Question about 1999 Chevrolet Blazer

1 Answer

The driver's side power window is skipping or

The driver's side power window is skipping. It did this before and then finally wouldn't go up. I replaced the window motor and master control switch. It has worked fine for 3 month and now is jumping or skipping again.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,600 Answers

Most likely the rail has come loose inside the track you can drill a hole and put a #20 nut and screw in it to hold it tight so it won't move the track is the most common thing to wear out on the window. once you repair it it should be fine check all four corners the most common break is in the lower right side looking at the door with it open. Also the track will come loose as well and that can cause you the same problem, with the cover off the door operate it so you can determine which area it is jumping from and then fix it. also lube the tracks with synthetic grease to keep it from being hard to roll up also lube the rollers in the bottom of the track.

Posted on Jul 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the power window relay located in a 2002 mercury villager?


Principles of Operation
The driver power window regulator motor is controlled directly by the master window/door lock/unlock switch (and its integrated "auto down" module). Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The driver power window regulator motor is a reversible motor that is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The passenger power window regulator motor is controlled directly by the passenger power window switch and can also be controlled by the master window/door lock/unlock switch. Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The passenger power window regulator motor is a reversible motor, which is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The power rear quarter glass is also directly controlled by the master window/door lock/unlock switch. The power rear quarter glass power latches also utilize reversible motors. The power rear quarter glass power latches are operated by applying power and ground to the motor leads to open the window, and then reversing polarity on those same leads to close the window.
Visual Inspection Chart Mechanical Electrical
  • Improperly aligned window
  • Damaged window mounting
  • Window frame interference
  • Central junction box (CJB) Fuses:
    • F30 (10A)
    • F32 (20A)
    • F34 (20A)
    • F59 (7.5A)
  • Battery junction box (BJB) Fuses:
    • F20 (30A)
    • F27 (45A)
  • Switches
  • Circuits
  • Connectors
  • Heated back light
  • Relays
Which window is not working ?
  • Single power window is inoperative
  • Front door power window switch.
  • Front door power window regulator.
  • Circuit.
  • Driver door power window switch.
  • GO to Pinpoint Test B .

Apr 07, 2015 | 2002 Mercury Villager

1 Answer

Which Relay/Fuse controls the power windows?


Did you check for battery voltage at the switch , with a volt meter before you replaced the main driver door switch ? Maybe you'll want to take this to pro ,instead of just replacing parts !
Symptom Chart Condition Possible Sources Action
  • No communication with the smart junction box (SJB)
  • Circuitry
  • SJB
  • REFER to Section 419-10 .
  • A single power window is inoperative - driver front power window is inoperative/does not operate correctly
  • Power window motor regulator and motor
  • Circuitry
  • Window control switch
  • Smart junction box (SJB)
  • Go To Pinpoint Test A .
  • A single power window is inoperative - passenger front, left rear or right rear
  • Power window motor regulator and motor
  • Circuitry
  • Window control switch
  • Go To Pinpoint Test B .
  • All power windows are inoperative
  • Smart junction box (SJB) fuse 30 (10A)
  • SJB circuit breaker 10 (30A)
  • Circuitry
  • Delayed accessory relay
  • Battery saver relay
  • Driver window control switch
  • SJB
  • Go To
PINPOINT TEST C: ALL POWER WINDOWS ARE INOPERATIVE Test Step Result / Action to Take C1 CHECK FOR CORRECT OPERATION OF THE INTERIOR LIGHTS
  • Turn on the interior lights.
  • Do the interior lights operate normally?
Yes
GO to C2 .

No
To continue diagnosis, REFER to Section 417-02 . C2 CHECK CIRCUIT 400 (LB/BK) FOR VOLTAGE TO THE DRIVER WINDOW CONTROL SWITCH
  • Disconnect: Driver Window Control Switch C504b.
  • Key in ON position.
  • Measure the voltage between the driver window control switch C504b pin 4, circuit 400 (LB/BK), harness side and ground.
    >
  • Is the voltage greater than 10 volts?
Yes
GO to C4 .

