Question about 1996 Toyota Camry

1 Answer

Head gasket on the 1996 4 cyl toyota camry

Is it difficult to change the head gasket on the 1996 2200 4 cyl toyota camry. One cylinder is full of radiator fluid. I only have concerns about the overhead cam

Posted by on

  • tonissoo Jul 17, 2009

    I was going to take the head off and possibly have it machined and replace the head gasket myself at home. I have done this for falcons but the overhead cam worries me. Not sure if the are cam chains or other parts that need special alignent when replaced.

  • yadayada
    yadayada May 11, 2010

    I don't understand the question here.

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 34 Answers

Go to the library and borrow a manual its not a very hard job but you will need a manual.

Posted on Jul 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace cylinder head on 1996 RAV4


William, Could not a lot on your particular engine, links below to show the basics on removal/install of cylinder head. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
TOYOTA AVENSIS ENGINE REPAIR BLOWN HEAD GASKIT
How to replace the cylinder head gasket on 96 Toyota Camry 4 cylinder
Replacing the head of VVTI celica engine 2000 2005


Jul 09, 2016 | 1996 Toyota RAV4

1 Answer

How to torque cylinder head bolts


Assuming it is a 4-cyl, see here, p40

http://www.turboninjas.com/camry/eg1.pdf

Jun 26, 2014 | 1996 Toyota Camry

1 Answer

Whats the firing order on a 1997 toyota camery 2200 4 cy


Hi Steph ! Since is a 4 (FOUR ) cylinder engine the firing order is 1342.

Mar 18, 2014 | 1996 Toyota Camry

1 Answer

I need how much torque the head bolts for toyota camry 1996


It is 36 ft-lb, but done in two stages to a prescribed sequence.The bolts should be oiled. See here p67

http://www.turboninjas.com/camry/eg1.pdf


This is for the 4-cyl. The V6 is 40 ft-lb, and the link is .....eg2.pdf.

Aug 13, 2012 | 1996 Toyota Camry

1 Answer

Changed cyl head, on 1996 2.2 toyota camry, cant seem to figure out cam timing


there is a hole in the camshaft gear turn the gear until it lines up with a mark in the cylinder head at the top. then line the crankshaft gear mark up with the mark on the block. sometimes the best way to see the camshaft timing mark is with a mirror.

Aug 16, 2011 | 1996 Toyota Camry

1 Answer

How to change head gasket on 1996 camry


How to change head gasket camry 1996

Mar 12, 2011 | 1996 Toyota Camry

1 Answer

#4 cylinder on my 2.2L camry has no compression.


The head gasket might be bad around that cylinder, or the piston rings are worn and not holding the compression.

Jan 08, 2010 | 1996 Toyota Camry

2 Answers

Found a car but needs work add says:toyota camry 6 cylinder


do a compression test on it first and find out if it is down on compression

May 05, 2009 | 1996 Toyota Camry

2 Answers

95 camry won`t start


Have the head gasket torqued to 60psi each bolt? if so, either the spark plug grooves got a crack, or the head is bent due to a past overheat... or overheats. If so, send the head to a machine shop and have it leveled out, and replace all gaskets replaced when putting back on. That includes, manifold, header, and head gaskets, as well as the oil seals and O-rings. Hope this will help you.

Aug 14, 2008 | 1995 Toyota Camry

Not finding what you are looking for?
1996 Toyota Camry Logo

Related Topics:

1,016 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...