Question about Honda Accord

2 Answers

Cannot find explicit instructions on how to remove the cv joint from the steering knuckle so I can get to the four bolts that attach the hub unit to the steering knuckle. I am replacing the front rotors on a 91 Honda Accord.

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 115 Answers

Remove cv nut.. then ull need an air hammer to push the shaft through the hub... then remove brake caliper, 1 or 2 strut to knuckle bolts, tie rod, lower ball joint.. knuckle and rotor should come out in one piece... gonna need a floor press to push hub away from bearing then the rotors come off...

Posted on Jul 16, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 51 Answers

Can you send me some pictures? jtarin@cox.net

Posted on Jul 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace cv joints


Hi Douglas, I'm glad to help. My first suggestion is to get to complete shaft. This way you want have any problems later on. It's not that much more expensive and you'll be glad you did. Below is the procedure for replacing them.



FRONT DRIVESHAFTS

REMOVAL
  1. Raise vehicle on jack stands or centered on a frame contact type hoist. Refer to Hoisting in the Lubrication And Maintenance section of this manual for the required lifting procedure to be used for this vehicle.
  2. Remove the cotter pin and nut lock Hub And Bearing To Stub Axle Retaining Nut from the end of the stub axle.
  3. Remove the wheel and tire assembly from the vehicle.
  4. Remove the wave washer Wave Washer from the end of the stub axle CAUTION: Wheel bearing damage will result if after loosening hub nut, vehicle is rolled on the ground or the weight of the vehicle is allowed to be supported by the tires.
  5. With the vehicle's brakes applied to keep hub from turning, loosen and remove the stub axle to hub nut.
  6. Remove the two front disc brake caliper to steering knuckle attaching bolts Front Disc Brake Caliper Attaching Bolts
  7. Remove the disc brake caliper from the steering knuckle. Caliper is removed by first rotating top of caliper away from steering knuckle and then removing bottom of caliper out from under machined abutment on steering knuckle Brake Caliper Mounting To Steering Knuckle
  8. Support disc brake caliper assembly by using a wire hook and suspending it from the strut assembly Correctly Supported Disc Brake Caliper Do not allow the brake caliper assembly to hang by the brake flex hose.
  9. Remove the brake rotor from the hub and bearing assembly Remove/Install Brake Rotor
  10. Remove nut attaching outer tie rod end to steering knuckle Removing Tie Rod End Attaching Nut Nut is to be removed from tie rod end using the following procedure, hold tie rod end stud with a 11/32 socket while loosening and removing nut with a wrench.
  11. Remove tie rod end from steering knuckle using Remover, Special Tool MB-991113 Tie Rod End Removal From Steering Knuckle Arm
  12. Remove the steering knuckle to ball joint stud, clamping nut and bolt Control Arm To Steering Knuckle Attachment from the steering knuckle.
  13. Using a pry bar, separate steering knuckle from ball joint stud Separating Ball Joint Stud From Steering Knuckle Note: Use caution when separating ball joint stud from steering knuckle, so ball joint seal does not get cut. NOTE: Care must be taken not to separate the inner C/V joint during this operation. Do not allow driveshaft to hang by inner C/V joint after removing outer C/V Joint from the hub/bearing assembly in steering knuckle, end of driveshaft must be supported.
  14. Pull steering knuckle assembly out and away from the outer C/V joint of the driveshaft assembly Steering Knuckle Separation From Driveshaft
  15. Support the outer end of the driveshaft assembly. Insert a pry bar between inner tripod joint and transaxle case Disengaging Inner Tripod Joint From Transaxle Pry against inner tripod joint, until tripod joint retaining snap ring is disengaged from transaxle side gear.
