Can the front clip off a 2005 chevey envoy fit on a 2005 chevy trail blazzer ?

2009 Nissan X-Trail Wagon headlight fitting removal. (Australian version)
Remove the central grill
Trim must be partially removed to allow access to the lower and side attachment points of the headlight fitting.
Remove the black trim around wheel arch on the side of the headlight fitting to be removed or both sides if replacing both assemblies.
Remove the 10mm nut holding the trim upper most and nearest the wheel well.
Remove the nut from the side mounting point and the set screw from the bottom mounting point.
Remove top two set screws and plastic clip from the top mountings.
Disconnect blinker light, head light and park light lamp holders and cables.
Installation is reverse procedure.
NISSAN X-TRAIL T31 (09/2007-07/2010)
https://www.carparts2u.com.au/files/detail.php?id=30196

Your grille and chrome bar are held to your truck with eight clips. You can see the top clips if you look. First VERY GENTLY!!! start pulling your grille until you start popping those clips out. Keep an eye on your chrome bar, because it is clipped into the headlight. GENTLY pull on the chrome bar at the headlight until the clips come off, then work your way over to the other headlight. The goal is to be take your time and be gentle until you have all the clips released. Set your grille aside(be careful not to scratch it). Each head light has two metal tabs on top of it, the outer tabs are slightly hidden in the fender. If you pull these tabs up, it will release the headlight from the frame of the truck(be careful not to let the headlight fall out and scratch your bumper). Once you have the headlight assembly out, you can access the blinker bulb sockets.

try fitting stick on beam correctors on the outside of the headlamps you usally buy them from a mazda dealers parts dept a lot cheaper than fitting headlamps and comply with french and uk law once fitted

This is out of my 06 Murano manual, hope that it helps.

REMOVAL
1. Apply protection tape around outer circumference of front grille (bumper fascia side).
2. Remove front grille-radiator cover clips and remove front grille-radiator cover.
3. Remove clips on upper side of front grille.
4. Remove clips of air duct and remove air duct. Refer to EM-16, "AIR CLEANER AND AIR DUCT" .
5. Pull out grille pawls, and remove front grille assembly.

Installation is the reverse of removal.

good luck

First you need a flathead screwdriver and the socket wrench set.
Pop open the hood and where the grill of the car is should be 4 black clips and you use the flathead screwdriver to take that off. Find the mm sockets that fit on the screws directly above your headlights, one on each side. After that's been taken out, there is one screw on the end of the bumper near the doors. You'd have to get a smaller mm socket to get those out, one on each side. On the bottom are a few more clips and two more screws. Using the same mm sockets that took of the screws above the headlights, take off the screws on the bottom of bumper.

Well you need to take or loosen up the front bumper and grille. tkae out retainers up top and then bolts at fender edges and at the bottom of bumper if you need more go to collisionrepairadvice.com

2 of my 3 2005 Malibus had this issue. Even though the top nut seems tightened, the bulb is a bit forward in the assembly. Try loosening the nut and pushing the bulb back all the way and then re-tighten the nut. If that doesn't work, then the other quick fix is with the tabs on the bottom of the assembly that drop into loose fitting slots on the grill frame. I used some rubber washer/grommets on the tabs to make the tabs fit tightly into the receiving slots so the bulb can't move about.

needed: flathead screwdriver. 10mm socket and wrench, and about 15minutes


You remove the three clips on the grill with a flathead screwdriver. then just pull straight up on the grill to remove. This will expose the bolts for removal of your front bumper. there are also screws on either side of the wheelwell where the bumper meets the fender....all of these are 10mm... then pull out one side of the bumper and the whole thing will come off easily. Also if you have the factory foglights you will need to remove the harnesses from the lights before removing the bumper.....Once the bumper is off the 4 bolts for the headlight are right there for you to see....one under the grillside one one the fender side and 2 on top all of which are 10mm as well....once the headlight is out remove the wiring harnesses and reinstall the new light in exctly the same way but reversed....hope this helps

You have to remove the front bumper and grill etc

There are 5 bolts holding the headlight assembly in place. 2 at the top and 3 underneath.

Remove the plastic cross piece by prising out the clips and then the grille clips too then unbolt the bolts eithr side under the wheel arch. The bumper is still fastened using cips. Pull the bumper forward to unclip.

Plastic rivets in the wheel wells, clips under the headlights, remove the grill, plastic clips under the front,
too much to write.
Go get a repair manual