Question about 2005 Chrysler PT Cruiser

1 Answer

Where is the clutch master cylinder - 2005 Chrysler PT Cruiser

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

The master cylinder is usually the same as the brake fluid container, the slave cylinder if you have one, is down the line closer to the tranny

Posted on Jul 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where to check clutch fluid level on 2004 mini


the clutch fluid reservoir is at the clutch master cylinder or is an extension of the brake master cylinder
look for a hose from the clutch master cylinder to the brake master cylinder reservoir

Dec 28, 2015 | 2004 Mini Cooper

2 Answers

2006 chevrolet cobalt clutch issues


Just because the master is new does not mean it isn't faulty. If you are certain you have bleed all the air from the system, I suspect you got a bad master.

Nov 21, 2012 | 2006 Chevrolet Cobalt

1 Answer

2006 chevrolet cobalt clutch issues


check clutch installment procedure could be the problem how it was installed.

Nov 21, 2012 | 2006 Chevrolet Cobalt

1 Answer

Cant find the clutch reservoir on my audi a4 1.8 eastate r reg..


The Clutch Master Cylinder is located on the firewall inside the engine bay, and usually next to the brake master cylinder as the brake and clutch pedals are usually very close to one another. The Clutch Master Cylinder is responsible for transferring the clutch pedal pressure hydraulically to the slave cylinder to release the clutch. You can tell when your clutch master cylinder is dying or needs repair when you depress your clutch pedal and it slowly sinks to the floor and does not return. Since the entire system is a hydraulic one, the master cylinder also has a reservoir that holds the fluid used in the clutch hydraulic system. If you decide to change the clutch master cylinder it is a good idea to also get a clutch slave cylinder at the same time, as both units typically fail around the same time. When replacing your master or slave cylinder, its always a good idea to flush your entire system to prevent water buildup or air pockets from being present when you are driving. Also always keep an eye on the fluid in your reservoir, dirty fluid may mean that the internal seals are allowing dirt and contaminants into your master cylinder.

Oct 11, 2011 | 1997 Audi A4

2 Answers

Clutch suddenly has no resistance and car won't shift gears. Fluids were low, have put fluid in the reservoir but still doesn't work. How do you bleed a clutch line?


on the transmission there is a slave cylinder that works like a brake cylinder, when you apply pressure to the clutch pedal a rod inside the vehicle under the dash pushes into a clutch master cylinder, (almost like a brake master cylinder without the reservoir, as the clutch master cylinder works off the brake master cylinders reservoir) the plunger in the clutch master cylinder applies fluid pressure to the slave cylinder,(located down on the trans near the clutch fork assembly) which projects a piston rod into the clutch fork dis-engaging the clutch. To bleed the clutch slave cylinder locate the bleeder screw on the slave cylinder,break loose so it loosens and tightens easily. Check fluid in brake master cylinder reservoir,fill if needed, while bleeder on the slave cyl is closed have a helper push clutch pedal to floor and back 7-8 times, (At first the clutch might stay at the floor, just pull it up by hand or foot and continue) after several pumps with no rest time push pedal to the floor and hold down with foot pressure, at this time loosen the bleeder on slave untill fluid leaks out, watch for air bubbles, close bleeder and repeat untill there is no sign of air bubbles, (make sure to check fluid in the brake master cylinder and keep fill as needed, do not let fluid get less than 1/2 empty as it might **** air and you will have to start over) If this does not bring clutch to operate then you need to check if slave cylinder is reachig its full extension of push rod or not. If it is not then you will have to replace the clutch master cyl or the clutch slave cyl or both as seals are bad and wont hold pressure. Or you need to inspect the clutch fork,the throw-out bearing, or the pressure plate fingers and clutch plate for failure or broken bent parts. I hope it turns out to be a easy fix on that clutching thing.

Jan 14, 2011 | 1995 Nissan Pickup

1 Answer

Is there any way to adjust the clutch on 2006 Kia Spectra5?


YOU HAVE HYDRALIC CLUTCH WHICH IS A CLUTCH MASTER CYLINDER WITH SLAVE CYLINDER.IF YOU HAVING CLUTCH PROBLEMS.CLUTCH IS WORN AND SLIPPING OR YOU HAVE LOW FLUID LEVEL IN CLUTCH MASTER CYLINDER.WHICH CAUSES AIR GET IN HYDRALIC SYSTEM.CAUSING CLUTCH PROBLEMS.IF CLUTCH MASTER CYLINDER IS LOW ON FLUID.CHECK HYDRALIC LINE ON SLAVE CYLINDER TO CLUTCH MASTER CYLINDER FOR FLUID LEAKS.

Aug 03, 2010 | 2007 Kia Spectra5

1 Answer

Clutch pedal drops to the floor with no real effort. How do I check the master cylinder?


CLUTCH AND MASTER CYLINDER SHARE THE SAME RESERVOIR YOU CHECK LEVEL IN THE MASTER CYLINDER.ADD BRAKE FLUID TO THE MAX LINE DONT OVER FILL.IF MASTER CYLINDER RESERVOIR IS EMPTY.CHECK FOR FLUID LEAKS AT CLUTCH LINES AND CONNECTIONS AT CLUTCH RELEASE CYLINDER AND CHECK BRAKE LINES - CALIPERS - WHEEL CYLINDERS AND BRAKE BOOSTER.FIX LEAKS AND BLEED BRAKE AND CLUTCH SYSTEM.

Jul 25, 2010 | Cars & Trucks

1 Answer

Are the brake master cylinder and the clutch slave cylinder interconnect in some way? I'm told that the slave cylinder get its fluid from the master cylinder.


The brake system and the clutch master cylinder have the same fluid tank, look at the brake master cylinder fluid tank, on the right hand side about half way up is a hose that goes over to the clutch master cylinder, if fluid level is not above this hose the clutch will stop functioning. If the clutch slave cylinder, mounted on the front side of transmission bellhousing, leaks then the clutch will stop functioning. The slave cylinder has a bleed screw, check these items and fill and bleed as neccessary. Hope this helps, let me know.

Jul 28, 2010 | 1995 Ford Escort

2 Answers

UNABLE TO ENGAGE GEARS WHEN ENGINE RUNNING ( CAN ENGAGE GEARS WITH ENGINE OFF ). CLUTCH PEDAL GOES STRAIGHT TO THE FLOOR WHEN PRESSED


Need to have it check could be clutch master cylinder or slave cylinder or hose from clutch master cylinder to slave cylinder.check brake fluid at clutch master cylinder sit next to brake master cylinder if empty could have a leak. fill and pump peddle and look for leak.

Jan 12, 2010 | 2001 Ford Focus

1 Answer

Where is the clutch valve located on a 95 honda accord


clutch master cylinder is located drivers side firewall,right next to brake master cylinder. it has small shot glass size fluid resevoir mounted above it,fluid is fed through hose down into clutch master. clutch master cylinder has a rod mounter on ft of it that goes through firewall and attaches to clutch pedal under dash . clutch slave cylinder is mounted on ft passenger side of transmission assy. most common leak is from master cylinder,you would be able to look under dash ,follow clutch pedal up to where it attatched to clutch master pushrod.follow that rod to wear it meets up to a small 1 1/2" or so rubber boot.fluid will be leaking from that boot if master is leaking.

Jul 03, 2009 | 1995 Honda Accord

Not finding what you are looking for?
2005 Chrysler PT Cruiser Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...