Question about 2000 Chevrolet Blazer

1 Answer

How do you get the fuel rails back in side the spider holding

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 87 Answers

They push in - check to make sure that the two connectors on the spider holding are not broken.

Posted on Aug 02, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

4.3 V6 in 1993 S10 blazer I'm getting fuel to fuel rail but not to injectors. I've replaced the fuel spider but still won't start unless u squirt gas into throttle body


As the injectors are connected to the fuel rail but you are not getting fuel out of the injectors then the problem be with the electronic control of the injectors (immobiliser-cam/crank position sensors-ECM-wiring). Unless you got bad fuel or used a cleaner that has blocked up the tips of the injectors.

Aug 14, 2014 | Cars & Trucks

1 Answer

Car is hard starting


Find the fuel pressure regulator on the fuel rail. 3.4 ant 3.1 liters it will be on the front rail on the drivers side near the throttle linkage. On a 3.8 it will be on the back rail about in the midle. Remove the vacuum hose from it and start the vehicle. If gas comes out it is bad. if no gas comes out than you will need a fuel pressure gauge to see if fuel pressure is holding. If it is not than the fuel pump is the next most likely suspect.

Jul 02, 2014 | 2004 Pontiac Grand Prix

1 Answer

Leak at fuel rail on volvo 960


take a lead from your battery .then reach under the inlet manifold. remove the 10mm bolt and copper washers one each side of that bolt. that is the feed line from your fuel rail to the cold start injector .now remove each of the ten mil bolts holding on your fuel rail . now remove the clips holding the injectors to your fuel rail. place some clothes under the fuel rail and lift off . care needed due to fuel wear eye protection due to fuel pressure..

Dec 01, 2013 | 1995 Volvo 960

1 Answer

Where is the fuel filter on 1991 spider?


Call the dealership parts department to find out,

Nov 29, 2012 | 1991 Alfa Romeo Spider

1 Answer

Fuel rail in a 1997 3.8L pontiac firebird


to remove fuel rail you need to remove 2 mounting bolts holding fuel rail in place.

Aug 27, 2012 | Pontiac Firebird Cars & Trucks

1 Answer

How to remove fuel injector #3 diagram


Hi, the picture shown is the driver's side of the engine. Go to the passenger's side and remove the 2 similar screws holding the fuel rail. Disconnect all of the injector connectors on that side. Raise the rail up carefully until the injectors come free from the manifold. #3 is third back from the front of the engine. Twist and pull it out of the fitting on the rail. Oil the oring on the new injector and twist it in. Oil all of the lower orings and slip the injectors back into the manifold. Replace the 2 fuel rail bolts and reconnect the injectors. Please let me know if you have questions, and thanks for using FixYa.
jturcotte_1921.gif

Jul 09, 2011 | 1999 Ford Expedition

1 Answer

Gas line leaking by engine how do repair that?


Where is it leaking? If its at the fuel rail fuel pressure regulator you may need a new regulator if leaking on the metal part. If its leaking at the rail side its just the "O" ring. Relieve fuel pressure(push in valve under plastic cap right side beside alternator on rail. Remove the torx screw holding regulator bracket. Pry out and replace "O" ring, reassemble. If its not the regulator it may be a fuel injector, you need to remove the fuel rail and replace both the upper and lower injector "O" rings. This however needs the intake manifold removed to repair.

Jan 29, 2011 | 2002 Buick LeSabre

3 Answers

I have a 2000 chevy blazer vortec 4.3 thats has the "spider" fuel rail. i have presure all the way to the intake lines. i have spark but it will not start i changee the fuel pump a couple months a...


check the 2 wire molley plug going around the front of the intake down into the injector i have found many of those tend to overheat on the plug just cut it and splice the wires back togehter

Jan 17, 2010 | 2000 Chevrolet Blazer

3 Answers

94 jimmy turns but wont start, I replaced the fuel pump and


see if your getting fuel to the top, find the fuel rail on the top of the motor you will see a bleeder valve push in the the little serator valve and see if fuel comes out. if not the pressure regulator could be bad. if none there take the filter loose on the pump side and see if fuel comes out there. i believe this has the spider type injector setup on it and this could be bad.

Aug 26, 2009 | 1994 GMC Jimmy

Not finding what you are looking for?
2000 Chevrolet Blazer Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...