Question about 1994 Jeep Grand Cherokee

1 Answer

How do I change the rear end on mine?? getting

How do I change the rear end on mine?? getting conflicting versions does the axel need removed

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 297 Answers

Not if you are replacing the whole rear end.

Posted on Jul 17, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace bearing in a 1991 chevy 1500 4x4 rear axel at driveshaft?


To replace pinon bearing you need to pull wheels and the brake drums off next pull cover off the back of the rear end (make sure you have a drain pan under rear end) next turn dive shaft till you see a small bolt remove bolt pull center pin out push axle in pull c clips out pull axels out remove four bolts holding ring and spider gears remove gears assembly next remove drive shaft remove bolt from pinon push pinon in remove seal and bearing

Jun 27, 2011 | 1991 Chevrolet K1500

1 Answer

I was going to replace a wheel brake cylinder on my rear axel. I thought I could just pull off the hub to get to the brake assembly but there is a bolted on cap and screwed on plate on the end of the...


Some cars/trucks have the hub mounted with screws/bolts. You will have to remove them to get the hub off. You may need a rubber mallet to beat on the hub a little to get it to come off past the groove the brake pads may have made in the hub. After you get the hub off, take a picture of the brake components so you will know where everything goes once you start removing parts. Once you remove the springs, stuff will shift around and fall out on you so be careful and try to notice where everything goes as it is removed. If you run into problems during reassembly, you can always remove the hub on the other side to get pointers on where everything should go. Good luck.

Oct 11, 2010 | Dodge Ram 2500 Cars & Trucks

1 Answer

Hello.... I hear some big noise in the rear axle (differential);so i have to change it,but only found the rear axle of a L300 petrol one,when mine is a diesel.So, are rear axles Mitsubishi L 300 gasoline...


While I am uncertain, sadly no diesel here in the USA (danged EPA) I would expectthe diesel rear axel to have a different ratio from the gasoline, as the diesels run slower. You should be able to manually turn the yoke on the rear-end and count the revolutions for the axel to make one full revolution. With this you will be able to determine the rear-eand gear ratios.

Best of luck!
Tom

Jun 27, 2010 | 1990 Mitsubishi Minivan

1 Answer

How to replace rear axle seals


if the seal (s) is leaking you may have a bad bearing... to change.. remove the rear end cover, reach in pull the c clip on left or rt side. pull the axel out the side, use bearing puller to pull the old bearing, install new replacement bearing seal, put in axel, replace clip, reinstall rear cover, sealing properly, fill with rear gear lube to level of fill hole. get a chiltons manual for pictures and more detailed help.

Mar 10, 2010 | 1987 Chevrolet Caprice

1 Answer

How to remove rear axle 03 chevy silverado


You will have to remove the rear end plate off of the back of the rear end. Then turn the carrier untill you see a big silver pin that goes through the spider gears. Those will be 4 small gears in the rear end carrier. If you look at the right side of the carrier were the pin goes through it you will see a small bolt head, That bolt goes through the carrier and holds the pin in place. Remove that bolt then reach up in the rear end housing and push the pin towards you untill it comes out. ( DO NOT TURN ANYTHING AFTER YOU REMOVE THE PIN) are the spider gears will fall out.


Now get someone to push the axel in while you are looking at the 4 small gears in the housing, when they push the axel in a C-clip will fall off the end of the axel and into the rear end, You will see it fall out. Then just pull the axel out.



When you put the axel back in, push it all the way in then slide the c-clip over the end of the axel and then pull out on axel and that will hold the clip in place untill you put the big long pin back in the carrier. I hope you understand, just watch what you are doing. GOOD LUCK.

Oct 09, 2009 | 2003 GMC Yukon

1 Answer

How to remove rear axles on 90 gmc s15 to replace axle seals


You take off the differential cover in the middle of the rear end and theres a lock you slide out on both sides inside the rear end on the side walls each rear axel on both sides has one. Take them out and the axels will slide out.

Oct 04, 2009 | 1988 GMC S-15

1 Answer

How to replace my 1994 lincoln towncar rear axel seal


you need to pull the cover off the rear diff. remove the rear brake drums or rotors, remove the bolt that holds the pin in the rear end, remove the pin, remoce the c clips, pull the axles out. remove the seal. you can do this by using one ofthe axles to pry the seal out. install the new seal and reassemble. use rtv sealant to reseal rear diff and fill with about 3 - 3 1/2 qts gear lube-may take synthetic

May 23, 2009 | 1994 Lincoln Town Car

1 Answer

Rear Axel Seal


Wheel, brakes etc that are in way of pulling axle out have to come off. Drain rear end fluid, remove rear housing cover, remove bolt that holds pin in differential, remove differential pin, push in slightly on axle to remove "U" clip that holds shaft in, then slide shaft out. replace seal. Reverse procedure for re-install & fill with gear lube. If any questions, get back to us.

Apr 16, 2009 | 2002 Ford Mustang

1 Answer

85 cj7 rear axle removal


Do you have bolt in axels? or are they held in with C- clips? If its bolt in axels you need to remove the bolts, and you may need an axel puller to get them out. If its got C- clips rear cover on rearend has to come off, and pin has to be removed to get C- clip out to get axel out.

Apr 03, 2009 | 1986 Jeep CJ7

1 Answer

Rear axle seal replacement


Drain axel of Fluid, Roemve Diff Cover (Push IN on Axel to reseal at Wheel side) Remove KEEPERS From Insied END of axel then Pull OUT on WHEEL END of Axel. use Proper Seal removal tool to remove seal. Also Use PROPER Install tool for SEAL INSTALL Reverse Procedure to Install. In hopes this helps you Out.
Please RATE Me Also LoL Thank You.

Mar 24, 2009 | 1999 Ford F150 Regular Cab

Not finding what you are looking for?
1994 Jeep Grand Cherokee Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...