Question about Chrysler Voyager

1 Answer

Where is the blower resistor located on a 1999 voyager and how do you replace it?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 131 Answers

Remove glovebox or just below. Heater core is there and the blower resistor looks like a computer PCMCIA network card. 2 screws pull out.

Posted on Sep 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We just bought a heater control resister. We can't locate where it goes.


If you locate the blower motor on the passenger side under the dash, if you follow the wires up from the blower motor they should lead you right to the resistor. Its normally only a few inches away from the blower motor.

Nov 21, 2010 | 1999 Plymouth Voyager

2 Answers

Location of ru916


If you are asking about the blower motor resistor for the heater fan? The resistor block is located on the passenger side of firewall under the hood The resistor block is pried out of its location under the wiper module, you may or may not have to move the wiper module to get it out.

Nov 08, 2010 | 1999 Plymouth Grand Voyager

1 Answer

1999 voyager heater motor worked on high then not at all


Sounds like resistor gone for blower motor. Should be located under hood, passenger side behind strut tower on firewall. Little tight to get in there, remove 2 screws and slide it hard to one side and pull out at opposite end hard.

Nov 06, 2010 | 1999 Plymouth Grand Voyager

1 Answer

My 2001 Voyager blower fan only runs on high.


This is 100% the Blower (Fan) Motor Resistor located near the Blower Motor.
This is a very common problem with Chyrsler, Dodge, Plymouth. The key symptom is the Fan only working on High.
This is very easy to access and replace.

Let me know if this helped....

May 11, 2010 | 1999 Chrysler Sebring

1 Answer

'99 Plymouth Grand Voyager fan switch issues


The problem is not with the switch, it's the blower motor resistor. The resistor is usually located in duct work near the blower motor. It will have 4or 5 wires going to it and is held in place with a couple screws. These things generate heat, so they put them in duct work so the fan blows air across them to keep them cool. Sometimes the plug gets hot and melts, you should be able to buy the resitor and the plug with wires (pig tail) from an auto parts store or a dealer. The resistors are usually about $50 the pig tail is about $30.

Dec 02, 2009 | 1999 Plymouth Grand Voyager

1 Answer

Replace resistor connector now blower will not work at all.


Try adding your own ground wire to the motor to see if it will run that way,if so,follow the harness until you get to the bad spot or connection and repair it.

Nov 05, 2009 | 1999 Plymouth Grand Voyager

1 Answer

The fan only works when you turn it on high.


this is caused by a failed part called a blower motor speed control dropping resistor, the resistor is located behind the glove box next to the blower motor, has a large wire connector going to it.

Oct 27, 2009 | 1999 Plymouth Grand Voyager

1 Answer

Location needed for blower senser on 99 plymouth voyager


the blower resistor is under the hood at the firewall on pass side... there are no screws just tabs holding it in place... the pigtail is usually needed when the resistor goes bad it melts the harness

Feb 12, 2009 | 1999 Plymouth Grand Voyager

7 Answers

Heater Control Switch Only Works on High


Your problem is probably a part called the heater resistor block or board. When this part burns out you will only have high speed on the fan. On my 1999 voyager it is located on the firewall and it snaps in a hole in the firewall. This is under the hood behind the alternator.
Mine had a multi pin black plug plugged into it. Unplug the plug and
you should be able to pull the block out insert new block and plug plug back in and it should come to life.

Jun 05, 2008 | 2001 Chrysler Voyager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...