Question about 2004 Hyundai Santa Fe

1 Answer

Rear view mirror needs tightening

Got a bluetooth rearview mirror which attaches to the present mirror but too heavy which causes the mirror to fall. Any way to tighten. 2003 Mitsubishi Eclipse Spyder convertible so the rearview mirror is attached to windshield. Thanks for any help! Also same problem with 2007 Pontiac Solstice convertible....

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 123 Answers

Go to a workshop

Posted on Jul 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My rear view mirror camera quit working I checked the fuse it's good the backup lights work.Help


Circuit/System Description
When the transmission is placed into REVERSE, a 12 volt signal is sent to the rearview camera image display module indicating that camera operation is requested. The rearview camera image display module then supplies ignition voltage and ground to the rear vision camera. The rear vision camera sends video information through the rearview camera image display module to the inside rearview mirror through a video signal + and a video signal - circuit. A grounded shielding also wraps the video signal circuits to reduce electronic interference which may degrade the video signal and cause a distorted or otherwise degraded image.

Rearview Camera Image Display Module (UVC)
In the instrument panel behind the driver side knee bolster to the right of the steering column
Do you know how to do electrical testing ?

Rear Vision Camera System Does Not Display
Ignition OFF, disconnect the harness connector at the rear view camera image display module.
Test for less than 1.0 ohm between the ground circuit terminal 3 and ground.
? If greater than the specified range, test the ground circuit for an open/high resistance.
Ignition ON, verify that a test lamp illuminates between the ignition circuit terminal 2 and ground.
? If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.
Ignition ON, park brake applied, vehicle in REVERSE, verify that a test lamp illuminates between the control circuit terminal 1 and ground.
? If the test lamp does not illuminate, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.
Ignition OFF, connect the harness connector at the rear view camera image display module. Disconnect the harness connector at the rearview camera.
Ignition OFF, test for less than 1.0 ohm between the ground circuit terminal B and ground.
? If greater than the specified range, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the rear view camera image display module.
Ignition ON, park brake applied, vehicle in REVERSE, test for 5.8-6.2 volts between the 6-volt reference circuit terminal A and ground.
? If less than the specified range, test the 6-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the rear view camera image display module.
? If greater than the specified range, test the 6-volt reference circuit for a short to voltage. If the circuit tests normal, replace the rear view camera image display module.
Ignition OFF, disconnect the harness connector at the rear view camera image display module.
Test for less then 1 ohm between the shield ground circuit terminal 10 at the rear vision camera display module harness connector and terminal D at the rear vision camera harness connector.
? If greater than the specified range, test the shield ground circuit for an open/high resistance.
Ignition ON, test for less than 1 volt between the signal circuit terminal 9 and ground.
? If greater than the specified range, test the signal circuit for a short to voltage.
Test for infinite resistance between the signal circuit terminal 9 and ground.
? If not the specified value, test the signal circuit for a short to ground.
Test for less then 1 ohm between the signal circuit terminal 9 at the rear vision camera display module harness connector and terminal C at the rear vision camera harness connector.
? If greater than the specified range, test the signal circuit for an open/high resistance.
Ignition OFF, disconnect the harness connector at the inside rearview mirror.
Ignition ON, test for less than 1 volt between the following signal circuits at the inside rearview mirror harness connector and ground:
• Video + signal circuit terminal 6
• Video - signal circuit terminal 7
Test for infinite resistance between the following signal circuits at the inside rearview mirror harness connector and ground:
? If greater than the specified range, test the signal circuit for a short to voltage.
• Video + signal circuit terminal 6
• Video - signal circuit terminal 7
? If greater than the specified value, test the signal circuit for a short to ground.
Test for less then 1 ohm between the following signal circuits:
• Signal circuit terminal 12 at the rearview camera image module and terminal 6 at the inside rearview mirror.
• Signal circuit terminal 11 at the rearview camera image module and terminal 7 at the inside rearview mirror.
? If greater than the specified range, test the signal circuit for an open/high resistance.
If all circuits test normal, test or replace the rear vision camera.
Ignition ON, park brake applied, vehicle in REVERSE, verify a clear rear vision image is displayed on the radio.
? If a clear rear vision image is not displayed, test or replace the inside rearview mirror

Feb 21, 2016 | 2009 Hummer H3

1 Answer

Automatic rear view mirror not working when lights approach from rear


Troubleshooting Your Auto-Dimming Rear View Mirror ...

www.doityourself.com/.../troubleshooting-your-autodimming-rear-view-...
An auto-dimming rear view mirror is a great convenience when there is too much lighton the mirror. This is not only good for you as the driver, but also for ...