  16. Hold inner tripod joint and interconnecting shaft of driveshaft assembly. Remove inner tripod joint from transaxle, by pulling it straight out of transaxle side gear and transaxle oil seal Tripod Joint Removal from Transaxle When removing tripod joint, do not let spline or snap ring drag across sealing lip of the transaxle to tripod joint oil seal.
INSTALLATION
  1. Thoroughly clean spline and oil seal sealing surface, on tripod joint. Lightly lubricate oil seal sealing surface on tripod joint with fresh clean transmission lubricant.
  2. Holding driveshaft assembly by tripod joint and interconnecting shaft, install tripod joint into transaxle side gear as far as possible by hand Tripod Joint Removal from Transaxle
  3. Grasp inner tripod joint an interconnecting shaft. Forcefully push the tripod joint into side gear of transaxle, until snap ring is engaged with transaxle side gear. Test that snap ring is fully engaged with side gear by attempting to remove tripod joint from transaxle by hand. If snap ring is fully engaged with side gear, tripod joint will not be removable by hand.
  4. Clean all debris and moisture out of steering knuckle, in the area were outer C/V joint will be installed into steering knuckle.
  5. Ensure that front of outer C/V joint which fits against the face of the hub and bearing is free of debris and moisture before installing outer C/V joint into hub and bearing assembly Outer C/V Joint Inspection
  6. Slide drive shaft back into front hub and bearing assembly. Then install steering knuckle onto the stud of the ball joint assembly Steering Knuckle Separation From Driveshaft
  7. Install a new steering knuckle to ball joint clamping bolt and nut Control Arm To Steering Knuckle Attachment Tighten the clamping bolt and nut to a torque of 135 N·m (100 ft. lbs.)
  8. Install tie rod end into steering knuckle. Start attaching nut onto stud of tie rod end. While holding stud of tie rod end stationary using a 11/32 socket, Removing Tie Rod End Attaching Nut tighten tie rod end to steering knuckle attaching nut. Then using a crowfoot and 11/32 socket Torquing Tie Rod End Attaching Nut , tighten the tie rod end attaching nut to a torque of 54 N·m (40 ft. lbs.)
  9. Install braking disc on hub and bearing assembly Remove/Install Brake Rotor
  10. Install disc brake caliper assembly on steering knuckle. Caliper is installed by first sliding bottom of caliper under abutment on steering knuckle, and then rotating top of caliper against top abutment Brake Caliper Mounting To Steering Knuckle
  11. Install disc brake caliper assembly to steering knuckle attaching bolts Front Disc Brake Caliper Attaching Bolts Tighten the disc brake caliper assembly attaching bolts to a torque of 22 N·m (195 in. lbs.)
  12. Clean all foreign matter from the threads of the outer C/V joint stub axle. Install the washer and stub axle to hub/bearing assembly nut on stub axle and securely tighten nut.
  13. Install front wheel and tire assembly. Install and tighten the wheel mounting stud nuts in proper sequence until all nuts are torqued to half the required specification. Then repeat the tightening sequence to the full specified torque of 135 N·m (100 ft. lbs.)
  14. Lower vehicle.
  15. With the vehicle's brakes applied to keep hub from turning, tighten the hub nut to a torque of 244 N·m (180 ft. lbs.) Torquing Front Stub Axle To Hub Nut
  16. Install the spring wave washer on the end of the stub axle.
  17. Install the hub nut lock, and a new cotter pin Hub And Bearing To Stub Axle Retaining Nut Wrap cotter pin prongs tightly around the hub nut lock as shown in Hub And Bearing To Stub Axle Retaining Nut
  18. Check for correct fluid level in transaxle assembly. Refer to Group 21, Transaxle for the correct fluid level checking procedure for the type of transaxle being checked.
  19. Set front toe on vehicle to required specification.

