Rear axle miss aligned,didn't mark front bracket car is now pulling to the kerb. how can relocate mounting bracket in place

replace front axle shaft you need to loosen axle nut with vechicle weight on the wheel just unloosen axle nut dont take axle nut all the way off just loosen it enough first remove hub cap to loosen axle nut.once loosen then raise vechicle remove wheel tire.you need to remove loosen brake caliper bolts just move brake caliper out of way support caliper piece of wire dont have to disconnect brake caliper hose just move it aside let it hang with a piece clothe hanger or piece or cord dont hang caliper by brake hose will damage brake hose.you need to remove brake caliper mounting bracket.go ahead remove axle nut.you have to remove steering knuckle bolts pull steering knuckle out of the strut bracket.you can remove front axle shaft by using large pry bar to the inner cv pry inner cv joint use a little leverage front axle should pop out.when you install new axle shaft push it in place until you hear it snap in place try pull by hand make sure half shaft in place. when done axle nut torque is 191 ft lbs.strut bracket bolts torque at 133 ft lbs.if this is your first time working on vechicle let a garage do the job.but buy the new shaft then take it with you for garage to replace be cheaper take own parts help cut down costs for part just pay for labor.

REMOVAL
Disconnect the negative battery cable.
Remove (UPPER RADIATOR CROSS MEMBER) and relocate (UPPER RADIATOR CROSS MEMBER REMOVED) the upper radiator crossmember, (Refer to 23 - BODY/EXTERIOR/RADIATOR CROSSMEMBER - REMOVAL).
Remove the radiator fan module (FAN MODULE IN VEHICLE) (Refer to 7 - COOLING/ENGINE/RADIATOR FAN - REMOVAL).
Remove the wiring harness clip from front mount.
Remove the coolant line clamp bolt (COOLANT LINE BRACKET).
Remove the upper nut from the front mount (FRONT RUBBER MOUNT UPPER NUT).
Remove the upper starter mounting bolt (UPPER STARTER BOLT).
Remove the middle starter bolt (MIDDLE STARTER BOLT).
Raise vehicle and support.
Remove the lower front mount nut (FRONT RUBBER MOUNT IN POSITION).
Raise and support engine (SUPPORT ENGINE).
Remove the lower bracket bolt to transmission (BRACKET TRANS BOLT).
Remove the lower bracket bolt to engine block (BRACKET ENGINE BLOCK BOLT).
Relocate the front mount and bracket.
Disconnect the positive battery cable from starter
Disconnect the solenoid connector from starter.
Remove the lower starter bolt (STARTER LOWER BOLT).
Remove starter from vehicle.

TIMING BELT
Removal
Disconnect negative battery cable. Disconnect intake air temperature sensor connector from intake air duct. Disconnect the air intake tube from the throttle body. Disconnect the breather tube from the valve cover. Remove resonator from throttle body. Remove air filter housing.
Raise and support the vehicle. Remove right front wheel. Remove right front splash shield from wheelwell. Remove serpentine accessory drive belt.
Remove crankshaft pulley bolts. It is NOT necessary to remove crankshaft sprocket center bolt. Remove crankshaft pulley. Lower vehicle.
Support engine assembly from above with Support Fixture (J-28467-B). Remove engine mount bracket from timing belt end of engine.Remove power steering hose clamp bolt, and position hose away from timing belt cover. Remove front timing belt cover. Using crankshaft center bolt, rotate crankshaft one full turn clockwise (as viewed from timing belt end of engine).
Align mark on crankshaft sprocket with notch at bottom of rear timing belt cover. See Fig. 4 . Align camshaft sprocket timing marks with notches on valve cover. See Fig. 5 .
CAUTION: Engine damage could result if camshaft sprockets are not properly aligned with notches on valve cover.
Loosen the automatic tensioner bolt. Use an Allen wrench to rotate tensioner and relieve tension on timing belt. Remove timing belt.
Fig. 4: Aligning Crankshaft Sprocket Timing Mark
Courtesy of DAEWOO MOTOR AMERICA, INC.

Fig. 5: Aligning Camshaft Sprocket Timing Marks
Courtesy of DAEWOO MOTOR AMERICA, INC.

