Question about 1999 Chevrolet Venture

1 Answer

99 chevy venture tether strap anchors?

We just bought a stage 2 car seat( 20-40 lbs) & want to make sure its properly installed. I took it to the dealership today because I couldn't locate the tether strap anchors. However they had no idea either. They said that they could put them in but.... maybe not & encouraged me to consider buying a whole new seat. They directed me to the police station across the road because they said they couldn't just put the anchors in & that the police would know where to put the anchors. The police station however said they have nothing to do with that. It is up to the garage/manufacturor. I have tried to find the information online. One article said that 'the tether anchor brackets will not neccesarily look like the ones used for add-on anchors. Some will be short straight U shaped bars'.
There is a small bar resembling this under the seats but I'm not sure if this is an anchor or if it is just part of the bar that you squeeze to remove the seats.
Could you let me know if the '99 Chevy Venture come with anchor brackets ? Thanks, Bonnie

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 161 Answers

No none of the ventures come with anchor brackets

Posted on Aug 27, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cannot fold down my rear seat to access the child seat anchors. is there any way to release the rear seat from the boot?


Child Seat Restraints - FSB Forums - FullSizeBronco.com

www.fullsizebronco.com/forum/23.../182333-child-seat-restraints.html
Sep 22, 2010 - My rear seat hasnt been mounted in 6 years and my son Wyatt has ....Join Date: Oct 2006 .... Tether Strap Anchor Attachment for the Second Row Center Seating ... With the rear seat folded forward, remove the bolt retaining the rear ..... If you can't track down the part, send me a PM and I will get my Ford ...

Solution for car seat anchor tether - Tundra Solutions

www.tundrasolutions.com/.../119126-solution-for-car-seat-anchor-tether/
Dec 11, 2007 - I have a 2004 Tundra and I just installed a forward facing convertible carseat. It's almost impossible to get the tether strap attached to the ...

Child Car Seat Fitment in Trucks ' IH8MUD Forum


Dec 02, 2015 | 2006 Rover 75 Connoiseur

2 Answers

Convertible car seat


Your owner's manual should explain how to install a car seat. If not, you can go to a GM or Chevy dealer and ask for assistance. This is a mandatory safety problem they should not charge you to just assist in installing the seat.

Oct 21, 2013 | 2005 Chevrolet Equinox

1 Answer

We just bought a 1999 ford explorer eddie bauer edition and i want to put a child car seat in middle section of the back seat, but i cant find the tether ring to attached the seat to. Where is it located,...


Child seat tethers didn't start coming into play until around 2002-2003, however there are anchor kits available for about $50 from Ford Dealerships. When you call to talk to the dealer about availability, start with the service department. They can can check you Vehicle Identification Number (which is on your insurance or registration), and you may be eligible to have them installed under Ford warranty, even after 11 years!

May 04, 2011 | 1999 Ford Explorer

1 Answer

Truck lock is jammed by briefcase strap. can i get into the trunk from the back seat? such as does the back seat fold down?


I searched the owner's manual and there was no mention of folding the rear seats down. If you don't have a manual, you can get one here: http://www.extendedgmwarranty.com/owners-manual/buick/1999-Buick-Century.pdf

You can remove the seats following the instructions below from autozone.com.
Rear Seats
SEAT CUSHION


jturcotte_98.gif

Fig. Typical W-Body rear seat cushion removal

  1. Locate and remove the small bolts at the front lower edge of the seat cushion.
  2. Pull the tabs on the rear cushion retainers.
  3. Remove the seat cushion by lifting up and pulling out of the retainer.
  4. Installation is the reverse of the removal procedure. Make sure the retainer tabs are snapped into place. Tighten the bolts to 18 ft. lbs. (25 Nm).

SEAT BACK


jturcotte_99.gif

Fig. Typical W-Body rear seat back removal

  1. Remove the seat cushion as described above.
  2. Remove the anchor nuts securing the rear seat retainer at the bottom of the seat back.
  3. Grasp the bottom of the seat back and swing upward to disengage the offsets on the upper frame bar from the hangers.
  4. Lift the seat back upwards to remove from the vehicle.
  5. Installation is the reverse of the removal process. Make sure the hooks on the seat back are properly installed to the hangers. Tighten the anchor nuts to 89 inch lbs. (10 Nm).

Nov 07, 2010 | 1999 Buick Century

2 Answers

I do not know how to remove front seat from a 1994 chevrolet beretta cp


hmm,, ok,, try this..

1.) look under the seat you will notice two sliding rods,, on this there are 4 brackets with bolts.. its maybe hidden under the upholestry,, any way remove the bolts,, slide any lift seat..

Oct 12, 2010 | Chevrolet Beretta Cars & Trucks

1 Answer

I have a 1999 chevy blazer I cannot close the


The sunroof is powered by the same circuit breaker that power's your power window, so if your windows work than the circuit breaker should be good. You needed test the switch to verify if works with; on the factory sunroof system the roof is controled by a sunroof module the module receives a signal from the switch then throws voltage to the sunroof motor. The motor and module are located between the sunroof assembly and windshield underneath the head liner. You would reconnected the switch and test to see if the sunroof motor is getting power when the switch is in use by testing the dark green wire when closing and a light green wire when opening. Test these wires at the sunroof motor with a ohm meter or test light. Also, check this procedure to repair...

