Question about 2000 Chrysler Sebring

1 Answer

My signals were working and just quit...i have a flasher battery but dont know where to install it.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Chrysler Master
  • 1,779 Answers

The flasher should be located behind the a/c- heater control panel in the center console. It should just unplug to remove, plug in to replace.

Posted on Jul 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turn signals heater


Did all these problems happen all at one time?? If so you may have a bad body ground. Try running a electrical wire from the (-) negative side of the battery to the body and see if this works. Be sure this wire is to a place with no paint as low voltage electricity will not flow through paint.
A). If not try replacing the turn signal flasher for the turn signal problem. This is usually the culprit and it's easiest and cheapest to replace. The turn signal flasher will be found under the driver side dash next to the hazard flasher. Turn the hazard flasher one to locate it. If you want try swapping the turn signal flasher with the hazard flasher to see if this fixes it. They are the same style flasher.
If this doesn't work you may a faulty turn signal switch or some wiring issues.
B). It could as simple as the head lights bulbs need to be replaced, it's rare but I have seen when both bulbs blew at or near the same time. If your able check the voltage at the head sockets.
C). Could be a bad blower motor or switch. I'm not sure if these models have a resistor block or not. The resister block controls the electrical current going to blower motor which controls the speed of the blower fan.

Sep 11, 2012 | Cars & Trucks

1 Answer

Flashers dont work


Check your fuses and signal relays

Jul 17, 2012 | 2000 Chevrolet Impala

2 Answers

My turn signal is not working nor my harard lights i brought an new four way flasher but dont know where it goes


The relays, fuses and flashers will go in the fuse box under the hood. It will be on the drivers side and just be a black box that you pop opern and it should have the details of what fuse/flasher is on the inside of the cover.

Have a good one!

Feb 24, 2011 | Chrysler 300M Cars & Trucks

1 Answer

Turn Signals quit working


Sounds like the turn signal flasher is going bad. The easy way to find wher the flasher is hidden is turn the turn signal on and find the clicking, that is the flasher. The emergency flashers work fine because they use a different flasher.

May 05, 2010 | 2000 Audi TT

1 Answer

MY TURN SIGNAL QUIT WORKING IS THERE A FLASHER


My service manual states that the '02 T+C has a combination turn signal/hazard flasher/daytime running lights module which is located on the junction block, adjacent to and left of the steering column. To access it, you must remove the steering column lower cover and knee pad panel. There is also a fuse for turn signal/hazard flasher. If none of them work, check the fuse 1st.

Jul 18, 2009 | 2003 Chrysler Town & Country

1 Answer

Turn Signals Quit


Driver side Door Jam To the Right of The FUSE BOX,
Not Sure if you got the first one. dont forget to RATE me Thank You !!

Mar 28, 2009 | 1997 Pontiac Bonneville

1 Answer

Flasher or turn signal switch


Make sure the relay is plugged in all the way. When I replaced mine it was taped in and the new one wouldn't stay in without a little bit of duct tape.

Feb 25, 2009 | 2000 Jeep Cherokee

1 Answer

1994 devilles flasher location


Turn signal flasher module is behind dash left of steering column near chime module. I have a 94 Seville and I had that same problem you need a Turn Signal Flasher Moduel, I forgot the proper term for it but I had to get mine replaced too. When I hit the signals to turn the side light would come on but the signal light wouldn't. Its a little box you get from Cadillac it only cost like $20 - $25 and you get it installed and trust. It'll work again. I just got mine done this week and my car now has turn signals again.

Nov 28, 2008 | 1994 Cadillac DeVille

1 Answer

1992 chev 1500 signal lights and brake lights quit working


If it is the turn signal flasher it should be located in the Front seating area, driver side, driver side of steering column, behind instrument cluster, mounted in convenience center. It is possible that there could be a bad ground too. Flasher would be the first thing to check.

Nov 10, 2008 | 1992 Chevrolet C1500

2 Answers

Turning signals have stoped flashing.


The hazard flasher is located in the convenience center, under the dash, on the left side kick panel. The turn signal flasher is installed in a clamp attached to the base of the steering column support inside the car.
hope this helps!

Jul 25, 2008 | 1996 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
2000 Chrysler Sebring Logo

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...