Question about 2004 Ford F150

3 Answers

F150 stalls out at intersections.

I have a F150 FX4 and it stalls out when i coast into a stoplight or stop sign. It has done it on several ocassions and the mass airflow sensor was just replaced. It has done it once this this maintenance was performed.

Posted by on

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 59 Answers

Clean the throttle body and idle air control valve unless the valve has a plastic body which should be replaced because the harsh cleaner would damage it. If the idle air valve has a metal body you can clean it. Also you may want to check and or clean you EGR valve they are also known to build carbon and cause internal vacuum leaks causing a low idle stall

Posted on Jul 18, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,674 Answers

I'd remove the idle air control valve & clean it & port it comes out of with throttle body spray cleaner, or carburetor cleaner, and try that. If it cures it, then later start to do it again, replace it.

Posted on Jul 17, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 534 Answers

Check there are no air leaks on the air intake system. - check all the clamps/hoses etc that may have been removed to replace airflow sensor.

Posted on Jul 17, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why would my car stall out when stepping on brakes but only sometimes?


Probably a vacuum leak. While driving you get additional air flow to the intake, but at a stop the intake is deprived of air because of an air leak. Check your air inlet hoses.

Feb 08, 2016 | 2000 Pontiac Sunfire

1 Answer

Stalling for a few seconds when leaving a stop sign. This is an intermittent problem. Seems to happen most of the time when turning left when leaving a stop sign. Stalling also happens when rolling slow at...


Is the brake fluid reservoir low? The master brake cylinder may be leaking, the fluid getting sucked into the brakes power booster and then into the vacuum of the intake manifold. Check the vaccuum hose to the brakes power booster to see if it is wet inside with brake fluid.

Mar 14, 2015 | 2014 Hyundai Santa Fe

1 Answer

Car stalls at intersections and stops had coils


check idle control valve / sensor may need replacement

Nov 03, 2009 | 2003 Kia Sedona

1 Answer

Cars stalls at stop light


timing belt idel spring could be bad

Aug 11, 2009 | 1997 Mercury Mountaineer

1 Answer

2004 fx4 4x4 f 150 trans fault code hi temp


hi there. ...i can advise you that i have replaceed several transmission fluid temperature sensors (tft) for faulty readings.it is inside transmission and can be accessed by removing pan...hope this helps!...good luck

Jun 04, 2009 | 2004 Ford F150

2 Answers

3.1 V6 engine stalls when coasting to a stop sign


YOUR TORQUE CONVERTOR CLUTCH (TCC)SOLENOID IS STICKING IN THE ON POSITION. GET IT REPLACED AND YOU WILL BE FINE.

May 18, 2009 | 1993 Chevrolet Lumina

1 Answer

Ford F150 FX4 2004 Front Hub Noise


have your cv shat checked or changed, those clunking noise is a sign of "constant velocity"CV joint failure, sometimes the noise stops because it is caused by damaged bearings. you should have it checked or changed before it fails on you, once this happens you will not be able to move your vehicle unless towed.

Mar 20, 2009 | 2004 Ford F150

Not finding what you are looking for?
2004 Ford F150 Logo

1,093 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...