Installation
Ensure crankshaft and camshaft timing marks are still aligned. Install the timing belt. See Fig. 7 . Turn the timing belt tensioner counterclockwise to tension the timing belt. Turn tensioner until the pointer aligns with the notch on the rear timing belt cover. Tighten automatic tensioner bolt to specification. See TORQUE SPECIFICATIONS .
Using crankshaft center bolt, turn crankshaft clockwise (as viewed from timing belt end of engine) 2 full revolutions. Ensure timing belt tensioner pointer is still aligned with notch.
If timing belt tensioner is correctly aligned, install timing belt cover. See Fig. 3 . Install the engine mount bracket on the timing belt end of engine. Position power steering hose in place, and install clamp bolt. Install crankshaft pulley. Install serpentine accessory drive belt.
Install right front splash shield. Install right front wheel. Install air filter housing and resonator. Connect air intake temperature sensor connector. Connect negative battery cable.
Fig. 7: Identifying Timing Belt Routing
Courtesy of DAEWOO MOTOR AMERICA, INC.

here

http://www.2carpros.com/questions/daewoo-leganza-2000-daewoo-leganza-timing-marks

Brake Pads Removal & Installation Front

To Remove:

1. Drain brake fluid to ½ full level in reservoir.
2. Remove the front wheels.
   
   
3. Remove the front brake caliper assembly.
4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
5. Remove the wear indicator from each of the 2 brake pads.

To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.

1. Using a large C clamp or equivalent press piston into the caliper.
2. Apply disc brake grease to the inside of each anti-squeal shim.
3. Install the anti-squeal shims on each pad.
4. Install the pad wear indicator clip to the pads.
5. Install the pads with the pad wear indicator plate facing upward.
6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
7. Install the front wheels.
8. Fill the master cylinder with new clean brake fluid.
9. Pump the brake pedal several times to seat the brake pads.

Rear TMC made rear brake components

TMMK made rear brake components

To Remove:

1. Drain the brake fluid to ½ full level in reservoir.
2. Remove the rear wheels.
3. Remove the caliper slide pins.
4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
5. Remove the rear brake calipers.
6. Remove the 2 brake pads with the anti-squeal shims.
7. Remove the anti-squeal shims and pad wear indicators from brake pads.

To Install:

1. Using a large C clamp or equivalent press the piston into the caliper.
2. Coat both sides of the outer anti-squeal shim with pad grease.
3. Install anti-squeal shims to each pad.
4. Install wear indicators on the 2 brake pads.
5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
   • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
   • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
7. Fill the master cylinder with new clean brake fluid.
8. Pump the brake pedal several times to seat the brake pads.
9. Install the rear wheels.

Brake Rotor Removal & Installation Front To Remove:

1. Remove the front wheels.
2. Remove the front brake caliper assembly.
3. Remove the front brake pads.
4. Remove the 2 bolts and caliper mounting bracket.
5. Place match marks on the disc and axle hub.
6. Remove the front wheel disc.

To Install:

1. Align the match marks and install the front disc.
2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
5. Fill the reservoir with brake fluid.
6. Bleed the brake system.
7. Install the front wheel.

Rear To Remove:

1. Remove the rear wheels.
2. Remove the brake caliper assembly.
3. Remove the brake pads.
4. Remove the 2 bolts and the caliper mounting bracket.
5. Place match marks on the disc and axle hub.
6. Remove the rear disc.

To Install:

1. Align the match marks and install the rear disc.
2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
   • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
   • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
   • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
   • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
5. Fill the reservoir with brake fluid.
6. Bleed the brake system.
7. Install the rear wheel

Halfshaft -sorry but the diagrams didn't paste into the fixya.com window, just the text. Also, this was for a 3.2L engine.
REMOVAL & INSTALLATION

1. Before servicing the vehicle, refer to the precautions in the beginning of
   this section.
   
2. Remove or disconnect the following:
   
   
   
   • Negative battery cable
     
   • Front wheel
     
   • Radiator skid plate
     
   • Transfer case skid plate
     
   • Brake calipers and mounting bracket
     
   • Brake rotor
     
   • Wheel speed sensor
     
   • Steering knuckle
   
   
3. Support the axle housing with a jack. Unbolt the axle mounting bracket and
   remove the halfshaft/bracket assembly.
   To install:
   
   
4. Install or connect the following:
   
   
   
   • Axle/bracket assembly. Tighten the bracket flange bolts to 85 ft. lbs. (116
     Nm) and the bracket mounting bolts to 112 ft. lbs. (152 Nm).
     