May 07, 2014 | 2000 Dodge Caravan

1 Answer

Tring to remove cv joint on 2001 intrepid but transaxel shaft seems stuck to cv joint cant dislodge.....does it have a lock or something.......whats the best way to remove


use a large pry bar pry the inner tripod cv joint out of the transaxle differential gears.you have a retaining circlip that holds transaxle in place in the transaxle.besure to replace circlip and o ring seal on the transaxle stub shaft.torque strut assembly to steering knuckle attaching bolts.install the nuts to the attaching bolts and while holding bolt heads torque to 125 ft lbs and torque axle hub nut 125 ft lbs

May 18, 2011 | 2001 Dodge Intrepid

1 Answer

How do i remove the left cv axle shaft on my 1999 ford escort zx2?


take wheel off take big nut off cv shaft so it can slide out of hub assembly, take bolt out that holds strut to hub assembly an bolt lower ball joint and tie rod end take hammer and tap knuckle where steering end attaches, pry out ball joint and take axle end out of hub assembly. then carefully with pry bar pop it out of tranny. when install cv axle push in tranny fast so that you feel it snap in. good luck

Jan 20, 2011 | 1999 Ford Escort

1 Answer

How to remove front axle on a 2002 dodge intrepid


raise you vehicle on jackstands. remove front wheel and tire.remove front caliper from steering knuckle assembly, remove rotor from hub by pulling it staright off. remove speed sensor bracket from strut assembly. remove hub and bearing to stub axle retaining nut. dislodge inner CV stub shaft retaining ringon transaxle assembly. insert small pry bar between transaxle case and inner CV joint by prying on it.remove strut assembly to steering knuckle bolts remove top of steering knuckle from strut assembly, then rotate CV assembly out of vehicle. Remove inner shaft from transaxle stub shaft grasp inner CV joint and interconnecting shaft and pull both pieces out at the same time. good luck!

Oct 30, 2010 | Dodge Intrepid Cars & Trucks

2 Answers

On my 97 the abs ring on the cv axle is almost gone!! made a turn today and the wheel almost locked up..any help??


I would have the cv axle changed along with any integral parts such as the abs ring.

REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Remove the wheel cover/hub cover from the wheel and tire assembly, then loosen the lug nuts. Fig. 1: After removing the wheel/hub cover, loosen the lug nuts 86877115.gif

  3. Raise and safely support the vehicle, then remove the wheel and tire assembly. Insert a steel rod in the rotor to prevent it from turning, then remove the hub nut and washer. Discard the old hub nut. Fig. 2: Before removing the hub nut and washer, insert a steel rod in the rotor to prevent it from turning 86877116.gif
    Fig. 3: Remove the hub nut and washer, then discard the nut, and replace with a new one during installation 86877117.gif

  4. Remove the nut from the ball joint to steering knuckle attaching bolts.
  5. Drive the bolt out of the steering knuckle using a punch and hammer. Discard this bolt and nut after removal. Fig. 4: Drive the bolt out of the front wheel knuckle using a punch and hammer, then discard the nut and bolt and replace with new ones during installation 86877118.gif

  6. If equipped with anti-lock brakes, remove the anti-lock brake sensor and position it aside. If equipped with air suspension, remove the height sensor bracket retaining bolt and wire sensor bracket to inner fender. Position the sensor link aside. Fig. 5: If so equipped, remove the anti-lock brake sensor and position it aside 86877119.gif

