Question about 2000 Chevrolet Blazer

1 Answer

Torc specifications for 2000 chevy blazerfor the intake manifold gasket

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 34 Answers

Do it in three passes 1st pass 27 inch pounds 2nd pass 106 inch pounds 3rd and final pass (carefull it changes up on ya a bit) 11 foot pounds.

Posted on Jul 17, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 chevy blazer stalls when accelerating


you may have put the gasket on incorrectly and its lacking air ???

Jan 17, 2014 | Chevrolet Blazer Cars & Trucks

1 Answer

Want crank 2000 blazer


2000 Chevy blazer doesn't have a carburetor. It's multiport/sequential port fuel injected. Your injectors look like a spider inside the intake manifold. If they are not delivering fuel, that assembly needs to be replaced. That's a pretty big deal. Need to replace a few other gaskets as well since other components will be pulled.

Dec 31, 2012 | Cars & Trucks

1 Answer

2000 chevy v-6 4.3 torque sequence and settings for intake manifold


lower intake manifold

step 1 27 inch lbs.

step 2 106 inch lbs.

step 3 134 inch lbs.



johnjnail_54.jpg
upper intake manifold

step 1 44 inch lbs.

step 2 80 inch lbs.

Jun 01, 2011 | 2000 Chevrolet Blazer

1 Answer

I HAVE ANITFREEZE LEAKS FROM MY 2000 CHEVY S10 BLAZER. IT'S HARD TO TELL BUT THE LEAK SEEMS TO BE COMING FROM UNDER THE MOTOR RATHER THAN FROM THE RADIATOR OR ANY HOSE I CAN SEE.


a common V6 failure is the intake manifold gasket. coolant will usually leak behind the water pump on the drivers side, however it can leak at other locations on the intake manifold gasket.

coolant leaks from other areas include the heater core, hoses, expansion plugs, trans cooler, and coolant overflow tank.

Jan 03, 2011 | 2000 Chevrolet Blazer

1 Answer

I have a 1997 Chevy Blazer that is overheating and is leaking coolant. It is not the rad hose because I have already checked that. It is a part that is attached to the engine block, directly above the...


Ihave a 96 s10 lt blazer First of all the steering coloum is now where near the engine block and the bracket you mention is for the throttle cable and the cruise control cable and has no gasket for any kind of a seal with the intake manifold. The 4.3 and most chevy engines have a problem with the intake manifold gaskets if you are over heating then likely the intake manifold gasket is leaking you should check your engine oil for antifreeze that will look like a fomey white yellowey residue and also check the radiator for engine oil floating on the top under the radiator cap. This is a big problem with chevy you can't let espesecly the 4.3 ever over heat.There is olny 8 bolts that hold the manifold to the block and there all in the four corners nun in the middle Y ou can save the engine if you fix it now but it is the intake manifold gasket that is leaking

Dec 12, 2010 | 1997 Chevrolet Blazer

1 Answer

What is the torque specifications and sequencing for the intake manifold on a 1998 Chevy blazer?


zjlimited_198.jpg

Fig. 1: Intake manifold installation-4.3L engines (click over image for zoom)


zjlimited_200.jpg

Fig. 2: Intake manifold bolt tightening sequence-1996-98 4.3L engines

Install the bolts and tighten in sequence and in 3 steps as follows:

  1. First step to 26 inch lbs. (3 Nm).
  2. Second step to 106 inch lbs. (12 Nm).
  3. Final step to 11 ft. lbs. (15 Nm).

Hope this helps (remember to rate this answer). Good luck.

Dec 08, 2010 | 1998 Chevrolet Blazer

1 Answer

Just replaced intake manifold gasket on 2000 Chevy Blazer and now truck wont start


hi, its sounds to me like the gasket could have been faulty unless a wire has come off or not fitted properly,

Check for loose wires or connectors with no wires going to them and fit these wires back on check the fuel line has not split, check the bolts are tightened properly.

Try turning it over a few times in case its a fuel pressure problem if after doing this its still dont start then you need to take the manifold off and check the gasket is fitted properly as it may have slipped and not be sealing properly, once you have done this refit and tighten then let me know what happens ok.

Let me know how you get on or if you need further assistance ok

Jan 18, 2010 | 2000 Chevrolet Blazer

1 Answer

Where is the IAC on a 2000 Chevy Blazer


On the intake manifold ( top of engine ) near air throttle body ( like where a carburator would be ) pressed against throttle linkage. Hope this helps.

May 04, 2009 | 2000 Chevrolet Blazer

Not finding what you are looking for?
2000 Chevrolet Blazer Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...