   • Steering knuckle
     
   • Wheel speed sensor
     
   • Brake rotor
     
   • Brake caliper and mounting bracket. Tighten the bracket bolts to 115 ft.
     lbs. (155 Nm).
     
   • Transfer case skid plate. Tighten the bolts to 27 ft. lbs. (37 Nm).
     
   • Radiator skid plate. Tighten the bolts to 58 ft. lbs. (78 Nm).
     
   • Front wheel
     
   • Negative battery cable
   
   
5. Check the wheel alignment and adjust as necessary.
   
   
   
   
   
   Fig. 1: Exploded view of the left halfshaft, axle shaft and
   axle disconnect
   
   
   
   
   
   
   
   Fig. 2: Exploded view of the right halfshaft and mounting
   bracket
   
   

1. Release the fuel system pressure using the recommended procedure.
2. Remove the fuel pump unit through the access panel in the floor of the trunk. Drain the fuel tank into a portable fuel siphoning container through the opening in the fuel tank where the fuel pump is mounted.

Prior to disconnecting fuel lines, wrap a shop rag around the connections to absorb any fuel spillage due to residual pressure in the lines.

1. Disconnect negative battery cable.
2. Raise and safely support the vehicle. Remove both rear tires.
3. Remove the exhaust pipe rubber insulators off the mounting studs of the rear of the vehicle and in front of the fuel tank.
4. Using grease pencil or paint marker, place alignment marks on the fuel filler hose, filler tube, vent hose and vent tube.
5. Remove the rear splash shield from the right rear wheel well.
6. Disconnect the fuel filler hose and the vent hose near the fuel filter.

1. Disconnect both ends of the sway bar from the stabilizer links. Use a grease pencil or paint marker to outline the position of the crossmember ends on the frame rail.

1. Remove the crossmember mounting bolts and pull the crossmember down until it stops.

1. Place a transmission jack under the fuel tank to support its weight.

The sway bar bracket bolts must be replaced after loosening or removal. Only use original equipment bolts as replacement.

1. Remove the sway bar mounting bracket, heat shield and fuel tank strap. To prevent the sway bar from falling down, install sway bar mounting bracket with the bolts finger-tight only.

1. Carefully and slowly lower the front of the fuel tank. Slide the tank away from the crossmember while pushing the filler vent and fill tube over the crossmember. Detach any remaining fuel or electrical connections. Lower the fuel tank.

To install:

1. Position the tank on the transmission jack or other suitable lift, with the shield and the tank strap in place. Raise the tank over the crossmember and place it in the proper position. Be sure that the electrical connector, pressure relief/rollover valve hose, fuel supply and return lines are accessible through the opening in the trunk. Check to be sure that nothing is pinched or kinked in any way.
2. Push the vent and the filler tube over the crossmember. Rotate the sway bar into position and install the sway bar brackets.
3. Raise the tank into place and position the sway bar mounting bracket and the tank straps in place. Tighten the bolts to 44 ft. lbs. (60 Nm).
4. Raise the crossmember into position and align with the locating marks made during removal. Install bolts and tighten to 70 ft. lbs. (95 Nm).
5. Reconnect the filler tube and vent tube making sure to align with the marks made during removal.
6. Connect the sway bar ends to the link arms and tighten sway bar mounting nuts to 74 ft. lbs. (100 Nm).
7. Install the exhaust onto the hangers. Install the rear splash shield in the right rear wheel well.
8. Install the rear wheels and lug nuts. Tighten the lug nuts, in a star pattern sequence, to 95-100 ft. lbs. (129-135 Nm).
9. Lower the vehicle.
10. Install the fuel pump module.
11. Connect the fuel supply, return and vent tubes. After installation of the quick-connect fittings, check for proper connection by pulling back on the quick-connect fitting. The tube should lock in place. If the connection is not complete, make sure the black plastic ring is not causing the locking retainer to jam in the release position.
12. Install the fuel pump access cover and gasket. Tighten the fasteners and install the trunk liner.
13. Install the filler cap and reconnect the negative battery cable.
14. With the ignition in the ON position, access the DRB III ASD Fuel System Test to pressurize the fuel system. Check for leaks.