  7. Separate the ball joint from the steering knuckle using a suitable prybar. Position the end of the prybar outside of the bushing pocket to avoid damage to the bushing. Use care to prevent damage to the ball joint boot. Remove the stabilizer bar link at the stabilizer bar. Fig. 6: When separating the ball joint from the steering knuckle, be careful not to damage to ball joint boot 86877120.gif
    1. Slide the link shaft out of the transaxle. Support the end of the shaft by suspending it from a convenient underbody component with a piece of wire. Do not allow the shaft to hang unsupported, damage to the outboard CV-joint may occur.
    2. Separate the outboard CV-joint from the hub using front hub remover tool T81P-1104-C or equivalent and metric adapter tools T83P-1104-BH, T86P-1104-Al and T81P-1104-A or equivalent. NOTE: Never use a hammer to separate the outboard CV-joint stub shaft from the hub. Damage to the CV-joint threads and internal components may result. The halfshaft assembly is removed as a complete unit.
    3. Install the CV-joint puller tool T86P-3514-A1 or equivalent, between CV-joint and transaxle case. Turn the steering hub and/or wire strut assembly aside.
    4. Screw extension tool T86P-3514-A2 or equivalent, into the CV-joint puller and hand tighten. Screw an impact slide hammer onto the extension and remove the CV-joint.
    5. Support the end of the shaft by suspending it from a convenient underbody component with a piece of wire. Do not allow the shaft to hang unsupported, damage to the outboard CV-joint may occur.
    6. Separate the outboard CV-joint from the hub using front hub remover tool T81P-1104-C or equivalent and metric adapter tools T83P-1104-BH, T86P-1104-Al and T81P-1104-A or equivalent.
    7. Remove the halfshaft assembly from the vehicle. Fig. 7: These tools are necessary for halfshaft removal 86877121.gif
      Fig. 8: Installing the specified tools to remove the halfshaft assembly from the vehicle 86877122.gif
      Fig. 9: Support the end of the shaft by suspending it from a convenient underbody component with a piece of wire. Do not allow the shaft to hang unsupported, since damage to the outboard CV-joint may occur 86877123.gif
      Fig. 10: Separate the outboard CV-joint from the hub using front hub remover tool T81P-1104-C or equivalent, and metric adapter tools T83P-1104-BH, T86P-1104-Al and T81P-1104-A or equivalent, then remove the halfshaft assembly from the vehicle 86877124.gif
      Fig. 11: Exploded view of the halfshaft assemblies and related components - automatic transaxle 86877125.gif
prev.gif next.gif

Oct 26, 2010 | 1997 Lincoln Continental

2 Answers

Im trying to replace the rotors and im having a Hard time getting it off. HELP


You might want to spray some WD-40 around the center of the rotor and the wheel lugs. Usually on Honda's, the rotors will have 2 threaded holes to put in bolts. Screw in each bolt equally to help push the rotor away from the hub.

May 12, 2010 | 1995 Honda Accord

1 Answer

Steering knuckle removal


Are you talking about your CV shaft? To remove the knuckle, undo the CV shaft nut, remove the tie rod end nut, the upper and lower ball joints, and the steering knuckle will come off, then you can get to the wheel bearing hub bolts.

Jul 25, 2009 | 1991 Honda Accord

1 Answer

Bad right rear axle. Need to know how to replace axle.


Dana or Ford axle?

