Question about 2005 Mitsubishi Lancer Evolution

1 Answer

Do you have to remove the subframe ain order to get the tansmission out to reeplace the clutch?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 850 Answers

The cross member can be lowered if there is enough room then just slide the box back so you ca get to the bolts otherwise remove it

Posted on Jul 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to remove the oil pan easy and safe from a 2005 crv honda


Hi Evelyn.here's a link on your oil pan removal,it says engine removal,will send a link on that too. SAVE 20 ON ONLINE SHIP TO HOME ORDERS OF 100 OR MORE Here's the engine removal guide. SAVE 20 ON ONLINE SHIP TO HOME ORDERS OF 100 OR MORE

May 17, 2015 | 2005 Honda CR-V

1 Answer

How to remove 2006 ford focus zx4 manual transmission


  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    Steering column shaft bolt Battery and tray Air intake assembly Resonator Gearshift cables from the transaxle Gearshift cables from the bracket Hydraulic clutch line from retaining bracket Heated Oxygen Sensors (HO2S) and Catalyst Monitor Sensor (CMS) connections
  3. Support the engine using Special Tools 303-290.
  4. Remove or disconnect the following:
    NOTE Matchmark the subframe to the chassis.


    Rear engine mount and mount bracket Reverse lamp switch Upper transmission to engine bolts Tire and wheels Engine roll restrictor Tie rods from the knuckles Lower control arms from the wheel knuckles Stabilizer bar from the strut Power steering lines from the steering gear
  5. Support the subframe with a suitable lifting device.
  6. Remove the six subframe bolts and lower the subframe from the vehicle.
  7. Remove or disconnect the following:

    Vehicle Speed Sensor (VSS) Right hand halfshaft from the transmission and hang securely aside Left hand halfshaft from the transmission and hang securely aside
  8. Loosen, but do not remove, the starter mounting bolts
  9. Disconnect the clutch hydraulic line.
  10. Secure the transmission to a jack or suitable lifting device.
  11. Remove the 10 transmission-to-engine bolts.
  12. Pull the transmission rearward until the input shaft is clear of the pressure plate, then lower the transmission from the vehicle.

    0996b43f80201168.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Supporting the engine with Engine Support 303-290.

Jan 25, 2011 | 2006 Ford Focus

1 Answer

How do you remove transmition?? Do you have to compleatly remove the subframe??


yes and in order to remove subframe you need a engine cradle bar to that attaches to the engine under the hood and rests on shock towers and front of radiator holds the engine in place for subframe and trans removal. this is a very laboress job. good luck

Feb 10, 2010 | 2004 Ford Freestar

2 Answers

I need to replace the clutch in my s4 convertible 2004 where do you start to strip her down and how long should it take


This is a complex question. I'm not familiar with the s4. Is it front wheel drive or rear wheel? do you have access to a hoist or is this an on the ground project? An experienced shop could have this done in a day... provided they have a hoist open. I would imagine if this is your first time it's going to be a couple of days. If this is front wheel drive most of them have a subframe that comes off first, it's going to be a real pain if you don't have a hoist and a transmission jack. Can it be done on the floor, you bet, but I wouldn't do it and I've put in hundreds of transmissions.

Nov 09, 2009 | 2004 Audi S4

1 Answer

Need to replace clutch. bought the parts.


ok this is involved here,,,if youre doing it on the floor you gonna have a harder time,,,there is 2 ways to do this the first gives you more room to swap the clutch but you remove more stuff to gain that extra room,meaning more time,,,,the second is the way i would do it,,,remove the battery and tray,remove the top trans bolts and connectors etc, remove wheels and drivers side axle,you can remove the passenger side axle if you wish,it makes it easier if youre a first timer,,,go under car remove exhaust bolts from where header meets pipe,3, nuts, 13mm header,remove top trans mount and lower trans mount and loosen the passenger side subframe bolts 18mm and take out the 2 drivefrs side subframe bolt,BEFORE you do this suport the engine somehow either with chain and bar from top or jack under it,,the jack sucks as it gets in yuor way,,then slide the trans off the engine over to the side and it should kinda tuck in there you might have to strap it there while you swap the clutch,,,ALSO remove the reverse light switch first so you dont break it trying to tuck the trans aside,,then swap the clutch,,,this is the quicker way but tighter and harder if you dont know what is going on,,the other way is all the same but you remove the lower subframe completely from the car,,this requiresm more work,,,,steering shaft bolt removal,,,lower control arm nuts,etc,you choose

Oct 12, 2009 | 1998 Saturn SL

1 Answer

How to reeplace clutch in a mazda 6 4 cyl


remove the transmission housing from the engine you will see the clutch housing from there.

Sep 17, 2009 | 2003 Mazda Mazda6

1 Answer

How do i remove the transmission in my 95 geo prizm


This requires a boom which is a mounting brace which that holds the engine in place (from the top) as you drop the lower subframe in order to remove the transmission. Once the boom is in place and hooked to the engine,lift and remove wheels,exhaust,lower control arm,axles,subframe and finally the transmission. .

Aug 23, 2009 | 1995 Geo Prizm

1 Answer

Blwr. mtr. fuse blows when a/c is turned on


May check your A/C Diode for failure.Hope this helps

May 16, 2009 | 1995 Ford Contour

1 Answer

Clutch


Yes unfortunately the engine has to be supported with a support bar from the top,subframe has to come out, and transmission comes out thru the bottom.

Feb 09, 2009 | 2008 Ford Fusion

1 Answer

High reving to get the car moving


UNFORTUATELY ITS NOT A EASY JOB TO DO AS YOU HAVE TO REMOVE SUBFRAME TO GET GEARBOX OUT & PUTTING GEARBOX & SUBFRAME IN YOU NEED LINING UP TOOL FOR SUBFRAME.YOU ALSO NEED ACCESS TO A TWO POST RAMP HOPE THIS HELPS YOU.

Feb 09, 2009 | 2000 Ford Escort

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...