1. Check the rear wheel alignment and adjust, if necessary.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

REMOVAL

1. Disconnect negative battery cable.
2. Raise vehicle on hoist. Remove right front wheel.
3. Remove the right splash shield.
4. Remove accessory drive belts.
5. Remove crankshaft damper
6. Remove the lower torque strut
7. Disconnect exhaust system from manifold.
8. Disconnect A/C pressure switch at rear of compressor housing.
9. Lower vehicle and support engine with a jack.
10. Discharge A/C system and disconnect A/C lines at coupling block
11. Remove upper torque strut
12. Remove screw attaching ground strap to strut bracket.
13. Remove torque strut bracket from strut tower.
14. Remove upper radiator support crossmember
15. Remove power steering pump and bracket. Set pump aside. Do not disconnect lines from pump.</B>
16. With engine properly supported, remove right engine mount through bolt.
17. Raise engine with jack until engine support bracket bolts are accessible.
18. Remove support bracket bolts.
19. Remove support bracket.
20. Remove upper timing belt cover fasteners and remove cover.
21. Remove lower timing belt cover fasteners and remove cover
22. CAUTION: When aligning crankshaft and camshaft timing marks always rotate engine from crankshaft. Camshaft should not be rotated after timing belt is removed. Damage to valve components may occur. Always align timing marks before removing timing belt.
23. Before the removal of the timing belt, rotate crankshaft until the TDC mark on oil pump housing aligns with the TDC mark on crankshaft sprocket (trailing edge of sprocket tooth)
24. NOTE: The crankshaft sprocket TDC mark is located on the trailing edge of the sprocket tooth. Failure to align trailing edge of sprocket tooth to TDC mark on oil pump housing will cause the camshaft timing marks to be misaligned.
25. Install 6 mm Allen wrench into belt tensioner. Before rotating the tensioner, insert the long end of a 1/8” or 3 mm Allen wrench into the pin hole on the front of the tensioner .
26. While rotating the tensioner counterclockwise, push in lightly on the 1/8” or 3 mm Allen wrench, until it slides into the locking hole.
27. Remove timing belt. CAUTION: If timing belt was damaged due to incorrect tracking (alignment), the belt tensioner assembly must be replaced

INSTALLATION

1. Set crankshaft sprocket to TDC by aligning the sprocket with the arrow on the oil pump housing.
2. Set camshafts timing marks so that the exhaust camshaft sprocket is a 1/2 notch below the intake camshaft sprocket
3. CAUTION: Ensure that the arrows on both camshaft sprockets are facing up.
4. Install timing belt. Starting at the crankshaft, go around the water pump sprocket, idler pulley, camshaft sprockets and then around the tensioner
5. Move the exhaust camshaft sprocket counterclockwise to align marks and take up belt slack. NOTE: A new tensioner is held in the wound position by a pull pin.
6. Remove the pull pin or Allen wrench from the belt tensioner.
7. Once the timing belt has been installed and tensioner released, rotate the crankshaft two (2) complete revolutions. Verify that the TDC marks on crankshaft and timing marks on the camshafts are aligned as shown in .
8. Install lower timing belt cover and tighten fasteners to 9 N·m (80 in. lbs.
9. Install upper timing belt cover and tighten fasteners to 9 N·m (80 in. lbs.
10. Install right engine support bracket. Ensure the power steering pump is properly located in mounting location on bracket. Tighten mount bracket bolts to 61 N·m (45 ft. lbs.)
11. Lower engine into mounting position and install right engine mount through bolt. Tighten bolt to 118 N·m (87 ft. lbs.).
12. Install power steering pump and bracket.
13. Install upper radiator support crossmember
14. Install torque strut bracket to strut tower.
15. Connect ground strap to bracket.
16. Install upper torque strut
17. Connect A/C lines. Evacuate and recharge A/C system
18. Raise vehicle.
19. Connect exhaust system to manifold.
20. Connect A/C pressure switch connector.
21. Install crankshaft damper
22. Install accessory drive belts
23. Install lower torque strut
24. Perform torque strut adjustment procedure
25. Install right splash shield.
26. Install right front wheel.
27. Connect negative cable to battery.

