Question about 2004 Nissan Altima

1 Answer

'04 Nissan Altima can't be trained to open garage door.

My '04 Nissan Altima says to push both side buttons erase the factory set code, and when the red button flashes and then hold the remote garage opener button down with the middle button down to make it open the garage door by itself, but it won't learn! I held the remote devise button and the middle button together but nothing works. What am I doing wrong?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 93 Answers

Hello , you are probably not doing anything wrong. Some garage door openers will not accept some codes. My Toyota Tundra 2005 worked on my garage door , but my 2004 F250 would not. Quinn , Arizona

Posted on Jul 25, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you connect the home link garage control to your car & garage?


Things You'll Need
  • Remote garage door opener
Suggest Edits
    • 1

      Turn your Chrysler vehicle off and press and hold the two outside buttons on your onboard opener system. Release the buttons once the red indicator light begins flashing. This will erase any previous codes programmed to your system.

    • 2

      Hold your garage door opener remote two inches away from the onboard system.

    • 3

      Press and hold the button you wish to program on your onboard system and the open button on your remote simultaneously. Release the buttons once the indicator light on the onboard system begins flashing.

    • 4

      Press the training button on your Chrysler's system until the light glows solid. If it does not glow solid, continue to the following steps.

    • 5

      Press the "learn" button on your garage door remote, located near the antenna wire on the back or side of the system, and return to your vehicle.

    • 6

      Press the training button on your on board system, hold it for two seconds and release. Repeat the press/hold/release step two more times and your remote will be programmed and ready for use.

Dec 10, 2011 | 2002 Chrysler Town & Country

1 Answer

How do you "train" the


Instructions
    • 1 Turn off the engine of the car and press and hold buttons 1 and 3 on the Jeep's transmitter for 20 seconds to erase previous codes. Release them when the display reads "Channels Cleared."
    • 2 Hold your garage-door remote 1 to 3 inches from the Jeep transmitter.
    • 3 Press and hold the open button on your handheld remote and simultaneously press the button you wish to program on the Jeep's transmitter. For example, if you want button 2 to be the one you use to open your garage door, press button 2 while pressing the open button the remote.
    • 4 Release the button once you hear a beep and the display reads "Trained."
    • 5 Press the "smart" button on your garage door motor. This button is usually located on the back or side of the motor near the antenna wire and light lens.
    • 6 Return to your vehicle and press and hold the programmed button in your Jeep for 2 seconds. Release and press and hold the button for another 2 seconds to complete the programming sequence. You will now be able to use the vehicle's transmitter to open your garage door.

Sep 14, 2011 | 2001 Jeep Grand Cherokee

2 Answers

How to program my cars garage door opener buttons for my garage door.


GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

PLEASE NOTE: NOT ALL BRANDS/MODELS OF OPENER WILL WORK WITH THIS SYSTEM.

HOPE THIS HELPS

May 15, 2010 | 2001 Nissan Altima

1 Answer

2005 honda odyssey homelink programming


If you just received your vehicle and have not trained any of the buttons in HomeLink before, you should erase any previously learned codes before training the first button. To do this, press and hold the two
outside buttons on the HomeLink Transceiver for about 20 seconds, or
until the red indicator flashes.
Release the buttons, then go to step 1.
If you are training the second or third buttons, go directly to step 1.

