Question about 1990 Dodge Dynasty

1 Answer

1990 Dodge Dynasty, has severe problems with the pulleys. Belt continues to slip off of the pulleys. Why does this little car have 5 pulleys and they don't do the same thing???

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 55 Answers

Make sure, with the belt off, that all the pully spin VERY freely. sounds like a component with a pully is locked up. good luck.

Posted on Jul 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the best way to fix my tensioner pulley it has a slant that causes the belt to slip


There's only one way too fix it and that's replacement of the pulley

Jan 10, 2014 | 1990 Dodge Dynasty

1 Answer

I have a dodge dynasty 1990 i replaced my serpentine belt now it wont stay on need to replace my tensioner pully how do i do it?


undo the big nut in front of the pulley. release the tension on the belt by adjusting the small bolt at the rear of the adjuster bracket . Take the nut of the shaft and pull the pulley off. Remember where the spacer goes at the back of the pulley.

Jan 10, 2014 | Hyundai Motor 2005 XG350

1 Answer

Serpintine belt will not stay on


Something is not turning correctly. Could be a water pump or a loose tensioner. Check to see if everything is easy to rotate...alternator, power steering pump, A/C pulley water pump. Do this with the belt off.

Jan 10, 2014 | 1990 Dodge Dynasty

1 Answer

1990 dodge Dynasty bad gas mileage and now cutting out real bad. Changed spark plug wires, spark plugs and fuel filter. Ran good for a test run right after installing items. This morning ran fine the 5...


May just be some dirty fuel, or clogged dirty air filter...try putting 2 bottles of fuel injector/carb cleaner in the tank to be sure dirty fuel has been treated. Did your Dynasty sit for a period of time? (Not driven or run for several months, or did you let the fuel tank get very low? Same remedy. Hope this helps..

May 23, 2012 | 1990 Dodge Dynasty

2 Answers

Dodge Dynasty 1990, 3.33 liter eng. The belt


Check to see if all your pulley's are aligned properly. It sounds like they may not be. Put the belt back on and look straight down it. If it appears to have a bend, that needs to be fixed. If you have a carpenter's square you can use it to double check you eye. You can use washers as shims on the bolts that hold whatever is out of line. If it sticks out too far you'll have to grind or file it to bring it back in line or remove washers or spacers if there are any. Hope this helps.

Oct 04, 2009 | 1990 Dodge Dynasty

1 Answer

My 1990 3.3 l dodge dynasty just all of the sudden stopped running. It really sounds like it isn't getting fuel. I am thinking the problem may be athe fuel pump. I tried to retrieve the check engine ...


to me it sounds more like the timing belt broke ...most of the time when a car with a timing belt at the age of your car suddenly just quits .....it turns out to be the timing belt...have it checked....btw your engine is a interference type engine which means the when the timing belt breaks it bends the valves...meaning a major repair

Sep 19, 2009 | 1990 Dodge Dynasty

1 Answer

Belt is to tight to put on


you may not have the right belt or you dont have the tensioner loosened enough

Sep 06, 2009 | 1990 Dodge Dynasty

1 Answer

Cant get old one off to replace it with the new one


Had the same problem, but it was the power steering pully, you have to get it from up under the car, it will be pretty hard to get the belt tensioner tool through there, but can't get it from up top.

Apr 22, 2009 | 1990 Dodge Dynasty

Not finding what you are looking for?
1990 Dodge Dynasty Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...