sounds like the track has been dismounted....try to pull off the inside door panel and look for any missing or broken bolts on the track itself... the track protrudes down to keep the window on track....if this is not a problem look at the glass itself...roll the window down a little to see the bottom of the glass. makes sure all of the mounting brackets are in place and secure..

Rear Axle Notes

1. Raise and support vehicle.
2. Remove rear wheels.
3. Scribe alignment marks on propeller shaft and axle for proper assembly, then disconnect propeller shaft from axle.
4. Disconnect the track bar from axle mounting bracket.
5. Disconnect parking brake cable at equalizer.
6. Disconnect shock absorbers at axle tubes.
7. Disconnect hydraulic brake hose at rear axle Tee-fitting, then tape ends of hose and fitting to prevent contamination.
8. Disconnect axle vent tube from axle.
9. Remove U-bolts and tie plates.
10. Loosen spring mounting bolts.
11. If equipped, disconnect ABS wiring connections at axle.
12. Support axle with suitable jack.
13. Remove spring-to-shackle attaching bolts and lower spring to the floor.
14. Remove axle assembly.
15. Reverse procedure to install.

Front Axle Notes

1. Raise and support vehicle at frame behind front springs.
2. Remove front wheels.
3. Scribe alignment marks on propeller shaft and axle yoke for proper assembly, then disconnect propeller shaft at axle yoke.
4. Disconnect connecting rod at steering knuckles.
5. Disconnect shock absorbers at axle housing.
6. Remove stabilizer bar connecting links to spring tie plates attaching bolts, if equipped.
7. Disconnect breather tube at axle housing.
8. Disconnect stabilizer bar link bolts at spring clips.
9. Remove disc brake calipers, rotors and brake shields.
10. Remove U-bolts and tie plates.
11. Support axle assembly with suitable jack to relieve spring tension.
12. Loosen rear spring shackle to spring attaching bolts.
13. Remove front spring shackle to spring attaching bolts and lower spring to floor.
14. Remove axle from under vehicle.
15. Reverse procedure to install.

i don't think you have to do any repairs from the top end. I will list most fromFord shop manual. Please rate as Fixya if this answers your questions. Please report back. Good luck.

Section 04-02: Suspension and Wheel Hubs, Rear 1994 Town Car, Crown Victoria/Grand Marquis. Workshop Manual
REMOVAL AND INSTALLATION Spring Rear
Removal

1. Position a hoist under the rear axle housing, and raise the vehicle. Refer to Section 00-02 . Place jackstands under frame side rails.

1. Remove rear stabilizer bar as outlined.

1. Disconnect the lower studs of the two shock absorbers from the mounting brackets on the rear axle assembly .

1. Unsnap the RH parking brake rear cable and conduit (2A635) from RH upper arm retainer before lowering the rear axle assembly .

1. Lower the hoist and axle housing until the rear springs are released.

1. Remove rear spring and rear spring center mounting insulators (5741) from vehicle.
   -----------------------------------------------------------------

Shock Absorber Removal
Raise the vehicle on a hoist. 1. To assist in removing the upper attachment on shock absorbers using a plastic dust tube, place an open end wrench on the hex stamped into the dust tube's metal cap. For shock absorbers with a steel dust tube, simply grasp the tube to prevent stud rotation when loosening the retaining nut.

1. Remove the shock absorber retaining nut, washer, and insulator assembly from the stud on the upper side of the frame. Discard nut. Compress the shock absorber to clear the hole in the frame, and remove the inner insulator and washer from the upper retaining stud.
2. Remove the self-locking retaining nut, and disconnect the shock absorber lower stud from the mounting bracket on the rear axle tube.
3. Perform Shock Absorber Checks. Refer to Section 04-00 to determine shock absorbers performance.

