Question about 2003 Chrysler Sebring

1 Answer

2004 Chrysler Sebring it hesitates when I crank it up in the morning, however once it's been cranked up several times during the day it doesn't hesitate, only on cold starts. What could be wrong

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 295 Answers

The fuel filter should be changed first.
The engine fuel pressure over night is bleeding down into the fuel tank. I would suggest a tune up . If the condition continues after a tune up. The fuel pump is starting to go. You should then have a mechanic check out the fuel system and have the vehicle diagnose.

Posted on Jul 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

04 Chrysler Sebring cranks and won't start. I have changed the plugs, wires, and distributor. I have a 3.0 engine


Standard practice is check for spark at each plug when you crank. If you're getting spark, then check for fuel getting to cylinders.

Feb 06, 2017 | 2004 Chrysler Sebring

1 Answer

I have a 2006 chrysler sebring I just changed the camshaft and cranksensor and it still won't start it just cranks could it be the pcm ?


Chrysler Sebring no crank no start resolved - YouTube

? 1:11
www.youtube.com/watch?v=sCZqeyC5jDQ

Oct 21, 2013 - Uploaded by DanielRau1234
My car would not start. the problem turned out to be a 20 amp fuse. ... This fixed my 2006 Sebring. It's fuse ... My sons chrysler sebring 2004 has the exact same problem! .... Engine Won't Start - No Crank Diagnosis (Troubleshooting Starting System Issues) - Duration: 25:23. by Bushougoma 431,429 views.

Oct 27, 2015 | Chrysler Cars & Trucks

1 Answer

I have no spark on my 1999 chrysler sebring convertable


You will need at least a 12 volt test light to check the cam and crankshaft sensors. If either one is bad, the auto shut down relay will not ground the PCM. Remove the 4 pin electrical connector from the coil. one of the terminals is a 5 volt feed. Connect the light to that terminal and clip the other to ground. Turn the key to the on position. the light should flash once. If it does not flash the problem is in the ASD relay or its circuit. If it flashes once, try to start the engine. (don't worry, it can't start.) See if the light flashes during cranking or not. If not, return the key to off and then disconnect the crank sensor wire connector and try again. If it flashes as you crank the engine now, then the crank sensor is bad. If it does not flash during cranking then the cam sensor is probably bad. They are both easy to access and replace. The PCM could also be bad, but the cam/crank sensors are a more common problem. A repair manual is a cheap investment and could be helpful. Good luck.

Feb 28, 2015 | 1999 Chrysler Sebring LXi

1 Answer

My 2004 sebering sedan cranks but won't start


You need to have spark an fuel an compression for a engine to start an run. You'll have to find out what is missing an then find out why ! Fixing Car That Cranks But Doesn Start Up

Jan 27, 2015 | 2004 Chrysler Sebring

1 Answer

Codes po340 2004 Sebring


DTC code is P0340 no cam signal at PCM. Chrysler always used to say replace the cam and crank sensors together..wouldn't pay our warranty time at dealer unless we replaced both.

Aug 21, 2014 | 2004 Chrysler Sebring

1 Answer

Engine won't turn over


More info is needed. Does the engine CRANK? In other words does the starter spin the engine over but not start? If it fails to crank, it is a starter or battery problem.

Feb 01, 2014 | 2004 Chrysler Sebring Convertible

3 Answers

My 97 Sebring died about a week ago and now it wont start. Found that the it was not firing. Changed the Distributor cap, rotor and distributor, along with the crank sensor. Placed new spark plugs in about...


Did you check the timing belt to see if it broke? It ha a 2.5 and it has belt. Remove timing cover at the front of the engine and have someone crank it while you watch the cam to see if it turns. If it doesn't turn, replace the belt.

Jun 05, 2011 | 1997 Chrysler Sebring

1 Answer

Ignition timing for a 2004 sebring?


The ign timing is set by the computer. The crank and cam have got to be set by the timing belt, but the rest is done by the computer.

If you have "jumped" time then you will need to check/change the timing belt to fix the problem.

Aug 02, 2008 | 2004 Chrysler Sebring

Not finding what you are looking for?
2003 Chrysler Sebring Logo

249 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...