Ford here:
SECTION 205-05: Rear Drive Halfshafts 2002 Explorer/Mountaineer Workshop Manual
REMOVAL AND INSTALLATION Halfshaft
Special Tool(s) s2n~us~en~file=st2258a.gif~gen~ref.gif Protector, Differential Seal
205-506 s2n~us~en~file=st2272a.gif~gen~ref.gif Remover, Front Wheel Hub
205-D070 (D93P-1175-B) or equivalent s2n~us~en~file=st2309a.gif~gen~ref.gif Remover, Halfshaft
205-502
Removal and Installation
NOTE: This procedure applies to both rear halfshaft assemblies.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not loosen the rear axle wheel hub retainer until after the wheel and tire assembly are removed from the vehicle. Wheel bearing damage will occur if the wheel bearing is unloaded with the weight of the vehicle applied.
    With the vehicle in NEUTRAL, raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the rear wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. NOTE: Have an assistant press the brake pedal to keep the axle from rotating.
    Remove and discard the rear axle wheel hub retainer and the washer.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent damage to the brake hose, do not allow the disc brake caliper to hang suspended from the hose.
    Remove the brake disc.
    1. Remove the two bolts and lift the disc brake caliper and brake pads off the brake disc.
      • Using mechanics wire, position the disc brake caliper out of the way.
    1. Remove the brake disc.
  1. Remove the bolt retaining the parking brake cable bracket to the frame.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Cover the stabilizer link bolt threads and the nut to prevent boot damage when removing the halfshaft assembly from the vehicle.
    Using a rubber hose approximately 37.5 mm (1.5 in) long, cover the stabilizer link bolt threads and nut.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif WARNING: The bolt that retains the upper ball joint to the knuckle is longer and it has fewer threads than the bolt that retains the toe link to the knuckle. Switching these bolts during installation will prevent the pinch arms on the knuckle from correctly retaining the toe link to the knuckle. This may cause the toe link to separate from the knuckle during vehicle operation. Failure to follow these instructions may result in personal injury.
    Remove the pinch bolts and disconnect the toe link and upper ball joint from the knuckle.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Support the rear suspension upper arm to prevent boot damage when removing the halfshaft assembly from the vehicle.
    Using a wood stick, approximately 450 mm (18 in) long and 25 mm (1 in) wide, support the rear suspension upper arm.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not use a hammer to separate the outboard CV joint from the hub. Damage to the threads and internal CV joint components may result.
    s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Once the outboard CV joint separates from the hub the knuckle will continue to pivot until the brake backing plate presses against the suspension lower arm. To prevent damage to the brake backing plate, immediately after separating the outboard CV joint from the hub, rest the knuckle on a cushioned support that is tall enough to keep the backing plate from pressing against the suspension lower arm.
    Separate the outboard CV joint from the hub and rest the knuckle on a cushioned support.
    1. Using the special tool, press the outboard CV joint until it is loose in the hub.
    1. Remove the special tool.
    1. Separate the outboard CV joint from the hub.
    1. Rest the knuckle on a cushioned support.
04ab306.gif
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the axle shaft oil seal or the machined sealing surface on the inboard CV joint housing.
    s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not allow the splines on inboard CV joint housing to touch the axle shaft oil seal.
    NOTE: A circlip retains the inboard CV joint housing to the differential side gear in the axle.
    Using the special tool, disengage the inboard CV joint housing from the differential side gear.
c231bc2.gif
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent damage to the axle shaft oil seal, install the special tool before removing the inboard CV joint housing from the axle.
    Install the special tool.
50c5d1d.gif
  1. Remove the halfshaft assembly from the vehicle.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent damage to the axle shaft oil seal, install the Differential Seal Protector before positioning the inboard CV joint housing in the axle.
    s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Always install the halfshaft with a new retainer circlip and a new rear axle wheel hub retainer.
    s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Never use power tools to tighten the rear axle wheel hub retainer.
    To install, reverse the removal procedure.

Apr 17, 2009 | Ford Explorer Cars & Trucks

1 Answer

Replacing a front wheel bearing


here is a step by step instructions on how to replace your bearing. please copy and paste the link into your browser for an image.

please do not forget to rate and comment about your experience with fixya today.

Removal & Installation
  1. Apply the brakes and hold in place.
  2. Raise the vehicle.
  3. Remove the front tire and wheel assembly.
  4. Remove the cotter pin, lock nut and spring washer from the hub nut.
  5. While the brakes are applied, loosen and remove the hub nut on the end of the driveshaft.
  6. Release the brakes.
  7. Remove the front disc brake caliper and adapter as an assembly, and the brake rotor from the steering knuckle.
  8. Remove the nut attaching the outer tie rod to the steering knuckle. To do this, hold the tie rod end stud with a wrench while loosening and removing the nut with a standard wrench or crowfoot wrench.
  9. Remove the tie rod end from the steering knuckle using Remover, Special Tool MB991113.
  10. Remove the tie rod heat shield.
  11. Remove the nut and pinch bolt clamping the ball joint stud to the steering knuckle.

    CAUTION The strut assembly-to-steering knuckle attaching bolts are serrated and must not be turned during removal. Hold the bolts stationary in the steering knuckles while removing the nuts, then tap the bolts out using a pin punch.
  12. Remove the two bolts attaching the strut to the steering knuckle.

    NOTE Use caution when separating the ball joint stud from the steering knuckle, so the ball joint seal does not get cut.
  13. Separate the ball joint stud from the steering knuckle by prying down on lower control arm and up against the ball joint boss on the steering knuckle.