No
GO to C3 . C3 CHECK CIRCUIT 400 (LB/BK) FOR AN OPEN OR SHORT TO GROUND
  • Key in OFF position.
  • Disconnect: SJB C2280c.
  • Measure the resistance between the driver window control switch C504b pin 4, circuit 400 (LB/BK), harness side and the SJB C2280c pin 17, circuit 400 (LB/BK), harness side; and between the driver window control switch C504b pin 4, circuit 400 (LB/BK), harness side and ground.
    >
  • Is the resistance less than 5 ohms between the driver window control switch and the SJB; and greater than 10,000 ohms between the driver window control switch and ground?
Yes
Go To Pinpoint Test H

No
REPAIR the circuit. TEST the system for normal operation.

Mar 24, 2015 | 2004 Mercury Sable

1 Answer

Grounding problem with my power window motor on a 1997 chevy camero


Test the MASTER switch at the drivers side. It seems to be a "wiring problem with the Master switch. The master switch is the switch that controls ALL the cars windows.

The passenger window switch gets both power and ground from the master switch. You have replaced the passenger side switch and it still had the same result and if the wiring is good from the master switch to the passenger side switch, then the only thing left would be the power window master switch. Check all wiring of the Master switch. That's the only thing that's left to do.

Mar 17, 2014 | Chevrolet Cars & Trucks

1 Answer

2002 thunderbird window won't go up or down replace swith still wont work fuse are ok does the switch get power


The master switch connector does have circuits that have power on them. The Master switch is not directly connected to the window motors. The switch sends a signal to the Front Electronic Module and the module controls operation of the motor on the driver side. The passenger door window motor is controlled by a different module

Nov 28, 2012 | 2002 Ford Thunderbird

1 Answer

Passanger side window wont roll up from that switch only on master switch


Window fuse's and relay's may be up under driver or passenger side dash or behind glove box, under the hood and even under the seats, and finally on the ends of the dash. All passenger power windows and locks are controlled thru and get power from the master control switch on the drivers door.

Drivers door window gets used the most so it could be the motor, window switch, relay or fuse.
Could also be a broken wire in the rubber boot going from the door to the body. You will have to eliminate each till you find the culprit. Check that all switches return to neutral when released.
The motor and the relay are the most likely to cause this problem. Try swapping the relay with a working window relay. If it still doesn't work, remove the door panel and remove the window motor.
Turn the motor shaft in both directions by hand several turns. Then plug the motor in and see if the switch will now run the motor. Sometimes that's all it takes to get it working again. I have had to do this with brand new motors. If voltage is not present at the motor connector, either a bad switch or a broken wire exists. Make sure to check for voltage coming to that windows switch. Actually, GM use's a circuit breaker type relay for each window and one fuse for all the circuit breakers.

Aug 25, 2011 | 2003 Cadillac CTS

1 Answer

All windows and sunroof will not budge suddenly. I replaed all fuses, and even tried a replacement master switch, but still not fixed. 1997 Landcruiser.


Window fuse's and relay's may be up under driver or passenger side dash or behind glove box, under the hood and even under the seats, and finally on the ends of the dash. All passenger power windows and locks are controlled thru and get power from the master control switch on the drivers door.

Drivers door window gets used the most so it could be the motor, window switch, relay or fuse.
Could also be a broken wire in the rubber boot going from the door to the body. You will have to eliminate each till you find the culprit. Check that all switches return to neutral when released.
The motor and the relay are the most likely to cause this problem. Try swapping the relay with a working window relay. If it still doesn't work, remove the door panel and remove the window motor.
Turn the motor shaft in both directions by hand several turns. Then plug the motor in and see if the switch will now run the motor. Sometimes that's all it takes to get it working again. I have had to do this with brand new motors. If voltage is not present at the motor connector, either a bad switch or a broken wire exists. Make sure to check for voltage coming to that windows switch.

Check the master window control panel on the driver's door. There is probably a lockout switch. It may have a window outline on one end and the same outline with an "X" over it on the other. Press the outline without the "X" and all your windows should work again. As silly as that sounds, a lot people hit that switch without knowing it. Also, if that switch(lockout) is faulty, none of the windows will work. That happens A LOT!!
You may also find that the connector has simply come loose from the master window control. Good luck!!

Aug 24, 2011 | Toyota Land Cruiser Cars & Trucks

1 Answer

Both power windows on the driver side do not roll down. I can't afford to repair yet. So if it's the motor, can I swap the motor from the passenger side rear to the driver side front?


Window fuse's and relay's may be up under driver or passenger side dash or behind glove box, under the hood and even under the seats, and finally on the ends of the dash. All passenger power windows are controlled thru and get power from the master control switch on the drivers door.