Installation

1. Properly prime the new shock absorber . Refer to Section 04-00 , Shock Absorber Checks.

1. Place the inner washer and rear spring insulator (5536) on the upper retaining stud, and position the shock absorber so that the upper retaining stud enters the hole in the frame. While holding the shock absorber in this position, install a new rear spring insulator , washer and nut assembly on the upper side of the upper frame. Be sure to seat the rear spring insulator in the frame attaching hole. Tighten nut to 34-46 Nm (25-34 lb-ft).

1. Extend the shock absorber , and place the lower stud in the mounting bracket hole on the rear axle assembly housing. Install a new self-locking retaining nut. Tighten nut to 76.5-103.5 Nm (56-76 lb-ft).

1. Lower vehicle.

-----------------------------------------------------------------------------
Arm Lower
Removal
Refer to the illustration in Description and Operation. NOTE: To improve rear axle assembly noise and vibration concerns, the rear suspension should be fastened to the frame and rear axle assembly at the curb height position.
NOTE: If one rear suspension lower arm requires replacement, also replace the opposite rear suspension lower arm .
WARNING: TURN REAR SUSPENSION LEVELER COMPRESSOR SWITCH OFF (IF SO EQUIPPED).
NOTE: If both rear suspension arm and bushings and both rear suspension lower arms are to be removed at the same time, remove both rear springs as outlined under Rear Spring Removal. For air spring removal, refer to Section 04-05 .

1. Mark rear suspension shock absorber relative to protective sleeve with the vehicle in a static, level ground condition.

1. Remove rear stabilizer bar as outlined.

1. Raise the vehicle on a hoist, and place jackstands under the rear axle assembly . Refer to Section 00-02 .

1. Lower the hoist until the shock absorbers are fully extended to relieve rear spring pressure.

1. Support rear axle assembly under differential pinion nose as well as under rear axle assembly .

1. Remove and discard the lower arm pivot bolt and nut from the axle bracket. Then, disengage the rear suspension lower arm from the bracket.

1. Remove and discard the pivot bolt and nut from the frame bracket, and remove the rear suspension lower arm .

-----------------------------------------------------------------
Upper
Removal
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Suspension Bushing Service Set T79P-5638-A1, A2 and A5 Rear Axle Control Arm Bushing Tools T86P-5638-AH
WARNING: TURN OFF REAR SUSPENSION LEVELER COMPRESSOR SWITCH (IF SO EQUIPPED).

1. Raise the vehicle, and support the frame side rails with jackstands. Refer to Section 00-02 .
2. Support the rear axle assembly .
3. Lower the rear axle assembly , and support the rear axle assembly under differential pinion nose as well as under rear axle assembly .
4. Unsnap parking brake rear cable and conduit from upper arm retainer.
5. Remove and discard the nut and bolt retaining the rear suspension arm and bushing to the rear axle assembly housing. Disconnect the rear suspension arm and bushing from the housing.
6. Remove and discard the nut and bolt that secures the rear suspension arm and bushing to the frame bracket, and remove the rear suspension arm and bushing . If upper arm rear bushing is to be replaced, use Suspension Bushing Service Set T79P-5638-A and Rear Axle Control Arm Bushing Tools T86P-5638-AH and the following procedure:
7. Place the upper arm rear bushing remover tool in position, and pull bushing out. Using Suspension Bushing Service Set T79P-5638-A install bushing assembly into bushing ear of rear axle assembly.

------------------------------------------------
Stabilizer Bar
WARNING: TURN OFF REAR SUSPENSION LEVELER COMPRESSOR SWITCH (IF SO EQUIPPED).
Removal

1. Raise vehicle on hoist, and place jackstands under the frame side rails. Refer to Section 00-02 .

1. Lower the hoist and rear axle assembly housing until the shock absorbers are fully extended.

1. Disconnect rear stabilizer bars from rear stabilizer bar link and bushing (5C488) . Remove bolts and stabilizer bar bracket (5486) retaining rear stabilizer bar to rear axle assembly .