OLDSMOBILE AT 1-800-630-6537; OR GMC AT 1-866-996-9463.

Nov 25, 2008 | 2003 Chevrolet TrailBlazer

1 Answer

Windshield wipers and washer


First thing to check is the fuse and relay.

Jul 09, 2008 | Hyundai Motor 2003 Elantra

Not finding what you are looking for?
2003 Dodge Stratus Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...