Question about 1995 Honda Accord

1 Answer

I need to know where the thermostat housing is so i can replace...

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 396 Answers

It is hard to say definitely without a make, model and year of car. But I would follow the large radiator hose to the engine block. If the hose connects to a cast iron elbow with two bolts holding it to the block smile you most likely found it. Drain the radiator fluid, unbolt the two bolts and you should see the thermostat. Clean the old gasket of the block and elbow and bolt the elbow and new thermostat and gasket to the block to the manufactures torque specs. I would buy some radiator flush if it has not been flushes for several years. Fill the radiator with the correct ratio of coolant and water replace the cap then run the engine for 15 minutes and look for leaks or listen for hissing from the leaks.

Posted on Jul 17, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 Dodge 2.7 thermostat housing replacement


Hi Will, Look at the engine and follow the top radiator hose to the place where it enters the engine. Where it connects is the thermostat housing. The domed part is what you are looking for, but if you don't know what it is and what it looks like how do you know it needs replacement? Regards John

Jul 21, 2012 | Cars & Trucks

1 Answer

Engine Diagram 2007 kia sportage


With conventional cooling system, the upper radiator hose goes to thermostat housing on the engine. You drain antifreeze down, a little, remove radiator hose from thermostat housing, remove thermostat housing, the thermostat should be inside the housing.
Some antifreeze is poisonous, dispose of properly.
Install new thermostat, hook everything back up. Add proper amount of antifreeze to the proper mark. Keep an eye on antifreeze level for a while till your sure all air worked out of the system.

Nov 04, 2011 | 2007 Kia Sportage 4x4 V6

2 Answers

Check engine light is on . need to know where the thermostat is located


The thermostat is a black plastic water outlet housing connected to radiator hose. when replacing the thermostat the whole housing is replaced.

Nov 28, 2010 | 2006 Ford Fusion

1 Answer

Need to find where the thermastat is on a 2003 cadi


It is in the rear of the engine by the firewall and the intake manifold will need to be removed to gain access t it.

Engine Coolant Thermostat Replacement (LA3, LY9) Removal Procedure
  1. Remove the thermostat housing. Refer to Engine Coolant Thermostat Housing Replacement .

  2. 790876.gif
    tif.gif
  3. Complete the following in order to remove the thermostat from the thermostat housing:
  4. 2.1. Depress the ears on both sides of the thermostat. 2.2. Rotate the thermostat until it clears the retaining feature of the housing. 2.3. Release the pressure from the thermostat. 2.4. Pull the thermostat from the thermostat housing.
Installation Procedure

    790876.gif
    tif.gif
  1. Complete the following in order to Install the thermostat into the thermostat housing:
  2. 1.1. Align the thermostat pin to the thermostat housing orifice. 1.2. Depress the ears on both sides of the thermostat. 1.3. Rotate the thermostat until it aligns with the retaining feature of the housing. 1.4. Release the pressure from the thermostat.
  3. Install the thermostat housing. Refer to Engine Coolant Thermostat Housing Replacement .

Jul 10, 2010 | 2003 Cadillac CTS

1 Answer

2000 V6 Toyota Solara thermostat replacement


Just replaced one. It is on the driver's side of the engine. Follow the lower hose up. It is clamped to the inlet tube which is held in the thermostat housing by an O-Ring. There are three nuts holding the housing to the engine block. I managed to get mine off without the recommended removal of the aircleaner

Jul 02, 2010 | 2000 Toyota Camry Solara

1 Answer

I think i have located the thermostat but there is something mounted about it that would have to be unbolted in order to get to the thermostat, does anyone know what this is and if i can get to the...


You state that you think you have located the thermostat. The part that will need to be unbolted and removed is the thermostat housing. Simply remove the radiator hose and remove the bolts holding the housing in place. You may need to tap the housing gently to break it loose. The thermostat is located in the housing. Be sure to carefully scrap off any remaining gasket on the thermostat housing and the engine where the housing sits. Replace the thermostat and install a new gasket, replace housing, tighten bolts evenly and reattach radiator hose. Top off the radiator to replace any lost coolant.

Jun 28, 2010 | 1998 Mercury Sable

1 Answer

Need to know to replace themostat in 2004


Drain the radiator, follow the top radiator hose to the engine, it is connected to the thermostat housing. Loosen and remove the two bolts, lift the housing and remove thermostat, make sure the new thermostat goes back in the exact same way, tighten bolts, make sure pepcock is closed on radiator, refill radiator, start engine, run heater on full blast, add coolant as needed.

Dec 22, 2009 | Chevrolet TrailBlazer Cars & Trucks

1 Answer

Need to know if replacing a thermostat housing on a 2000 vw jetta is a 'do it yourself' kinda job? do you have a diagram?


You should have no problems replacing a thermostat housing or replacing a thermostat. get the correct thermostat and gasket if required and you'll have no problem.

Oct 27, 2009 | 2001 Volkswagen Jetta TDI

2 Answers

Need to replace thermostat housing in a 2000 pontiac grand am 2.4L. I know where it is but I need to know about any precautions and what is involved in the process,


Engine should be cool

Catch leaking anti-freeze from thermostat housing hose when disconnected (if any)

Good idea to always disconnect negative battery cable anytime working under hood for extended period

Clean old gasket of block

These come to mind.

Charlie

Oct 01, 2009 | 2000 Pontiac Grand Am GT

Not finding what you are looking for?
1995 Honda Accord Logo

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...