GM S-Series Pick-ups and SUV's 1994-1999 Repair Guide Power Sunroof - REMOVAL & INSTALLATION

Glass
  1. Close the sunroof and open the sunshade.
  2. If the piece of glass being removed is to be reinstalled, mark the location of the screws, this will ensure proper alignment during installation.
  3. Unfassten the screw that attach the sunroof glass to the sunroof assembly.
  4. Remove the glass from the vehicle.
To install:
  1. Place the glass into position and install the screws that retain the glass. Do not fully tighten the screws just yet.
  2. Adjust the glass so that the fit between the glass and the opening is equal at all four sides. The rear edge of the glass may be slightly higher than the front edge to reduce the wind noise.
  3. After the glass has been adjusted, tighten the screws to 31 inch lbs. (3.5 Nm).
  4. Check the operation and fit of the glass.

Motor
  1. Disconnect the negative battery cable.
  2. Remove the sunroof opening trim by starting at the **** joint and pulling the trim strip from the sunroof opening.
  3. Remove the headlines as follows:
    1. If equipped, remove the overhead or sunroof console.
    2. If equipped, remove the dome lamp.
    3. Remove the coat hooks and the assist handles.
    4. Remove the sunshade-to-roof screws, while pulling down on the sunshade base, push in on the extended screws, loosen the screw that attaches sunshade to the roof and pull down on the sunshade retainer while pushing in on the extended screw. Remove the retainer.
    5. Remove the windshield garnish moldings using trim removal tool J 38778 or its equivalent. Pull the molding away from the pillar and up to remove it.
    6. On four door models, remove the body lock pillar trim panels.
    7. Remove the roof rear header garnish molding using the trim removal tool. Insert the tool into the front edge of the trim and work along the front of the panel, from one end to the other. Unplug the cargo lamp electrical connection and remove the trim.
    8. On two door models, remove the rear seat upper seat belt anchor bolts.
    9. Remove the upper and lower front seat belt anchor bolts.
    10. Remove the rear seat belt lower anchor nut (two door models only).
    11. Remove the end gate or liftgate opening sill plate.
    12. Remove the jack storage cover (left side).
    13. Remove the upper body side trim panel screw (left side).
    14. Remove the upper body side trim panel and the body side front lower trim panel.
    15. Remove the headliner from the vehicle.
  4. Remove the sunroof console mounting bracket.
  5. Remove the straps that retain the wiring harness.
  6. Tag and unplug any necessary electrical connections.
  7. Unfasten the screws that attach the motor to the sunroof assembly.
  8. Remove the motor from the vehicle. Make sure that you do not move the sunroof mechanism while the motor is not in place.
To install:
  1. Place the motor into position and install the retaining screws. Tighten the screws to 31 inch lbs. (3.5 Nm).
  2. Attach all electrical connections that were unplugged.
  3. Attach the straps that retain the wiring harness.
  4. Install the sunroof console mounting bracket.
New headliners must be pierced to accommodate actual vehicle accessories.
  1. Install the headliner as follows:
    1. Install the body side front lower trim panel and the upper body side trim panel.
    2. Install the upper body side trim panel screw (left side).
    3. Install the jack storage cover (left side).
    4. Install the end gate or liftgate opening sill plate.
    5. Install the rear seat belt lower anchor nut (two door models only). Tighten to 59 ft. lbs. (80 Nm).
    6. Install the upper and lower front seat belt anchor bolts. Tighten the bolts to 52 ft. lbs. (70 Nm).
    7. On two door models, install the rear seat upper seat belt anchor bolts. Tighten the bolts to 52 ft. lbs. (70 Nm).
    8. Install the roof rear header garnish molding. Attach the cargo lamp electrical connection, place the trim in position and engage the molding retainers.
    9. On four door models, install the body lock pillar trim panels.
    10. Install the windshield garnish moldings. Place the molding into position, align the retainer clips with the slots and press into place.
    11. Place the sunshade retainer in position, install the screw and tighten to 10 inch lbs. (1.1 Nm). Position the sunshade, install the screws and tighten to 10 inch lbs. (1.1 Nm).
    12. Install the coat hooks and the assist handles.
    13. If equipped, install the dome lamp.
    14. If equipped, install the overhead or sunroof console.
  2. Install the sunroof opening trim. Start the trim in the center of the front of the sunroof opening and work around the perimeter.

Hope helps (remember rated this) Good luck.

Jun 03, 2010 | 1999 Chevrolet Blazer

1 Answer

Where is the latch for the top strap of the car seat


At the roof, near the rear liftgate door, remove the child safety seat tether anchor cover.

0e20029.gif

Jun 28, 2009 | 2005 Ford Escape

1 Answer

HI i own a 1999 susuki vitara 4x4 2 dr. I am


The anchor points on the 2door are located just inside the rear door under the metal strip at the edge of the carpet, they usually have holes in the metal strip with plastic plugs covering them, move the back seat fully backward and tilt it back to suit the safety seat.
ps.. my kids are both in booster seats now, and prefer the vitara to the car! :-)

Jun 11, 2009 | 1999 Suzuki Vitara

1 Answer

Child seat tether anchors


This site shows all the recalls for the car. It says there was a recall b/c of the instructions manual and how to use the anchors. Hopefully this will help.

http://www.internetautoguide.com/auto-recalls/09-int/2000/dodge/intrepid/index.html

Aug 15, 2008 | 2000 Dodge Intrepid

Not finding what you are looking for?
1999 Chevrolet Venture Logo

294 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8274 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...