Question about 1998 Ford Taurus

1 Answer

Replace right rear break light - 1998 Ford Taurus

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 2,984 Answers

PLEASE DON'T FORGET TO RATE!!!

Signal & Marker Lights Removal & Installation Rear Lamp Assembly Sedan To Remove:

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove the luggage compartment quarter trim panels.
  3. Disconnect the rear lamp assembly electrical connector.
  4. Remove the lamp assembly mounting nuts.
  5. Pull the lamp assembly away from the body.
  6. Disconnect the rear lamp assembly bulb connectors.
  7. Remove the rear lamp assembly.
replace right rear break light - 6753524.gif
To Install:
CAUTION
To prevent water from entering the luggage compartment, make sure the rubber grommet is fully seated.
  1. Position the rear lamp assembly near the body and connect the bulb connectors.
  2. Install the lamp assembly into the body.
  3. Install the lamp assembly mounting nuts. Tighten to 53 in-lbs (6 Nm).
  4. Connect the rear lamp assembly electrical connector.
  5. Install the luggage compartment quarter trim panels.

Posted on Jul 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2002 Chevrolet suburban all my light's are not right turn on the signals they flash fast hit break the break lights dim every light on the back blinks when the signal is on help.


A fast signal is telling you that a bulb is not working. The unit is set up on amount of resistance that sets the speed. Most likely it is the rear light housing board is cracked. Remove the rear light and open the panel from the back. If this is the problem replace the whole fixture. Note very expensive on Amazon.

Apr 17, 2015 | 2002 Chevrolet Suburban

1 Answer

Right rear break light doesnt come on


check the ground wire that is most likely the problem. also on some there is a fuse rare but sometimes there is one .

Jan 13, 2014 | 2005 Volkswagen Sharan 1.9

1 Answer

2001 jaguar s type - Right tail lamp failure message.... I replaced bulbs and fuse and tail lights still don't work but the dual element right break light does illuminate when I press the break also right...


There is a harness that you unplugged for the rear tail lamp. Make sure it is fully pressed and locked. This is always the cause on jags for tail lamp failure.

Dec 14, 2010 | 2001 Jaguar S-Type

2 Answers

How to replace right rear stop and tail light?


Should have acsess to lightbulbs in trunk of car.

Open trunk and remove any carpet or cover around light area.

Bulb should be in a socket,turn socket until it comes out of light lens.

Jan 11, 2010 | 2002 Jaguar X-Type

1 Answer

Just the top rear break light works , 01 grand cheerokee


Break lights go through the turn signal switch in the steering column. Look there for broken parts OR missing power to the switch....... Hope for a blown fuse or burnt wire.

Sep 03, 2009 | 2000 Jeep Grand Cherokee

2 Answers

Signal lights dont work when breaking


No,this is not normal,this normal when the emergency flashers are on,but not the turn signals.Check the bulbs(all of them)in the rear tail light assembleys.If you can not tell which bulbs are bad,replace them all.Does this vehicle have a trailer light plug?If it does,it could be in it.After the bulb replacement(look at bulbs in your hand to see if filiments are burned)replace the turn signal flasher.To find it turn key on,and left or right turn signal on,and listen,and feel for it under dash around the steering column.

Aug 23, 2009 | 1988 Jeep Comanche

1 Answer

When braking, green turn signal lights up and right rear brake light does not come on. (have replaced brake light)


Do you have a trailer harness? If so, your harness has a short in it.
Remove it and throw it away; cheaper to replace it than to repair it.

If not, you have a short in the socket at the brake lamp

May 04, 2009 | 2008 Toyota Sienna

1 Answer

Right read blinker/break light dont work, turn signal blinks rapidly


It's the bulb. There are two filliments in the bulb. One is for when you turn your lights on and the other is for breaking and blinker flashing. When the break filliment goes bad it causes the blinker to flash very rapidly. 100% the bulb. Change it and all will be good again. P.S. if it were a fuse none of the break lights or blinkers would work.

Apr 20, 2009 | 2005 Ford Explorer

2 Answers

Changed break line but still have no pressure in breaks


to do a complete job. you need to bleed all 4 wheels, starting from Right Rear. Right front. Left Rear. Left Front.

Apr 07, 2009 | 1995 Chevrolet Silverado 2500

Not finding what you are looking for?
1998 Ford Taurus Logo

Related Topics:

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...