Question about 2000 GMC Sierra

1 Answer

LAUNCH SHUDDER. WILL A STRAIGHT PROPELLER SHAFT SOLVE THE ISSUE ON A EXTEND A CAB LONG BOX .THIS SHUDDER ALWAYS HAPPENS UNDER LOAD IE PULLING A TRAILOR OR A LOAD IN THE BOX. IT OCCASIONALY HAPPENS EMPTY AND WHILE AT HWY SPEEDS THANKS.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,088 Answers

I would be more inclined to look at the U-joints at either end of the drive line. Bent tubes usually cause vibration at speed. Jack up both rear wheels and put gearbox in neutral. Spin the wheels by hand and observe the drive line for being bent as it turns. A rare problem which allows the rear axle to twist under acceleration might be possible.

Posted on Jul 17, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1995 Lincoln Town car makes a rumbling noise underneath the seat when driving every so often


u-joint or carrier bearing or exhaust. Carrier bearing would be my guess

Mar 07, 2015 | Lincoln Cars & Trucks

1 Answer

How do i fix propeller shaft center bearing


Most center bearings require that you disassemble the center flex joint, then remove bearing from the shaft which on some requires use of a press or some type of puller.

Jan 01, 2015 | 2007 Nissan Frontier SE Crew Cab

1 Answer

Which fuse controls the horn in a 2002 silverado LT 1500 2wd ext cab pickup


Hello! In the under-hood junction box is a 15A fuse labeled "Horn Fuse"...Also in that box is the Horn Relay...If the fuse doesn't solve the problem listen for the relay clicking while someone presses the horn button...If the relay is not pulling I would suggest changing the relay...Guru...Saailer

Dec 25, 2010 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

Not sure how to remove a driveshaft from a 91 ext. cab mazda truck B2600


Welcome to FIxYa.com


REMOVAL AND INSTALLATION

Remove in the order shown in the figure. Install in the reverse order of removal.

I Image

1. Nut

2. Lock washer

3. Bolt

4. Nut

5. Nut

6. Lock washer

7. Bolt

8. Nut

9. Washer

lo. Nut

11. Lock washer

12. Bolt

13. Rear propeller shaft
leedavidian_15.pngleedavidian_16.pngleedavidian_17.pngleedavidian_18.png

Propeller shaft (4x2)

Before removing the propeller shaft, mark the flanges for correct installation.

Propeller shaft (4x4)

Before removing the propeller shaft mark on the front, and rear side flanges for correct

installation.

(4x2 Model)

When the propeller shaft is removed from the extension housing, immediately install the

SST into the extension housing to prevent oil leakage

B2200: 490259440

B2600i: 49 5120 440

1m a

Propeller shaft

1. Align the marks. And install the rear propeller shaft.

Tightening torque: 49-59 N.m (5.0-6.0 m-kg, 36-43 ft-lb)

2. Install the center bearing support assembly.

Tightening torque: 36-53 N.m 3.7-5.4 m-kg, 27-39 ft-lb)

3. Align the marks, and install the front propeller shaft.

Tightening torque: 49-59 N.m (5.0-6.0 m-kg, 36-43 ft-lb)


Thank you for using FixYa.com

Regards, Lee Davidian

Nov 05, 2010 | 1988 Mazda B2600 Cab Plus

1 Answer

1997 dodge ram 3500, it shudders in OD


Hey, I also have a 98 ram with the cummins and what you are talking about is when you are pullin hard in overdrive the trans is working to hard causing the shudder, when this happens back off the throttle and get back on the throttle to allow the trans to downshift. If you dont it will break the overdrive gear. There is nothing wrong with the trans it is just that it is shifting to early and bogging down causing the shudder.

May 18, 2010 | 1997 Dodge Ram 3500 Club Cab

1 Answer

Have a hard noise when i step out the acelerator, like in the trasfer or diferential.


Check out for the propeller shaft,check for the cross bearing of the propeller shaft,that make a very big noise like tak tak.........hope that clear your mind and solve.

Jan 16, 2010 | 2006 Ford F-150

1 Answer

2000 dodge dakota quad cab 4x4 v8 air conditioning set on max stops coming out of the vents when accelerating or pulling a load and feels like it loses power, it doesn't do it on the next lowest setting....


Sounds like you are losing too much vacuum under acceleration. Possibly a partially stopped up converter, or bad intake manifold gasket. Possibly a bad door actuator in the heater box also, and the loss of power would be a seperate issue.

Aug 12, 2009 | 2000 Dodge Dakota Quad Cab

Not finding what you are looking for?
2000 GMC Sierra Logo

Related Topics:

298 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...