Question about 2002 Mercedes-Benz S-Class

1 Answer

2002 Mercedes Benz S600 Torque on Upper Intake

What is the spec on torque for the bolts on the upper intake of a 2002 Mercedes S600 (V12)?

Posted by on

  • Anonymous Mar 19, 2014

    adjust time

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Mercedes-Benz Expert
  • 489 Answers

That is the intake manifold and there are 3 stages for it , I will list for you the 3 stages :
1st stage M6 Nm 8 M8 Nm 20
2nd stage M6 Nm 8
3rd stage M6 90 degree
Hope it helps

Posted on Aug 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

03 Dodge Intrepid intake manifold torque specs top & bottom is for 3.5 V6


Lower Intake:
  1. Use a skin coat of RTV silicone on both sides of the water passage ports (outer most holes) and put the new lower intake gaskets into place
  2. Hand tighten the 13mm head intake bolts and Torque the bolts , starting from the center and working your way out in a circular pattern
  3. Torque these bolts in a few small increments until they have reached 250 inch pounds of torque.
  4. Upper Intake Plenum:
  5. When installing the intake air plenum , be sure to catch the four center bolts and the two side bolts (stiffener brackets) before tightening , The center bolts should be torqued to 250 inch pounds .The fuel rail bolts should be torqued to 100 inch pounds

Jun 24, 2016 | 2003 Dodge Intrepid

1 Answer

Torque sequence 3400 engine upper intake


starting at the middle bolt and go directly across then criss cross the pattern like you would tightening wheel nuts, towards the outside(end) bolts. if this is a plastic upper intake the torque should be around 15ft lbs if its metal around 25ft lbs.

Sep 04, 2014 | Chevrolet Venture Cars & Trucks

1 Answer

What are the torque specs on a 2002 toyota sienna's spark plugs, air intake manifold, and valve covers? Thank you.


Spark plug torque on the 3.0L engine is 13 ft.lbs. and the 3.3L is 18 ft.lbs.

Valve covers-69 inch lbs.

Intake Manifold-11 ft. lbs.

Jul 07, 2014 | 2002 Toyota Sienna

1 Answer

Intake manifold torque specs.


It is criss cross from front to back around 15 foot pounds so snugging them with a ratchet should do the trick

May 17, 2014 | 2008 Mercedes-Benz Mercedes Benz C Class

1 Answer

Need the torque specs for the upper intake bults on a 2002 chrysler sebring conv. 2.7L


4022caa.jpg

Fig. Intake manifold bolt torque sequence 2.7L engine

Upper intake manifold with a new gasket on the lower intake manifold and torque the bolts, in sequence, to: 105 inch lbs. (12 Nm)

Hope helps (remember to rate this answer). Good job.

Oct 11, 2010 | 2002 Chrysler Sebring

1 Answer

Im looking for torque specs and bolt sequence for the upper intake on a 2002 diamante, 3.5


The intake is not a high torque part, it is usually just put down with normal ratchet tightness and alternating sequence of the bolts. You tighten stuff more than torque specs anyway by hand, you don't even know it. the only thing I have ever used my torque wrench on is the heads, and sometimes I don't even use it there. I always go back to check later anyway. Hope this helps.

Sep 05, 2010 | 2002 Mitsubishi Diamante

2 Answers

Need torque specs for 2000 chevy malibu 3.1 cyl heads & intake


(step 1 ) the torque specs for the heads are---1998 through 2001 are 37 foot lbs. ( step 2) rotate an additional 90-degrees (1/4 turn). intake manifold bolts ( lower ) step 1-- 62 in-lbs, step 2--115 in-lbs. intake manifold bolts/studs ( upper ) 18 ft-lbs. this is for the 3.1 v-6, have a good day!

Aug 14, 2010 | 2000 Chevrolet Malibu

1 Answer

Intake manifold bolts torque and rocker arm torque


Intake Manifold Coolant Pipe Bolt .... 89 in lbs (7.4166 ft. lbs)
Lower Intake Manifold Bolt .............. 115 in. lbs (9.5833 ft. lbs)
Upper Intake Manifold Bolt/Stud ...... 18 ft. lbs
Valve Rocker Arm Bolt ................... 168 in. lbs (14 ft. lbs +30 degress

Feb 06, 2010 | 1999 Buick Century

Not finding what you are looking for?
2002 Mercedes-Benz S-Class Logo

358 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...