    NOTE Do not allow the driveshaft to hang by the inner C/V joint; it must be supported to keep the joint from separating during this operation.
  14. Pull the steering knuckle off the driveshaft outer C/V joint splines and remove the steering knuckle.

    NOTE The cartridge type front wheel bearing used on this vehicle is not transferable to the replacement steering knuckle. If the replacement steering knuckle does not come with a wheel bearing, a new bearing must be installed in the steering knuckle. Installation of the new wheel bearing and hub must be done before installing the steering knuckle on the vehicle.
  15. If the wheel bearing and hub need removal. Do not reuse the wheel bearing.
    http://www.chiltonlibrary.com/content/images/32050/images/32050_ptcr_g0035.gif The separation of the ball joint and the knuckle
To install:
  1. Slide the hub of the steering knuckle onto the splines on the driveshaft C/V joint.
  2. Install the steering knuckle onto the ball joint stud aligning the bolt hole in the knuckle boss with the notch formed in the side of the ball joint stud.
  3. Install a new ball joint stud pinch bolt and nut. Tighten the nut to a torque of 70 ft. lbs. (95 Nm).

    CAUTION The strut assembly-to-steering knuckle attaching bolts are serrated and must not be turned during installation. Install the nuts while holding the bolts stationary in the steering knuckle.
  4. Position the lower end of the strut assembly in line with the upper end of the steering knuckle and align the mounting holes . Install the two attaching bolts. The bolts should be installed with so that the nuts face towards the front of the vehicle once installed. Install the nuts. Holding the bolts in place tighten the nuts to a torque of 40 ft. lbs. (53 Nm) plus an additional 90° turn after the specified torque is met.
  5. Place the tie rod heat shield on the steering knuckle arm so that the shield is positioned straight away from the steering gear and tie rod end once installed. Align the hole in the shield with the hole in the steering knuckle arm. Install the outer tie rod ball stud into the hole in the steering knuckle arm. Start the tie rod attaching nut onto the stud. Hold the tie rod end stud with a wrench while tightening the nut with a standard wrench or crowfoot wrench. To fully tighten the nut to specifications, use a crowfoot wrench on a torque wrench to turn the nut, and a wrench on the stud.
  6. Tighten the nut to a torque of 40 ft. lbs. (55 Nm). Install the brake rotor, disc brake caliper and adapter.
  7. Clean all foreign matter from the threads of the driveshaft outer C/V joint. Install the hub nut in the end of the driveshaft and snug it.
  8. Have a helper apply the brakes. With vehicle brakes applied to keep brake rotor and hub from turning, tighten the hub nut to a torque of 180 ft. lbs. (244 Nm)
  9. Install the spring washer, lock nut and cotter pin on the hub nut. Wrap the cotter pin ends tightly around the lock nut.
  10. Install the tire and wheel assembly. Install the wheel mounting nuts and tighten them to a torque of 100 ft. lbs. (135 Nm).
  11. Lower the vehicle.
  12. Set the front toe on the vehicle to required specification.

Apr 17, 2009 | 2003 Chrysler PT Cruiser

1 Answer

How do i remove thefront rotors on my 05 chey colorado. i removed the hub bolts but the rotor still seemedto be tightly attached. do i need a special tool. i did ot want to try and force it. thaks for your...


As you probably are aware, those rotors are mounted inboard of the outer hub flange on your vehicle. Once you've removed the caliper bracket, you can remove the hub. The four bolts that fasten the hub to the steering knuckle most be removed. If you look behind the steering knuckle you'll see them. If your vehicle is four wheel drive, you must remove the front CV shaft nut as well. You will probably have to disconnect the lower ball joint to slide the shaft out of the hub far enough to get clearance for the bottom bolts. Once you remove the hub from the knuckle, you can remove the rotor from the hub assembly. Incidentally, the hub bolts have thread lock compound on them from the factory, that tends to make them really tough to remove however they will come out. Reinstallation is naturally the reverse of removal. I hope this helps.

Nov 19, 2008 | 2005 Chevrolet Colorado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...