1. Unplug the garage door opener motor from the electrical outlet.
2. Hold the end of the garage door opener remote 2 to 5 inches from HomeLink. Make sure you are not blocking your view of the red indicator in HomeLink.
3. Press and hold the remote transmitter button and one of the HomeLink buttons at the same time.
If the red indicator in HomeLink begins to flash slowly at first, then rapidly, release both buttons, and go to step 5. If the red indictor in HomeLink continues to flash slowly (does not flash rapidly), your remote transmitter may stop transmitting after a short time. Go to step 4.
4. Press and hold the remote transmitter button and one of the HomeLink buttons at the same
time. While continuing to hold the HomeLink button, press and release the remote transmitter button every 2 seconds. If the red indicator in HomeLink begins to flash slowly at first, then rapidly, release both buttons, and go to step 5. If the red indicator in HomeLink continues to flash slowly (does not begin to flash rapidly), repeat steps 2 thru 4.
5. Plug in the garage door opener motor, then test the HomeLink button by pushing it for about 1
second. If the button works, programming is complete. If the button does not work go to step 6.
6. Push and hold the HomeLink button for a few seconds, then watch the red indicator on HomeLink.
If the indicator stays on or flashes slowly, repeat steps 2 thru 5. If the indicator flashes rapidly
for 2 seconds then stays on, you have a rolling code transmitter. Go “Training with a Rolling Code System”
7. two HomeLink buttons to operate any other compatible remotely controlled devices around your
home (lighting, automatic gate, security system, etc.).
Repeat these steps to train the other

Jan 05, 2010 | 2006 Honda Odyssey

1 Answer

Program 2004 mercury mountainer garage opener


Verify the hand-held transmitter is operative.
Prepare for programming the universal transmitter by erasing all three channels (hold down the two outside buttons until the red light begins to flash [20-30 seconds]). Release both buttons.
Select one of the three universal transmitter channels to be programmed by pressing the desired button
Hold the end of the hand-held transmitter 25-51 mm (1-2 in) from the front surface of the universal transmitter so that the red light can still be seen
Use both hands to press the hand-held transmitter button and the desired button on the universal transmitter. Do not release either button.
Hold down both buttons until the red light on the universal transmitter flashes, first slowly and then rapidly. Release both buttons when the rapid flashing begins. The universal transmitter has successfully learned the new frequency signal and can be used in place of the hand-held transmitter(s).
If the hand-held transmitter appears to program the universal transmitter but does not open the garage door, the garage door opener may have a code protected or rolling code feature.
To operate, simply press the appropriate button on the universal transmitter. The red light is on while the signal is being transmitted.
IF THE GARAGE OPENER HAS ROLLING CODES---
program as above then------
Train the garage door opener receiver to recognize the universal transmitter.
Remove the cover panel from the garage door opener receiver.
Locate the training button on the garage door opener receiver. Location and color of the button may vary by garage door opener manufacturer. Refer to the garage door opener instruction manual or owner literature.
Press the training button on the garage door opener receiver for 1-2 seconds.
Press the programmed universal transmitter button for as long as the universal transmitter red light flashes (1-2 seconds). Release the button and re-press the button to confirm that the universal transmitter is trained to the receiver.
The garage door opener should recognize the universal transmitter.