How To Fix Malfunctioning Rearview Mirrors - YouTube

? 5:58
https://www.youtube.com/watch?v=gz1aVM7WeQM
Sep 20, 2012 - Uploaded by iggy151
This is a short and dirty video describing how to repair rearview ... electrical malfunctions such as nonworking or ...

Dec 20, 2015 | Cars & Trucks

1 Answer

Rear view mirror on front windscreen keeps falling off - hangs and swings - dangerous


Might I suggest :Permatex Professional Strength Rearview Mirror Adhesive permanently remounts your mirror to your windshield.
Special glue you may need to clean glass w razor and alchohol
But this should fix the problem

gl the ed

Mar 12, 2015 | Cars & Trucks

1 Answer

How to reattach rearview mirror


Try holding the mirror firmly in the middle and pressing the cup back over the ball. It it falls of again then check that the cup section has not split.

Aug 06, 2014 | 2004 Buick Rendezvous

1 Answer

2012 hyundai tucson setting the garage door opener that is located in rear view mirror


Thanks filter4991;
1. Press and hold button on car's rearview mirror
2. Press and hold button on garage door opener's remote control.
3. Light on Rearview mirror will flash rapidly.
4. Release both buttons.
5. Locate learning button on garage door opener (generally this can be found by tracing the antennae to where it is attached to the unit.)
6. Press and release "Learning button"
7. Press and release rearview mirror button repeatedly until garage door opens/closes but it should work the first or second time.

Worked on Genie Intellicode and Hyundai Tuscon

Sep 20, 2012 | Hyundai Tucson Cars & Trucks

2 Answers

How do I reattach the rearview mirror?


there is a glue you can buy at auto-zone,and they may have a kit.

Aug 29, 2010 | 1996 Chevrolet Cavalier

1 Answer

Seperate rearview mirror from plate both came off


f

Replacing the rear view mirror on a Ford Explorer is easy. The only obstacle you might encounter is fear of breaking the glued metal plate off the windshield. Do not sweat it. You can buy glues at the auto parts store to reattach the mirror to the windshield (Difficulty: Moderately Easy).

Instructions:
  1. Tap gently at the base of the mirror where it slides on over the metal plate glued to the windshield and pull upward. Some rear view mirrors have a small Allen screw that tightens the base of the rear view mirror to the metal plate. Disconnect the electrical plugs if your rear view mirror has them.
  2. Pull the rear view mirror clear of the metal plate. Clean around the metal plate glued to the windshield. If the metal plate has come off because of harsh weather or from hammering too hard at it, reattach it with glue designed for this job.
  3. Clean the area where you will be attaching the metal plate on the windshield. Apply the glue evenly on the surface of the metal plate that will go against the window. Be sure to clean and scrape off all the old glue before applying the new glue. Gently push the metal plate against the windshield in the spot you wanted it and hold tight for five minutes.
  4. Wait a day before putting the base of the mirror or replacement rear view mirror onto the metal plate. Do not force the base over the plate. Forcing it will likely dislodge it again. Press firmly until it will not slide along the grooves of the metal plate. Reconnect your electrical plugs and tighten the Allen screw if your new mirror has one. Adjust the mirror according to your safe viewing preference

Hope help with this (remember rated this help). Good luck.

Mar 12, 2010 | 1999 Ford Explorer

1 Answer

Rearview mirror on a 1998 ford exployer


o to the auto parts store and buy a rear view mirror ask them for the rearview mirror adhesive and on the back of the package it tells you how to use it.its not very hard to do and isntexpensive to buy. takes about 15 minutes

Jan 18, 2009 | 1998 Ford Explorer

1 Answer

2008 cobalt s/s Turbo rear view mirror


There should be a set screw which is usually a small recessed hex head. a set of small allen wrenches will do the trick. It may also be a torx style screw. Just look carefully and you can fix this easily.

Sep 29, 2008 | 2006 Chevrolet Cobalt

Not finding what you are looking for?
2004 Hyundai Santa Fe Logo

720 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...