Question about 1995 Toyota Camry

1 Answer

Exchange ignition switch in toyota camry - 1995 Toyota Camry

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 1,861 Answers

Remove the lower portion of the dash, and the steering column shroud. Using a DREMEL tool, and a ut-off disc, cut s line in the bolts that holds the ignition switch in, deep enough to insert a flat-blade screwdrive; then simply remove the 2 bolts.

Posted on Jul 18, 2009

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 98 Answers

SOURCE: How to remove ignition cylinder from Toyota Camry 1993

Here are step-by-step instructions for the removal and re-installation of your ignition cylinder on your Toyota. Hope this sheds some light on the subject and solves your problem. Have a great day!




  1. Disconnect the negative battery cable. If equipped with an air bag, wait at least 90 seconds before working on the vehicle.
CAUTIONSome models covered by this guidemay be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in .
  1. Remove the lower steering column cover. Unfasten the ignition switch connector under the instrument panel.
  2. Remove the screws which secure the upper and lower halves of the steering column cover.
  3. Turn the lock cylinder to the ACC position with the ignition key.
  4. Push the lock cylinder stop in with a small, round object (cotter pin, punch, etc.).
On some vehicles, it may be necessary to remove the steering wheel and combination switch first.
  1. Withdraw the lock cylinder from the lock housing while depressing the stop tab.
  2. To remove the ignition switch, unfasten its securing screws and withdraw the switch from the lock housing.
To install:
  1. Align the locking cam with the hole in the ignition switch and insert the switch into the lock housing.
  2. Secure the switch with its screw(s).
  3. Make sure both the lock cylinder and column lock are in the ACC position. Slide the cylinder into the lock housing until the stop tab engages the hole in the lock.
  4. Install the steering column covers.
  5. Connect the ignition switch wiring.
  6. Connect the negative battery cable.

Posted on Nov 23, 2008

  • 65 Answers

SOURCE: 1998 toyota

There is a pin that you have to push in on the bottom of the lock cylinder housing.It is recessed in a hole.You have to turn the key to acc or on to get it to push in.Once you push it in you can pull the key and lock cylinder out.

Posted on Dec 02, 2008

  • 1 Answer

SOURCE: Key will not turn ignition switch.

try sanding down the key alittle - saved me a fortune on my 96 civic

Posted on Apr 30, 2009

ZJLimited
  • 17970 Answers

SOURCE: how do you access the ignition switch on a 1999

Remove the plastic covers around the steering column and try to get the key into the ACC position then you can deprss the release pin and pull the cylinder out, get the new cylinder first so you can see where the release pin is.

Posted on Oct 19, 2009

  • 184 Answers

SOURCE: 1992 Toyota Camry won't crank

Check the ground cable going from the battery to
alternator, then to chassis. Make sure there is no
rust at the chassis ground wire terminal, and that it
is very tight. The fusible link will be off the alternator
red power cable,usually, but not 100% on that car.
Good luck.

Posted on Mar 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

92 toyota camry, where is the ignition kill switch located


No "kill" switch.

What is the problem you are having?

Apr 03, 2013 | 1992 Toyota Camry V6

1 Answer

How can I tell if the ignition switch is bad in my toyota camry?


You need a tachometer compatible with the Toyota Camry's ignition system. Start up the Camry's engine and let it reach normal operating temperature. Connect the tachometer tester probe to terminal IG of the Data Link Connector 1. Connect terminals TE1 and E1 of the DLC1 with a jumper connector. Inspect the tachometer's timing. It should be between 8 and 12 degrees Before Top Dead Center. Set the timing as necessary. Tighten the hold-down bolt and make sure the ignition timing advances. Ignition Coils Disconnect the negative terminal from the Camry's battery. Remove the two nuts and clips on top of the cylinder head cover, then remove the cover. Disconnect the four ignition coil connectors and the bolts retaining the coils. You can now remove the coils. Replace the coils as needed. Connect the bolts and coil connections and replace the cylinder head cover.

Aug 31, 2010 | 1999 Toyota Camry

2 Answers

How do i start my toyota camry after i have hit the kill switch?


I guess you tried reversing the kill switch. But did you try it after you put the ignition on? Some switches work this way. Try different things. ignition on, ignition off, etc

Apr 28, 2010 | 2000 Toyota Camry

1 Answer

My 1993 toyota camry's automatic door won't lock. when i press the lock button or use the key, it just click back to open. what could theproblem be?


it could be a bad door switch or the key switch in the ignition, it thinks the key is in the ignition so it doesnt let you look the door it unlocks it, may need to replace the ignition or dissable the sensor in the igniton by cliping the wiring .

Mar 01, 2010 | 1993 Toyota Camry V6

1 Answer

Ignition switch


there are screws under the cover of the ignition switch. remove them and you can see the switch.

May 02, 2009 | 1987 Toyota Camry

1 Answer

Key will not turn ignition switch.


try sanding down the key alittle - saved me a fortune on my 96 civic

Apr 30, 2009 | 1991 Toyota Camry

3 Answers

1998 toyota


There is a pin that you have to push in on the bottom of the lock cylinder housing.It is recessed in a hole.You have to turn the key to acc or on to get it to push in.Once you push it in you can pull the key and lock cylinder out.

Dec 01, 2008 | 1998 Toyota Camry

Not finding what you are looking for?
1995 Toyota Camry Logo

Related Topics:

299 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...