Apr 01, 2009 | 2004 Mercury Mountaineer

1 Answer

2007 Lincoln Town Car Limited-can't program garage door entry key


ok

Learn Mode
ani_caut.gif WARNING: A garage door opening system that cannot stop or reverse itself after detecting an object in its path does not meet current federal safety standards. To decrease the risk of serious injury or death, do not use the universal transmitter with a door opening system that lacks stop and reverse features as required by federal standards. This includes any garage door opening system manufactured before April 1, 1982.
ani_caut.gif CAUTION: During this procedure, the system that you are programming will be made to operate. Make sure that people or objects are clear of the garage door or gate being programmed.
  1. Select a universal transmitter button to train.
  1. NOTE: If more than one button is pressed, priority will be given to the lowest numbered channel.
    Press and continuously hold the button for 20 seconds. CHANNEL X TRANSMIT will be displayed (X will be 1, 2 or 3) during this time.
  1. NOTE: If the channel being trained has not been previously trained, the channel will immediately enter training mode (no 20 second delay).
    After 20 seconds, the display will read CHANNEL X TRAINING to indicate training has started.
  1. Point the original garage door opener transmitter at the overhead console. Hold down the original transmitter's transmit button so the overhead console can learn the original transmitter's frequency and data stream.
  1. Training will be completed in 100 seconds or less. CHANNEL X TRAINED will be displayed when training is complete. DID NOT TRAIN will be displayed if the channel did not correctly train.
  1. NOTE: Additional training may be required for rolling code equipped devices. For additional information, refer to Rolling Code Programming in this section.
    Release the channel X button. Training is complete.
Rolling Code Programming
NOTE: To train a garage door opener (or other rolling code-equipped devices) with the rolling code feature, follow these instructions after completing the learn mode.
  1. Locate the learn or smart button on the garage door motor head unit. Exact location and color of the button may vary by product brand. If there is difficulty locating the learn or smart button, refer to the device's Owner's Literature.
  1. Press and release the learn or smart button on the garage door motor head unit.
  1. NOTE: Following the previous step, there are 30 seconds in which to proceed.
    Press and release the programmed universal transmitter button. Press and release the universal transmitter button a second time to complete the training process. (some garage door openers may require this procedure to be done a third time to complete the training.)
Transmit Mode
  1. Select the button for the desired channel (for example, for the garage door you wish to open).
  1. NOTE: If more than one button is pressed, priority will be given to the lowest numbered channel.
    Press the button. CHANNEL X TRANSMIT is displayed.
  1. The correct signal is transmitted to the device being controlled.
  1. Release the button.
Erase Mode
  1. Simultaneously press and hold buttons 1 and 3 for 20 seconds.
  1. CLEARING CHANNELS will be displayed while the channel codes are being erased.
  1. CHANNELS CLEARED will be displayed when the erase operation is complete.
  1. Release buttons 1 and 3.
Universal Transmitter Default Code Mode Loading
  1. Press and hold buttons 1 and 3 simultaneously. CLEARING CHANNELS is displayed.
  1. After 20 seconds, CHANNELS CLEARED is displayed. Continue to hold buttons.
  1. After 10 more seconds, CHANNELS DEFAULTED is displayed when the default codes have been successfully loaded

Dec 30, 2008 | 2007 Lincoln Town Car Signature Limited...

2 Answers

Home link system program?


  1. Turn off the engine.
  2. Erase the factory test codes by pressing buttons 1 and 3. Release the buttons when the two green lights begin to flash (about 20 seconds ).
  3. Choose one of the three buttons to train. Position the end of your hand-held transmitter 1-3 inches (5-14 cm) away from the lower left corner of the EVIC display while keeping the display in view.
  4. Simultaneously press and hold both the desired Transmitter button and the hand-held transmitter button. After a short time, the message TRAINING will show on Transmitter display. Do not release the buttons until the message TRAINED appears on the display (this may take as long as 60 seconds ), release both the Transmitter and hand-held transmitter buttons.
  5. Press and hold the just-trained Transmitter button. TRANSMIT should appear on the display. If your device activates when the Transmitter button is depressed and released, programming is complete. To train the other buttons, repeat the process. Be sure to keep your hand-held transmitter in case you need to retrain the universal transmitter. NOTE: If the message TRANSMIT appears on the Transmitter display but your device does not activate, the device may be equipped with a "rolling code" system. Continue with steps six through eight below to complete the programming of a rolling code equipped device (most commonly a garage door opener).
  6. At the garage door opener receiver (motor-head unit) in the garage, locate the "learn" or "smart" button. This can usually be found where the hanging antenna wire is attached to the motor-head unit. Firmly press and release the "learn" or "smart" button. (The name and color of the button may vary by manufacturer.) NOTE: There are 30 seconds in which to initiate the next step.
  7. Return to the vehicle and firmly press, hold for two seconds and release the programmed Transmitter button. Repeat the "press/hold/release" sequence a second time, and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming process.
  8. Transmitter should now activate your rolling code equipped device. To program the remaining two buttons, simply repeat the process.

Dec 21, 2008 | Jeep Grand Cherokee Cars & Trucks

1 Answer

1994 Nissan Altima Passenger Door won't open


Since you have the door panel off, pul the rod for the door lock manually inside the door, this should unlock it, if it does not, there is a small push button, basicly a little peice of metal on the latch itself on the door latch inside the door, push it down this should pop the door open, you may need to spray all of the mechinisms with white lithium grease in a arosol can.....

