Question about 2004 Ford Ranger

1 Answer

Wiper motor i replaced the wiper motor 3 times is there something i am overlooking

Posted by on

  • yadayada
    yadayada May 11, 2010

    THE SWITCH?

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 55 Answers

Poss bad wiper switch or fuse.

Posted on Jul 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i access the rear wiper motor of a 2011 equinox?


Remove the interior panel from the rear hatch door. check for voltage at the wiper motor, avoid overlooking a blown fuse or bad switch.

May 29, 2017 | Cars & Trucks

1 Answer

2003 Pontiac Bonneville. Why do wipers stick on or fail completely?


I would suggest checking the linkage to the wiper arms I had the exact same problem also on 03 Bonnie my solution was a small aquarium air line over the vent then secured in the wiper arm then completely sealing every seam on the motor flex-seal works just fine if you don't have silicone sealer let it cure and at least for me problem solved. I had previously lost 2 motors in less than 24 hrs . Good Luck hope this helps

May 08, 2015 | 2003 Pontiac Bonneville

2 Answers

97 jeep cj windows and wipers stopped working fuses are ok


97 wrangler right? CJ ended in 86 (last year)
97 TJ, you mean, or was posting to Cherokee correct all along./?????
factoid:
The Chrysler Corporation bought out AMC in 1987, shortly after the Jeep CJ was replaced with the AMC-designed Jeep Wrangler or YJ.


test the fuse, looking only finds the ones blow to H3LL
they can in fact just crack a bit. and are in fact bad.
use any DMM or any ohmmeter, "resistance Rx1 or RX2 range , low range) 0 ohms good, , infinity bad.
only that works. every time.
lets read the FSM together.
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service
wipers first. USA not export.
Front wiper not rear. ok>?
page 8w-53 wiper schematic.

fuse 2 and 3 must be good.
then fuse 14 front wiper ,fuse 12 is rear
if the fuses are good, (truely) we never ohm fuses we use VOLTS
on both sides of fuse, volts never lies.
then what is bad, easy bad wiper switch, motor or ground to motor.
the voltmeter again wins the toss and if no 12vdc to motor
then the switch or wire are bad.
if you have 12v to motor then motor is bad , if ground to motor is no cut.

now windows. what windows, are then not crank windows or zipper windows?

i think you posted wrong car,,

Mar 20, 2014 | 1997 Jeep Cherokee Country

1 Answer

Wipers will not work. fuse is ok wiper motor is new wiper switch (on/off switch) is ok 1991 Plymouth sundance


Sounds like you have overlooked something.
Does the motor have power and ground when the switch is on low or high ?

Aug 08, 2013 | Plymouth Sundance Cars & Trucks

2 Answers

No windshield washer fluid pumping


1) Fluid resevoir is empty
2) Fluid is frozen
3) Washer fluid hose is disconnected, blocked or kinked
4) Washer switch is faulty
5) Washer pump motor is defective
6) Washer pump fuse is blown

Dec 24, 2010 | 2003 Oldsmobile Alero

1 Answer

Ever since i replaced the wiper motor on 2003 chevy impala the wipers stop in up position instead of down position when stop- ped on delay position.is it something i did wrong when replac- ing the...


try this fix
remove wiper arms from where they connect on car
turn wiper moter on then off. turn ignition off
if wiper motor is good it should put spline in off position and now all you need to do is replace wiper arms in the correct position they would be in when wipers are turned off

Dec 14, 2010 | 2003 Chevrolet Impala

1 Answer

VW Golf 2001 Rear Window Wiper stays on.


Back window wiper switches/levers are tricky, especially on German-brand automobiles.
Just make sure that the lever/switch is on 'O' or OFF. I overlooked this once on an Opel Astra, and mistook it for the signal lever. Move the switch to all positions to ensure that there is no damage to the physical contacts or electronic controllers of the wiper.
If the wiper cycles even in off position, the controller or motor will need to be replaced.

May 21, 2010 | 2001 Volkswagen Golf

1 Answer

06 Frd Rngr linkage and witper motor.


Yes.. you have to time the leakage on wippers

Feb 26, 2010 | 2007 Ford Focus (3 Door) Hatchback

Not finding what you are looking for?
2004 Ford Ranger Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...