My car started knocking. i removed all the car parts found the rod that was loose. Now i want to replace the bearing. can I purchase just a single bearing set

Internal damage to the engine. Usually a knocking is a loose piston rod that connects to the crankshaft. When the rod bearing gets too worn, it causes the rod to become loose around the crankshaft, and you get that horrible knocking noise or rattle. The engine has to be rebuilt (very expensive) or a replacement engine must be found.
If the knocking is loud, and not a ticking (valves or valve lifters), then it won't be long before the engine is destroyed. Too much pressure on the loose rod-soon it may come apart and blow a hole in your block from the rod disintegrating. Not a pretty sight!

Engine Noises ' Knocking and Ticking ' Common Causes

www.justautorepair.com/whats-wrong-with-my.../knocking-ticking

The following are causes of connecting rod bearing noise: ... Loose torque converter-to-flywheel or flywheel-to-crankshaft bolts will sound similar to bearing knock. .... I got a 1998 tahoe its making a lil ticking noise after I got unstuck on some ice ... 2001 FordTaurus with a loud mechanical noise that is constant when engine ...

Change 4.6L rod bearings with engine still in vehicle? 02 Explorer ...

www.ford-trucks.com > ... > Modular V8 (4.6L, 5.4L)

Aug 11, 2011 - The regular everyday rattling noises seemed to get louder than usual. ...So I dropped the pan and this is what I found: ... Is it possible to change the rod bearings with the engine still in the vehicle? ... If you decide to go with new bearings,torque your caps down on some plasti-gauge and see if you get the ... 7.3 engine r&r
Mar 22, 2012
Rod Bearing Replacement
Dec 27, 2010
More results from www.ford-trucks.com

If its a knocking sound:

A KNOCKING SOUND IN THE ENGINE IS MOST LIKELY CAUSED BY ONE OF THE FOLLOWING
1. PISTON SLAP: Makes a sharp metallic noise. Idle engine and short out each cylinder plug. The noise will disappear when plug with bad piston is shorted. Noise will also disappear at acceleration. This can be caused by worn or out of round cylinder, or broken piston ring. Correct problem by re-boring cylinder and/or replacing piston.
2. VALVE NOISE: Makes clicking or rattle noise. Caused by excessive wear on valve stem or lifter, out of adjustment, or stuck valve. Correct by adjusting valve clearance, replace worn valve or lifter, regrind cam, replace valve guide and /or valve. A stuck valve can sometimes be loosened by passing oil through the carburetor while engine is running.

3. ROD BEARING KNOCK: Makes sharp metallic noise similar to a piston slap. Detection is opposite of piston slap. Rod knock is not heard at idle. Knock becomes louder as engine speed is increased. Caused by excessive rod bearing clearance. Correct by adjusting rod bearing clearance to .0015 inches by removing shims. May require re-pouring rod bearing.
4. REAR MAIN BEARING KNOCK: Makes dull knocking or thud noise. Detected at speeds between 20 and 50 MPH. Knock will normally decrease or disappear while pulling or decelerating. Noise will be detected the loudest at normal driving speed, when not pulling or decelerating. Correct by adjusting bearing clearance to .001 to .0015 inches. If knock is excessive, crank should be checked for out of roundness. May need to re-pour all main bearings to correct.
5. TIMING GEAR KNOCK: usually the most difficult to diagnose. If gear is loose or badly worn it will knock in all ranges. Run engine slightly above idle speed. Slowly open and close throttle. Knock will continue to be present, but just as engine slows down knock will become a slight rattle. Remove timing pin and reinsert into timing hole on timing gear cover. Press timing pin tightly against timing gear and accelerate slightly above idle. Knock will significantly be reduced or disappear. Correct by replacing both timing gear and crank gear as a matched set. The two gears should have a backlash clearance of .003 to .004. If more than .009 inch backlash, an oversize (.005) timing gear should be installed.
6. WRIST PIN SLAP: This can not be detected by shorting out the cylinder plugs. Rapidly accelerate and decelerate the engine speed. The engine will pass through a certain speed range when the wrist pin will rattle at about the same pitch as a valve tappet noise. This can be corrected by installing a new wrist pin bushing in the rod or new wrist pin f badly worn. Wrist pin should fit the piston and connecting rod with a tight metal to metal fit. The pin can be pushed into the piston and rod with a slight pressure of the hand. Pin to rod clearance is .0003 to .0005 inches.

