Question about 1993 Chevrolet Beretta

1 Answer

Racecar Motor Bogging on Acceleration

I have a 1995 Chevy Beretta with a 2.2 litre that I race at my local circle track. Complete engine rebuild.Shaved deck.New head.Performance cam and pistons etc.
New TPS and cable.New O2 sensor.New coil packs, plugs and wires.New MAT sensor.

Occasionally no power to start, will start when crossing starter. Think that is the Neutral start switch. Can you confirm though?
Bogging on acceleration. This is the real issue. I will get about half way to to the floor and it will start sputtering. Also, the first spark plug on the left looks like it is getting enough fuel, but they degrade from there. By the third plug, it looks very lean.

Engine idles like a champ in park and neutral. It has the power to do what I want it to, just need to get the acceleration issue fixed.

Any ideas? Thanks! Mary Gregory

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 850 Answers

Try checking fuel pump presure & delivery
id say its starving or has a blockage
im in AUSTARLIA mate so i dont know the engine but doesnt matterif its efi you may need bigger injectors aswell
if carbs try re jetting

Posted on Jul 17, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Where is the drain plug located on a 1995 chevy beretta 3.1 liter?

Radiator is on the drivers side in front of the radiator(White). Oil pan is on the back side of the pan in the middle. Not one for the transmission.

Nov 29, 2015 | Cars & Trucks

1 Answer

How many quarts of oil does a 1990 chevy beretta 3.1ltr take

these hold 5 litres of oil with a filter change. as far as quarts it will be a minimum of 4 run engine for a bit then shut off and check level.

Sep 21, 2014 | 1990 Chevrolet Beretta

2 Answers

How do i put a water pump in a 95 chevy beretta

I put a new waterpump on my 95 Beretta. Actually, it isnt that hard. I followed this video on youtube & had no problems. Hope this helped. Just realized this post is like 2 years old. duhhh,,,,

Dec 08, 2010 | 1995 Chevrolet Beretta

1 Answer

Location of fan relay 1995 chevy baretta

usually in relay box, engine compartment--near battery. if not there, please get back to me and I'll try to track it down.

Sep 24, 2010 | 1995 Chevrolet Beretta

1 Answer

Is there a parts list anywhere for rear brakes for a 1995 chevy beretta

The rear brakes consist of
  1. Drum
  2. Wheel cylinder
  3. Brake Shoes
which you have to get separately at your local part store. The other components can be obtained by purchasing a hardware kit. Which contains springs, keepers, pins....ext One kit contains this hardware for both sides of the rear brake system.

Jul 11, 2010 | 1995 Chevrolet Beretta

1 Answer

86 4.3 litre V6 chevy el camino bogging down, stalling out

most likely a weak fuel pump or a clogged filter. Check fuel pressure with a gauge or as its bogging down spray brake cleaner in the Throttle Body. If this allows it to increase RPM then its the pump or filter.

Oct 30, 2009 | 1986 Chevrolet El Camino

1 Answer

I need to get a new pcv elbow connector for 95 chevy beretta v6

I have taken a spark plug boot of of a 90 degree boot of the wire and use this it works so check the junk yard for a plug wire with a 90 degree boot on it and pull it off the wire :)

Sep 29, 2009 | 1995 Chevrolet Beretta

1 Answer

3.1l motor swap

if it is the same motor going in that came out ,it would fit and hook up but if you are changing from one size to another, you will have to change the wiring harness, hope this helps you, thanks robert b.

Jun 27, 2009 | 1995 Chevrolet Beretta

Not finding what you are looking for?
1993 Chevrolet Beretta Logo

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

77544 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides