Question about 2004 Toyota ECHO

1 Answer

How do I remove the rear seat of Echo, 2004, sedan? Cat **** soaked foam.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 53 Answers

PULL REALLY HARD ON THE BOTTOM OF THE SEAT, WHERE IF U WERE SITTING DOWN YOUR BOTTOM OF YOUR CALF WOULD BE, THERE IS A CLIP THERE AND ONE ON THE OTHER SIDE. GOOD LUCK

Posted on Jul 17, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Toyota yaris Mk 1 radio no sound


I had this problem on a 2004 Echo sedan.
Check the rear speaker leads. One had broken off on mine and was grounding against the speaker frame, causing the amp to shut down. If this is the case, solder the lead back on and insulate it with black tape to keep it away from any metal parts. When the fault is cleared the radio should play again.

Feb 06, 2013 | 2004 Toyota Yaris 1.4

1 Answer

Where is fuel pump


pump located on top of the fuel tank just behind rear seat on driver side, to access pump, remove foam with three push-to-lock screws holding the foam running along the back of the seat, be careful not to break the foam, then 4 philip screws to remove floor panel to view the top of the fuel tank, there are about 8x 8mm hex nuts holding the complete intank fuel pump and fuel gauge.

Mar 22, 2011 | 2000 Subaru Forester

1 Answer

How do you remove the rear speakers from a 2004 chevy impala?


Remove the rear seat. On later models remove the rear upper quarter panel by pulling down & out to disengage the retainer clips, then sliding the roof leg out from under the trim panel over the door. Detach the rear seat belts through the slot in the rear parcel shelf. Pry up the plastic clips securing the rear parcel shelf. Then lift up & out to remove it from the vehicle. Remove the speaker retaining screws or tabs. If the speaker seal has bonded with the metal shelf, hold the tabs & pry the housing away from the metal. Disconnect the electical connector & remove the speaker. Install in reverse order. Good luck!

Feb 22, 2011 | 2007 Chevrolet Impala LS Sedan New Cars

1 Answer

Seat warmers on drivers side have gone out. How do you fix or replace?


depending on if it is the seat bottom or the seat back as they are seperate systems if both dont work then you probably have a electrical problem with the module or the switch not the heaters them selves, if it is one of the heaters then you must remove the seat cushion and replace it or the seat back cushion the heaters are intergrated into the foam the seat cushion unbolts with two fifteen millimeter nuts just under the front of the seat and unclips from the rear as you pull up and forward the seat back cushion is much more involved and should be done by a pro

Dec 18, 2010 | 2004 GMC Sierra

1 Answer

How do you remove the rear seat in a 2002 Mercedes C240?


please check below the rear seat you can see small plastic cover have fitted near seat it's same color of your interior carefully remove that plastic covers without braking locks then you can see bolt for remove rear seat cushion remove bolts and slide the cushion towards front.

Sep 14, 2010 | 2007 Mercedes-Benz C230 Sedan

1 Answer

I need to replace a rear seat belt in a 1997 Ford Tarsus. Does any know the best way to access the assembly? In addition, are there any diagrams available that show the connection points?


please don't forget to rate, thx.

Retractor and Tongue—Sedan
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Safety Belt Bolt Bit T77L-2100A
NOTE: Safety Belt Bolt Bit T77L-2100-A should be used for safety belt removal and installation.

Removal
  1. Remove rear seat cushion. Refer to Section 01-10 .
Seat Cushion, Rear Sedan
Removal
  1. Apply knee pressure to lower front portion of the rear seat cushion. Push rearward to disengage rear seat cushion pad and frame (600A88) from rear seat cushion front retainers (63370).
  1. Remove rear seat cushion from vehicle.
  1. Remove rear seat back. Refer to Section 01-10 .
Seat Back, Rear 60/40 Split Bench—Sedan
Removal
  1. NOTE: Safety belt bolts do not secure seat back to vehicle.

    Remove rear seat cushion as described.
  1. Fold down back seat and remove two bolts in the center of each seat back striker plates.
  1. Remove two bolts from outboard rear seat back frame retaining brackets.
  1. Lift seat back up and pull forward to remove from vehicle.
  1. Remove panel (52018) and quarter trim panel (31012). Refer to Section 01-05 .
Trim Panel, Quarter—Sedan Removal
  1. Remove rear seat. Refer to Section 01-10 .
  1. Pull up on rear section of rear door scuff plate that overlaps lower quarter trim panel.
  1. Pull lower quarter trim panel away from body.
  1. Remove safety belt retaining bolt.
  1. Feed safety belt through lower quarter trim panel.
  1. Remove safety belt anchor plate-to-sill bolt from quarter panel.
  1. Remove retractor anchor nut and retractor from rear quarter panel.
  1. Remove upper seat belt anchor bolt and anchor from upper rear quarter panel.
  1. Slide anchor plate end of safety belt through the openings in the quarter trim panel.
  1. Remove outboard front safety belt retractor and tongue (611B08) from the vehicle.


    2a6fac0.gif


    Item Part Number Description 1 386277-S190 Bolt (Part of 611B68) 2 31012 Upper Rear Quarter Trim Panel 3 611B60 Retractor and Tongue 4 N800937-S190 Nut 5 389370-S190 Bolt 6 — Rear Quarter Panel (Part of Body) 7 52018 Lower Rear Quarter Trim Panel 8 — Mounting Stud (Part of Body)
  1. Remove seat belt anchor bolt and retractor and tongue from rear deck panel.


    fff90b0.gif

Installation
  1. To install, reverse Removal procedure.
  1. Make sure the safety belt webbing is not twisted. If it is, remove the twist.
  1. Tighten retractor anchor bolt and safety belt anchor plate-to-sill bolt to 34-46 Nm (25-33 lb-ft).
  1. Check the restraint system for proper operation.

Jun 30, 2009 | 1997 Ford Taurus

1 Answer

Mustang rear seat removal?


please rate highly if this is what you need

Section 01-10: Seats and Tracks 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Seat Cushion, Rear Removal and Installation
  1. Release pin from locks by pressing release button under rear seat cushion.
  1. Pull rear safety belt and buckle (60044) through openings in rear seat cushion pad and frame (600A88) and remove rear seat cushion pad and frame .
  1. To install, reverse Removal procedure.
----------------------------------------------
Section 01-10: Seats and Tracks 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Seat Back, Rear Sedan
Removal
  1. Remove rear seat cushion as outlined.
  1. Remove rear seat bolster. Refer to Section 01-05 .

  1. Remove rear seat bolster mounting bolts. Remove bolster assembly.
  2. Remove four seat back to package tray retaining bolts.
  1. Remove seat back.
  1. To install, reverse Removal procedure.

May 04, 2009 | 2004 Ford Mustang

1 Answer

GS350 rear seat removal


You can remove your rear seat cushions if you place your hand under the seat cushion you should be able to feel a hook. lift the seat up a little bit and you should be able to release the hook.

Mar 15, 2009 | 2007 Lexus GS 350 AWD Sedan

1 Answer

How do I change the bulb 2004 infiniti high mount bake light?


Unfortunately, these are not very simple. If you have a factory high mount brake light-meaning not one in a spoiler, you have to remove the rear seats, the rear parcel shelf and then the 3rd brake light. the 3rd brake light I believe is an LED setup which get replaced as an assembly which inserts into the housing. If you need further guidance let me know.

Thanks,

Brian

Dec 10, 2008 | 2005 Infiniti G35

2 Answers

1998 honda civic ex sedan


remove rear seat, remove round metal cover, disconnect fuel lines and wires from top of fuel pump, jack up rear of car. remove gas tank straps, lower gas tank with a jack, install is reverse.....if you need to just replace the fuel pump you don't have to remove tank you Can access from under rear seat good luck and please rate -jeff

Jun 11, 2008 | 1998 Honda Civic

Not finding what you are looking for?
2004 Toyota ECHO Logo

Related Topics:

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...