Question about 1989 Isuzu Amigo

1 Answer

Need to find shreder valve - 1989 Isuzu Amigo

Posted by on

  • Colin Stickland
    Colin Stickland May 11, 2010

    what is this valve called in queens english please ---shredder?? schrouder?? treadle??

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 55 Answers

Looks like a tire valve. for fuel, its located on injector rail above intake. for a/c there are two, one big and one small, 1 @ COMP,& 1@ dryer.

Posted on Jul 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The Shreder will not shut off. It just keeps Running


paper caught in the "hey there is paper to shred " beam

need to clear it

or service the paper shredder

Jul 01, 2016 | Cars & Trucks

2 Answers

Need to adjust the valves on a 3.1 oldsmobile ciera.There is no mark on harmonic balancer.


there does not need to be marks on a harmonic balancer to adjust valves
when a piston is on tdc the valves will be either completely closed or in the valve rock position
when adjusting valve clearence you will need to know the firing order because when no 1 piston is ready to fire , then the next piston to fire will be in the valve rock position
for example if no1 piston of a 6 cylinder ( firing order 153642) is at tdc firing both valves will be closed and so the valves of no5 piston will be rocking so that will be the nect piston valves to adjust and after that no3 piston valves will rock so you do no 5 valves and so on
a workshop manual will explain it all to you

May 03, 2015 | 1996 Oldsmobile Cutlass Ciera

1 Answer

Is the TX valve the same as an expansion valve for a Toyota Camry 1994?


Yes, Thermal Xpansion valve. Failure can certainly involve sticking shut. Locations shown here, p8 and p53. The receiver drier would be routinely replaced if the TX valve had failed that way.

http://www.turboninjas.com/camry/ac.pdf


http://www.freeasestudyguides.com/ac-receiver-drier.html

Dec 16, 2012 | 1994 Toyota Camry

1 Answer

This nissan pickup was purchased at auction, #4 cyl. dead ran compression check 5 lbs. pressure, pulled head and found #4 exaust valve hadn't been closing for god knows how long, is there a lash setting or...


Valve might be bent , or valve guid too tight.
you need to ck if valve sliding free , fist.
if there is an adjustment needed on valves , all specs are on the hood lable.

Apr 16, 2010 | 1991 Nissan Pickup

1 Answer

3.2 liter yamaha engine manual IAC valve How do I replace the IAC valve on this engine? Steps? I just bought a new one and I need to get it replaced. FORD 1994 Taurus SHO 3.2 liter engine YAMAHA


may just need cleaning with carb cleaner.

here is 1996, oldest I have:

Section 03-14: Engine Controls, Electronic 1996 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Idle Air Control (IAC) Valve Removal
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Disconnect the engine control sensor wiring (12A581) from the idle air control valve (IAC valve) (9F715) at the idle air control valve electrical connector.
  1. Remove the two idle air control valve retaining bolts.
  1. Remove the idle air control valve and idle air control valve gasket.
Installation
  1. NOTE: If scraping is necessary, be careful not to damage idle air control valve gasket surfaces, or drop material into intake manifold (9424) or throttle body (9E926) (depending upon application).

    Clean idle air control valve gasket mating surfaces.
  1. To install idle air control valve, reverse Removal procedure.
  1. Tighten the idle air control valve retaining bolts to 8-12 Nm (71-106 lb-in).
33b4417.gif

Jan 14, 2010 | 1994 Ford Taurus

1 Answer

Is valve adjustments needed on 2000 camry V6 I am hearing noises that seems like coming from under valve cover, you can hear the noise from inside car,but not from outside of car. I was told this engine...


The valve adjustment usually isnt done unless there is valve noise. If you think its valve noise, have the dealer check it or a shop that does a LOT of Toyota work. Special tools and shims are needed to adjust the valves. Its a LOT of work and will not be cheap. You will want to replace the spark plugs at the same time.

Dec 01, 2009 | 2000 Toyota Camry

1 Answer

Want to locate pvc valve on 2000 pontiac grand am 6 cyl


You'll find the PCV valve on the right side of the front valve cover. You'll need to remove the valve in order to troubleshoot it to determine if you need a replacement. To remove, pull the PCV valve out of the cover and detach the hose

Test the old PCV valve to determine if it needs replacing. Blow air through it in order to see if it is clogged. If it does not seem to ventilate, then you'll need to install a new valve.

Pop the new PCV valve into the spot of the old valve. With the correct part, it should snap right in. Take the hose and reattach it in order to complete the installation.

Aug 21, 2009 | 2000 Pontiac Grand Am GT

1 Answer

Need a air brake diagram for a Ford L7000


96 F & B Series

Air Brake System, FT Series


b4c4ba6.gif
Item Part Number Description 1 2025 Front Brake Chamber 2 2A095 Quick Release Valve 3 2075 Compressor 4 2085 Governor 5 2A783 Tank Valve 6 2A550 Safety Valve 7 2063 Air Tank Reservoir 8 2A567 Drain **** 9 2B170 Single Check Valve 10 2K119 Double Check Valve 11 18737 Low Pressure Indicator 12 2A270 Foot Control Valve (E-7) 13 13480 Stoplamp Switch 14 2A662 Parking Brake Control Valve (PP-1) 15 2B280 Chassis Bulkhead Manifold 16 2B431 Inverting Relay Valve (R-7) 17 2A449 Relay Valve (R-12) 18 2225 Rear Brake Chamber A — 3/8-Inch Hose B — 1/4-Inch Hose C — 1/2-Inch Hose D — 5/8-Inch Hose

May 04, 2009 | Ford F Cars & Trucks

2 Answers

Need the valve gap for 1991 mighty max


Does not have adjustable valves . It has hydrolic valve lasher's . they are spring loaded ( i believe ) . I just replaced them in mine . valve giude seal's where worn out causing it to smoke realy bad ( looked like a mosqito truck ) and the valves where ticking , due to the hydrolic valve lash adjuster's being worn out . They are about $ 8 - 10 buck's each at advance .

Mar 22, 2009 | 1991 Mitsubishi Mighty Max

Not finding what you are looking for?

Open Questions:

Cars & Trucks Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...