Question about 1997 Oldsmobile Cutlass Supreme

1 Answer

How do i replace ignition lock for 97 cutlass supreme? How do I get to the screw that holds it into place so it can be removed?

Posted by on

  • Uriel Tello
    Uriel Tello May 11, 2010

    it do not have a screw to hold it ... the screws are to hold the plastic cover around the steering column. to pull the lock u need to turn the ignition lock cylinder to engine running not cranking. and there is a small pin to be pushed in to release the lock... write me back if u have any questions

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

Remove the steering wheel, air bag and coil.

Posted on Aug 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i remove and replace an key ignition on a 92 oldsmoble cutlass supreme....


Just a heads up, if you are changing the ignition due to security failure, there are other ways to fix this.
http://vatspasslockpasskeysecurityhelp.yolasite.com/

Apr 28, 2011 | 1992 Oldsmobile Cutlass Supreme

1 Answer

1986 Cutlass Supreme: how to remove car stereo...


take all the screws out of the panel around the radio, pop off the piece, then remove the screws holding the radio in. take the radio out, pull out the plug in the back and now you can remove it completely.

May 17, 2010 | 1986 Oldsmobile Cutlass Supreme

1 Answer

1993 Cutlass Supreme S 4 door sedan Drivers side front door locked when door was open, the locking mechanism is stuck is stuck and the door can not be closed. How can this be fixedd?


take a screwdriver and put in gap of mechanism and apply pressure while lifting door handle the latch should open if it falls back means spring is broken on latch will need to remove door panel and the 3 screws that hold it in place can get a replacement at a salvage yard for a few bucks

Dec 14, 2009 | 1993 Oldsmobile Cutlass Supreme

1 Answer

I need to replace turn signal switch on 97 olds cutlass supreme.


Disconnect the battery to do any service on the steering column or front radiator areas.

Jun 30, 2009 | 1997 Oldsmobile Cutlass Supreme

1 Answer

How to change a battery in a 1996 Oldsmobile Cutlass Supreme Coup


The bar is there to hold the battery in place, there is a rod that connects to the bar, and a nut on the end of the rod. Remove the nut, then remove the bar, and then replace the battery

Jun 11, 2009 | 1996 Oldsmobile Cutlass Supreme Coupe

1 Answer

How to remove brake light cover from 97 cutlass supreme


Open the trunk and fold back the fabric that covers the plastic wing-nuts that hold the lens in place. Unscrew each of the wing-nuts and push out the light by the studs.

Apr 25, 2009 | 1997 Oldsmobile Cutlass Supreme

1 Answer

I need to replace some dash lights in '87 cutlass supreme


The other screws are behind the woodgrain panels on either side of the speedometer cluster. The panels are held in place with metal clips and are difficult to pry loose. I did it by using a small plastic wedge that I found in a junk pile and once I had a place to start, I worked each corner of both panels until pried out. These panels could break, so go slow and be patient.

Jan 18, 2009 | 1987 Oldsmobile Cutlass Supreme

1 Answer

Need to change ignition but have no key 1995 olds cutlas serria


diconnect battery and wait 30 minutes, then remove steering whell and then remove clip holding lock plate, remove plate and unscrew, usually three screws and remove the turn signal sir coil assembly, then you will see a bolt that is holding the lock cylinder in, it will have 2 wires attached to it and they must be disconnected at the base of the steering column and routed up through the column, then replace parts in reverse order, do not spin the sir coil or you will have to replaqce it

Nov 25, 2008 | 1989 Oldsmobile Cutlass Supreme

1 Answer

1991 Cutlass Ciera


you need to remove the steering wheel with a puller then remove the screw holding the blinker lever now remove the three screws holding the directional switch you will need a special tool to remove the steering lock ring if you don't have this tool you can not remove it after you remove the ring remove the buzzer contacts and remove the screw for the ignition cylinder and put in new cylinder

Oct 18, 2008 | 1991 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
1997 Oldsmobile Cutlass Supreme Logo

Related Topics:

287 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...