A KNOCKING SOUND IN THE ENGINE IS MOST LIKELY CAUSED BY ONE OF THE FOLLOWING
1. PISTON SLAP: Makes a sharp metallic noise. Idle engine and short out each cylinder plug. The noise will disappear when plug with bad piston is shorted. Noise will also disappear at acceleration. This can be caused by worn or out of round cylinder, or broken piston ring. Correct problem by re-boring cylinder and/or replacing piston.
2. VALVE NOISE: Makes clicking or rattle noise. Caused by excessive wear on valve stem or lifter, out of adjustment, or stuck valve. Correct by adjusting valve clearance, replace worn valve or lifter, regrind cam, replace valve guide and /or valve. A stuck valve can sometimes be loosened by passing oil through the carburetor while engine is running.

3. ROD BEARING KNOCK: Makes sharp metallic noise similar to a piston slap. Detection is opposite of piston slap. Rod knock is not heard at idle. Knock becomes louder as engine speed is increased. Caused by excessive rod bearing clearance. Correct by adjusting rod bearing clearance to .0015 inches by removing shims. May require re-pouring rod bearing.
4. REAR MAIN BEARING KNOCK: Makes dull knocking or thud noise. Detected at speeds between 20 and 50 MPH. Knock will normally decrease or disappear while pulling or decelerating. Noise will be detected the loudest at normal driving speed, when not pulling or decelerating. Correct by adjusting bearing clearance to .001 to .0015 inches. If knock is excessive, crank should be checked for out of roundness. May need to re-pour all main bearings to correct.
5. TIMING GEAR KNOCK: usually the most difficult to diagnose. If gear is loose or badly worn it will knock in all ranges. Run engine slightly above idle speed. Slowly open and close throttle. Knock will continue to be present, but just as engine slows down knock will become a slight rattle. Remove timing pin and reinsert into timing hole on timing gear cover. Press timing pin tightly against timing gear and accelerate slightly above idle. Knock will significantly be reduced or disappear. Correct by replacing both timing gear and crank gear as a matched set. The two gears should have a backlash clearance of .003 to .004. If more than .009 inch backlash, an oversize (.005) timing gear should be installed.
6. WRIST PIN SLAP: This can not be detected by shorting out the cylinder plugs. Rapidly accelerate and decelerate the engine speed. The engine will pass through a certain speed range when the wrist pin will rattle at about the same pitch as a valve tappet noise. This can be corrected by installing a new wrist pin bushing in the rod or new wrist pin f badly worn. Wrist pin should fit the piston and connecting rod with a tight metal to metal fit. The pin can be pushed into the piston and rod with a slight pressure of the hand. Pin to rod clearance is .0003 to .0005 inches.

A KNOCKING SOUND IN THE ENGINE IS MOST LIKELY CAUSED BY ONE OF THE FOLLOWING
1. PISTON SLAP: Makes a sharp metallic noise. Idle engine and short out each cylinder plug. The noise will disappear when plug with bad piston is shorted. Noise will also disappear at acceleration. This can be caused by worn or out of round cylinder, or broken piston ring. Correct problem by re-boring cylinder and/or replacing piston.
2. VALVE NOISE: Makes clicking or rattle noise. Caused by excessive wear on valve stem or lifter, out of adjustment, or stuck valve. Correct by adjusting valve clearance, replace worn valve or lifter, regrind cam, replace valve guide and /or valve. A stuck valve can sometimes be loosened by passing oil through the carburetor while engine is running.