Nov 12, 2008 | 1994 Nissan Altima

1 Answer

Programing garagedoor opener


HOMELINKT UNIVERSAL
TRANSMITTER (IF EQUIPPED)
The HomeLinkt Universal
Transmitter, located underneath
the driver’s visor, provides a
convenient way to replace up to
three hand-held transmitters with
a single built-in device. This
feature will learn the radio
frequency codes of most current
transmitters to operate garage
doors and gates, and can also
control home or office lighting and
security systems (with the
available accessory package).
NEXT
MODE
Controls and features
42
When programming your
HomeLinkt Universal
Transmitter, you will be
operating the garage door or
gate. Be sure that people and
objects are out to the way to
prevent potential harm or
damage.
Do not use the HomeLinkt
Universal Transmitter with any
garage door opener that lacks
safety stop and reverse features as
required by U.S. federal safety
standards (this includes any garage
door opener model manufactured
before April 1, 1982). A garage
door which cannot detect an
object, signaling the door to stop
and reverse, does not meet current
U.S. federal safety standards. For
more information on this matter,
call toll-free: 1–800–355–3515.
Programming
1. Prepare for programming the
HomeLinkt Universal Transmitter
by erasing all three of the factory
default channels by holding down
the two outside controls until the
red light begins to flash (20-30
seconds). Release both controls.
2. Hold the end of your hand-held
transmitter against the HomeLinkt
Universal Transmitter (located on
your visor) while keeping the red
light in view.
Controls and features
43
3. Using both hands, press the
hand-held transmitter control and
the desired channel control on the
HomeLinkt Universal Transmitter.
Do not release the controls until
step 4 has been completed.
4. Hold down both controls until
the red light begins to flash slowly
and then rapidly. Rapid flashing
indicates successful programming
of the new frequency signal.
5. Follow steps 2 through 4 to
program the remaining two
channels.
If you do not successfully program
the HomeLinkt Universal
Transmitter after repeated
attempts, refer to Training a
rolling code
which follows or call
toll-free customer assistance:
1–800–355–3515.

Controls and features
44
Operating the HomeLinkT
Universal Transmitter
Once programmed, the HomeLinkt
Universal Transmitter can be used
in place of hand-held transmitters.
To operate, simply press the
appropriate channel control on the
transmitter (the red light will
illuminate, indicating the signal is
being transmitted).
Controls and features
3. Press the programmed
HomeLinkt control in the vehicle
until the training light on the
garage door receiver turns solid
(1-2 seconds). Release the
HomeLinkt control and repress to
turn off the training light.
4. Press the HomeLinkt control
again. If the garage door activates,
the HomeLinkt Universal
Transmitter has been trained to
the receiver.
Erasing channels
To erase all three programmed
channels:
1. Hold down the two outside
controls until the red light begins
to flash.
2. Release both controls.
Channels cannot be erased
individually, but can be
reprogrammed. Refer to
Programming for instructions.

Oct 21, 2008 | 1999 Lincoln Town Car

1 Answer

1999 NISSAN ALTIMA KEYLESS REMOTE PROGRAMMING


1999-2003
Enter vehicle, close and lock all doors.
slowly insert and remove key from ignition 6 times within 10 seconds. The tail lamps will flash to indicate original code has been erased. Turn ignition to the ACC position.
Press any button on 1st transmitter.
Hazard lamps will flash to confirm programming.
TO enter additional transmitters, unlock then lock the doors using the power lock switch located on the driver door.
Press any button on additional transmitter (up to 4 tansmitters total possible). Hazard lamps will flash to confirm programming.
open the driver's door.
Turn ignition off.

You must re-program all existing transmitters as this process erases codes from car.

Jun 25, 2008 | 1999 Nissan Altima

Not finding what you are looking for?
2004 Nissan Altima Logo

389 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...