Drivers door window gets used the most so it could be the motor, window switch, relay or fuse.
Could also be a broken wire in the rubber boot going from the door to the body. You will have to eliminate each till you find the culprit. Check that all switches return to neutral when released.
The motor and the relay are the most likely to cause this problem. Try swapping the relay with a working window relay. If it still doesn't work, remove the door panel and remove the window motor.
Turn the motor shaft in both directions by hand several turns. Then plug the motor in and see if the switch will now run the motor. Sometimes that's all it takes to get it working again. I have had to do this with brand new motors. If voltage is not present at the motor connector, either a bad switch or a broken wire exists. Make sure to check for voltage coming to that windows switch. Actually, GM use's a circuit breaker type relay for each window and one fuse for all the circuit breakers.

Try this....
Open the door, turn the key to the ON position without starting the engine and everything that makes noise is off. Lean down placing your ears close to the bottom center of the door or at the speaker grill. Press the window switch UP and DOWN. Listen for the window motor. If heard the drive is damaged. If not heard, turn key off and locate and replace the relay with one of the other window relays. Check window again. If it works now, get a new relay. More often than not, removing the motor and turning it by hand will get it working good as new. I have had to do that with Brand New motors! So try it.
If all has failed, with the door panel still off, check for voltage at the motor connector when pushing the window switch. No voltage means its the switch, especially if its a auto down or up switch.

You may also find that the connector has simply come loose from the master window control. Good luck!!

Aug 19, 2011 | 1996 Oldsmobile Aurora

1 Answer

Wher is the power window relay for 1996 s-10 truck


Your problem is likely in the master switch on the driver side. Try getting a drivers door switch from the junkyard. I have a 96 Silhouette that I experienced the same problem with. After changing out the motor, and the passenger switch I finally traced it to the master switch. Power goes to the drivers door switch first and then over to the passenger door. It could actually be both switches. A bad relay would affect both windows not just the one side.

Jun 05, 2010 | 1996 Chevrolet S-10 Pickup

4 Answers

Problems with door locks and window


page 3-39 in owners manual. automatic door locks. do the steps and change too lock 2. this worked on my 2006 colorado crew cab. good luck

Apr 05, 2009 | 2005 Chevrolet Colorado

1 Answer

Rear side windows


This may be just a case of inadvertently hitting the window lock out n th driver door window switch by mistake. Check that first. Here's some background on window operation

Principles of Operation
The driver power window regulator motor is controlled directly by the master window/door lock/unlock switch (and its integrated "auto down" module). Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The driver power window regulator motor is a reversible motor that is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The passenger power window regulator motor is controlled directly by the passenger power window switch and can also be controlled by the master window/door lock/unlock switch. Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The passenger power window regulator motor is a reversible motor, which is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The power rear quarter glass is also directly controlled by the master window/door lock/unlock switch. The power rear quarter glass power latches also utilize reversible motors. The power rear quarter glass power latches are operated by applying power and ground to the motor leads to open the window, and then reversing polarity on those same leads to close the window.
Symptom Chart Condition Possible Sources Action
  • All windows are inoperative
  • BJB Fuse:
    • F20.
  • Circuit.
  • Power window relay.
  • Front door power window switch.
  • GO to Pinpoint Test A .
  • Single power window is inoperative
  • Front door power window switch.
  • Front door power window regulator.
  • Circuit.
  • Driver door power window switch.
  • GO to Pinpoint Test B .
  • Vent power window is inoperative — quarter window glass power latch
  • Circuit.
  • Quarter window glass switch.
  • Quarter window glass power latch.
  • GO to Pinpoint Test C .
  • The one touch down feature is inoperative
  • Master window regulator and door lock switch.
  • INSTALL a new master window/door lock/unlock switch. REFER to Switch—Master Window Door Lock/Unlock .
  • The back window will not defrost
  • CJB Fuses:
    • F30 (10A).
    • F32 (20A).
    • F34 (20A).
  • BJB Fuse:
    • F27 (45A)
  • Circuit.
  • Heated back window switch.
  • SEC/timer module.
  • Rear window defrost relay.
  • GO to Pinpoint Test D .
  • The back window defrost will not shut off automatically
  • SEC/timer module.
  • Circuit.
  • Rear window defrost relay.
  • GO to Pinpoint Test E .

Jan 28, 2009 | 1999 Mercury Villager

Not finding what you are looking for?
1999 Chevrolet Blazer Logo

247 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...