3. ROD BEARING KNOCK: Makes sharp metallic noise similar to a piston slap. Detection is opposite of piston slap. Rod knock is not heard at idle. Knock becomes louder as engine speed is increased. Caused by excessive rod bearing clearance. Correct by adjusting rod bearing clearance to .0015 inches by removing shims. May require re-pouring rod bearing.
4. REAR MAIN BEARING KNOCK: Makes dull knocking or thud noise. Detected at speeds between 20 and 50 MPH. Knock will normally decrease or disappear while pulling or decelerating. Noise will be detected the loudest at normal driving speed, when not pulling or decelerating. Correct by adjusting bearing clearance to .001 to .0015 inches. If knock is excessive, crank should be checked for out of roundness. May need to re-pour all main bearings to correct.
5. TIMING GEAR KNOCK: usually the most difficult to diagnose. If gear is loose or badly worn it will knock in all ranges. Run engine slightly above idle speed. Slowly open and close throttle. Knock will continue to be present, but just as engine slows down knock will become a slight rattle. Remove timing pin and reinsert into timing hole on timing gear cover. Press timing pin tightly against timing gear and accelerate slightly above idle. Knock will significantly be reduced or disappear. Correct by replacing both timing gear and crank gear as a matched set. The two gears should have a backlash clearance of .003 to .004. If more than .009 inch backlash, an oversize (.005) timing gear should be installed.
6. WRIST PIN SLAP: This can not be detected by shorting out the cylinder plugs. Rapidly accelerate and decelerate the engine speed. The engine will pass through a certain speed range when the wrist pin will rattle at about the same pitch as a valve tappet noise. This can be corrected by installing a new wrist pin bushing in the rod or new wrist pin f badly worn. Wrist pin should fit the piston and connecting rod with a tight metal to metal fit. The pin can be pushed into the piston and rod with a slight pressure of the hand. Pin to rod clearance is .0003 to .0005 inches.

what is the motor from? Typically if you changed out all those parts already and its still a heavy knock, you're looking at crank bearings. How did you change the connecting rod bearings without the crank bearings? or are you referring to something else? I would assume its connecting rod bearings are the issue, if main bearings go you would see an issue in oil pressure.

There are several reasons why you would hear a loud knock from the engine, and the knock will usually be either in the top end or in the lower or bottom end of the engine.

The first thing that should be done is to drain the engine oil, and then pour the oil filter into a pan where you can see it, and if there is a lot of metal flakes, or a fine cloud of brass floating in the engine oil, you will not want to waste the time or the money trying to repair that engine by dropping the oil pan and replacing the piston rod bearings, it will only be a very temporary patch at best, that is if the patch even lasts for a day.

If you do find metal flakes in the engine oil and oil filter, the piston rod bearings will not be the only bearings in the engine that will need to be replaced, and the crankshaft main bearings can only be replaced by removing the engine and placing it upside-down on a good engine stand. The biggest problem would be that even if you did successfully replace the piston rod and crankshaft main bearings, it would only take one piece of metal flake that was left over in the engine block to find its way to one of your new bearings and then it will take no time at all before that engine will be right back where you started, and that is how important just the cleaning process is in repairing or replacing internal engine components.

If you do not find any metal in the engine oil or oil filter, then you should attempt to find the actual cause of the knock before you decide how to repair the engine, and you will have to remove the engine oil pan to inspect the rod bearings, and if you do remove the engine oil pan make sure that when you inspect the rod bearings that you only do so one at a time because you can not mix up the rod caps, and be very sure that when you remove a rod cap that you do replace it the same way that it came off, and if you turn around the rod cap and install it the wrong way or scratch the crankshaft bearing surface the rod bearing will fail.

If you can hear the knocking louder from under the vehicle then the most likely causes for a lower end engine knock are a damaged piston, worn out piston rod bearings, a broken piston rod, a broken flex-plate, and sometimes loose torque converter to flex-plate bolts, and the only parts that you can really check out without opening up the engine would be a broken flex-plate, or for any loose torque converter to flex-plate bolts.

If you can hear the knocking more from the top of the engine, then the most likely causes for an upper engine knock would be a faulty lifter, or broken rocker arm, or a broken valve spring allowing the valve to contact the piston, and it will require the removal of the valve covers and possibly the intake manifold to inspect for the problem.

