Question about 1998 GMC Jimmy

1 Answer

Wipers quit working how does the actuator actually work at the switch

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 34 Answers

Not sure of the question but wipers not working is commonly the wiper board mounted right on the wiper motor.

Posted on Jul 17, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I put a new wiper motor on a 79 el camino and it works but it dont move the wipers it just turns and i got the 2 nuts tite on the wiper transmission


Check to make sure that the "Knurled" segments on the tapered points that hold the wiper arms to the motor actuators are not worn smooth as this is what gives the actual grip required for the wiper movement. If they are worn smooth then no amount of tightening will help.

Apr 07, 2017 | Chevrolet El Camino Cars & Trucks

1 Answer

Wiper switch


if wipers dont work at all try the fuse first.. the actual switch is on the steering column at the base of the actuator..it requires removal of the cover over the steering column..

Dec 08, 2013 | Cars & Trucks

1 Answer

Wipers not working


Could be a relay. Look at your wiring diagram. Swap relay with one of the same number, see if it cures the problem.

Apr 08, 2017 | 1994 Chevrolet Silverado 2500

1 Answer

The wipers quit on my 06 cruiser. they had been coming on and off by themselves for a while and then just quit. the back wipers work fine.


if power to wiper motor, then replace the wiper motor. if no power when switch is on, it is most likely the wiper switch thats bad. check the relays and fuses first! good-day!

Aug 22, 2011 | 2006 Chrysler PT Cruiser

1 Answer

Windshield Wipers on 2007 Altima Quit on High


It might be either switch itself or wiper relay.
Ufortunatly I don't know location of the relay.
You can actually find relay by noise , put the switch on intermittent position and see where the cliking coming from.

Jun 30, 2010 | 2007 Nissan Altima 3.5 Sedan

1 Answer

My air conditioner is working but won't blow out


Are you saying the temp blend door is not working?
If yes, it's the control head or the temp blend door motor on th plenum case under the dash. Buy used on ebay.

DO you have manaul or electroic controls?

If electronic

A/C Electronic Blend Door Actuator The A/C electronic blend door actuator is located on top of the A/C evaporator core housing (19A553) assembly.
  • Its function is to move the A/C air temperature control door on command from the control assembly.
  • The A/C electronic blend door actuator contains a reversible electric motor and a potentiometer. The potentiometer wiper is connected to the actuator output shaft and moves with the output shaft to indicate the position of the A/C air temperature control door.
  • A five volt signal is applied to the ends of the potentiometer. The voltage available at the wiper indicates the position of the potentiometer. The expressed value of the actuator wiper voltage is sent to the control module and matched with the wiper voltage of the module potentiometer. The printed circuit board then drives the actuator motor in whichever direction is necessary to make the actuator wiper voltage agree with the control module wiper voltage.
-----------------------------------------------------------
manual

#3 is the blend door.

0425af0.gif

May 08, 2010 | 1998 Mercury Grand Marquis

1 Answer

My wiper motor started working intermittently. Then it quit all together. I had a new switch put in and it still did not work. I then had a wiper motor put in and it worked for 2 weeks. It quit working...


It's probably a bad ground, clean the plug or drill a screw into the frame and connect it with a wire and another screw into the actual wiper box where it won't interfere with the motor.

Apr 25, 2010 | 1993 Mazda Protege

1 Answer

WINDSHIELD WIPERS QUIT WORKING


It could be as simple as a blown fuse. Other problems involve wiring, switch, wiper motor. It needs to be checked by someone who understands wiring diagrams and follows it. Good luck!!!

Oct 12, 2009 | 2002 Hyundai Santa Fe

Not finding what you are looking for?
1998 GMC Jimmy Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...