If you have any doubts then it would be a good idea to consider a good used engine that you can hear run before you buy it, or a rebuilt engine for that vehicle.

I hope that this information will help you out and save you some time and a lot of money.

Knocking sounds in the lower engine area usually are from loose/damaged connecting rod bearings. Repairs are centered around resurfacing or replacing the crankshaft and the associated bearings. (many penny!)

you have a ROD knock,,,,the oil level can be good and compression can be good,but the bearing on the rod to crank is shot and now has too much play and is causing excessive play and noise,soon the rod will come out the block and seize the engine,,if its knocking that loud then its too late to fix it,,your gonna have to replace the engine really soon,,,sorry but its normal of the dohc engine to do this usually between 90 to 130k miles they let loose but the single cam dont have this issue

Lots of clanking when first started sounds like a worn rod bearing. Check the engine compartment and rev engine to listen for knocking. It will get progressively worse as time goes by. Nothing to do except buy/install new crankshaft kit from autozone, about $300+.

In the mean time, just change oil and put in some oil additive to lessen the knocking. High speeds will accelerate the wear of the rod bearing. The rod bearing is installed inside of the piston rod. This bearing goes around the crankshaft. It has very tight tolerances down to the thousands of an inch. When it gets worn, metal will flake off of the soft bearing material and contaminate your oil more. If you catch it early enough, you can replace the bearing without too much trouble. Here is what you need to do.

Find the bad bearing. If you hear the knocking with the engine on and under the hood, disconnect a sparkplug. If the knocking goes away, that is the bad bearing. Do this disconnecting/reconnecting until you identify the bad bearings. Now disconnect battery. Next loosen drive belt- done from steering pump. Loosen 2-13mm bolts on back, one on top and one on bracket on bottom. On bottom right-hand side of pump will be a long adjusting bolt. Loosen turn this bolt counter clockwise to loosen drive belt. Now jack vehicle from the frame, vehicle will raise but tires will remain on ground. keep going as high as your jack will go. Install jack stands on frame. This extends your suspension and keep body raised. Drain oil, remove steering damper. It's the shock absorber looking thing connected to your tie rods/center link. The easiest way to remove the oil pan is to get a 3/8 inch socket adapter for a cordless drill. The bolts will come out in a hurry if you do this. Keep track of where the double sided bolts are, they secure the fuel line brackets. After all are removed, wiggle, tug, and pull pan out. Now you will see the large main caps and the rod caps. The mains are bolted to the block and the rods will rotate up and down with the spinning of the crankshaft. Spin the crankshaft to see. Each bearing cap needs to be marked. Use a center punch and hammer to mark from front to rear. 1 mark for rod cap 1 and so forth. You should end up with 6 marks on rod cap #6. Do the marking on the front side of the cap so you know how it fits back. Remove the rod caps that corresponded to the bad bearing identified earlier. Remove nut on cap. Wiggle cap back and forth until it comes loose. It will eventually come out. Inside the cap, you will see the bearing. It is basically a liner for the cap that rides on the crankshaft. there is one on the top of the rod too. Remove it by pushing rod up into cylinder and pulling it out with your hand. Ensure you remember the orientation of the bearings. One side has a notch, the other has a key that fits into a hole on the rod. Now you have the bearing in hand, check for scoring, or wearing on the face. Check the web for a nice color picture. Feel the crankshaft bearing area with your finger nail. It should be smooth and not ridged. Purchase some plastigage along with a standard .000 bearing. Clean rod surface, install new bearing and plastigage. Tighten to torque. Remove cap and measure plastigage for your oil clearance. Now you can purchase the correct bearing to match your oil clearance. If you don't have a repair manual, now's a good time to get it. It has bearing tolerances for you to get the correct bearing. After you have the correct bearings, use oil additive to grease up the new bearing/crank surfaces. Put everything back together, put some quality magnets inside of your oil pan near the drain hole and cross your fingers.