Question about 2000 Ford Expedition

1 Answer

99 model Expedition At first, the air bag was maximum high yesterday. so i disconnected the air supply hose from the bag to release all the air. after that, the air compressor doesn't work anymore... Now, the body is at the lowest position and it feels like there's no suspension at all when i drove the van. Some say air suspension bag is gone, some say G-sencer or level sencer is gone, some say compressor is gone... I've got so confused with this situation. Local auto part dealer advised to replace the whole parts and which cost me around $1,200. please someone help me!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Ford Master
  • 420 Answers

I would say that the leveling sensor is most likely bad. But it won't matter untill you figure out why the compressor isn't working. You need to pick up a service manuel at the parts store, if you don't want to buy one somtimes you can check one out at the library. I am guessing and thats all I'm doing is that the leveling sensor is in front of the compressor and is not giving information to the compressor. Good Luck.

Posted on Jul 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the heater core on 94 mercury cougar


Removing the Old Core
  • Disconnect the Mercury Cougar's negative battery cable. Remove the center console from the interior. Disarm the car's air bag system and remove the bag's diagnostic monitor and bracket.

  • Take the heater outlet floor duct out of the car. Remove the screw holding the air transfer duct and push it into the outlet duct. Unscrew the screws retaining the outlet duct to the heater core cover and release the retaining tabs on each side to remove the duct.

  • Raise and support the Mercury Cougar, using multiple jackstands. Drain the engine coolant by removing the drain plug on the bottom of the radiator. Replace the drain plug after all the liquid flows into a clean container and disconnect the heater hoses from the core

  • Withdraw the black vacuum supply hose from the vacuum source (you can now lower the vehicle). Disconnect the same hose from the air conditioner's vacuum reservoir tank.

  • Detach the heater core cover that holds the core by releasing the retaining tabs and removing the clips. Remove the dash panel seal, vacuum hose and heater core bracket from the cover.

  • Remove the heater core from the cover and the case seal from the core

Dec 20, 2016 | Mercury Cars & Trucks

1 Answer

Rear Air Suspension won't air up


take the sensor arm loose and manually operate it, when it is up, it thinks the suspension is low. Spray the bags and hoses with soapy water to find any leaks, dawn dish detergent works well. repair any leaks. If no leaks manifest, take a hose loose and see if you are actually getting air pressure from the air pump. Just because it is running, doesn't mean it is supplying pressure.

Sep 20, 2012 | 2001 Ford Expedition

1 Answer

How do i take the the steering wheel off 99 silverado 2500


Be sure to deactivate the air bag before working on the steering wheel. I just disconnect both battery connections and let it set 15 minutes. Insert a flat tip screwdriver into each slot on the back of the steering wheel and twist slightly to release air bag retaining clips.Don't do this while sitting in the drivers seat, the bag might go off! Pull the bag off, release the small assurance clip then the connector will pull out of the air bag. Set it in the bed, bag side up so the cover can't become a projectile if it goes off. Pull the horn connector out of the steering wheel. Back the large bolt out most of the way on the steering wheel puller . Bolt the puller to the wheel with 2 bolts and screw the large bolt back into the puller. I tap on the wheel as I screw it in.

Read more: http://wiki.answers.com/Q/How_do_you_remove_the_steering_wheel_on_a_1999_silverado#ixzz23kyUrQD2

Aug 16, 2012 | 1999 Chevrolet Silverado 1500

2 Answers

Where do I adjust the rpm on my 1991 dodge caravan?


you can not manualy set the rpm on your dodge caravan, it is set by your computer and your idle air control valve, if you are having problems with your idle being to high or low you may need to replace your idle air control valve, go to your local auto zone or auto parts store and get a new one, they are pretty easy to replace,just a couple of screws and a electric connection plug, the auto store should be able to give you the location of the part on your vehicle of where it is located.

Jul 01, 2011 | 1991 Dodge Caravan

1 Answer

Air bag code 32


If I'm not mistaken I think it is a shorted or open circuit on one of the sensors. Model and year often helps to isolate the symtom and diagnostics. You will have a 99 percent chance of having a defective clock spring with a code 32 (B1932) but if you want to spend some more money on the diagnostic equipment I can post the complete diagnostic routine.

Possible Causes: Driver air bag high resistance could be caused by:
- a poor connection or corrosion in the driver air bag module circuits or the air bag sliding contact.
- an open circuit or high resistance in the air bag sliding contact windings.
- an open circuit or high resistance in the wiring harness.
- an open circuit or high resistance in the driver air bag module.

Flash code 32 which commonly calls for replacement of the clockspring (air bag contact assembly) under the steering wheel.

Hope helps (remember to rate and comment this).

Nov 04, 2010 | Lincoln LS Cars & Trucks

1 Answer

2001 Ford expedition A.C. work for the rear of the car but not the front, sometimes air blows out but as I accelerate the air stops blowing as I remove my foot from the accelerator it continues blowing,...


This sounds like a vacuum problem. Check your vacuum hoses and connections as they relate to the HVAC system. There is a good chance that you have a cracked, broken, or disconnected hose, or a hose that collapses.

Aug 22, 2010 | 2001 Ford Expedition

1 Answer

I have a 99 ford expedition i replaced the air compressor cause the front air shocks were bad and ruined the compressor. and teh rear air bags went flat now that the new compressor is in the rear wont air...


I have a 2001 Expedition, I don't have air bags in the front, the compressor don't work the air shocks. You have rear leveling. When they replaced the (compressor) did they turn the leveling switch back on. you may have air shocks connected to the compressor. Did the rear go down right after or over a couple of days. If the switch is on, turn it off and jack the rear up quiet a bit, make sure both side are quiet equal with each other, like it would be if it where raised by the air bags. Turn your level switch back on with it jacked up or sitting on stands. It may have went down so much that the compressor can't raise them back up.

Jan 04, 2010 | 1999 Ford Expedition

1 Answer

My 2001 Ford Expedition looses air in the rear air bags after i cut it off. I don't hear any air leaks or anything! What can be the problem?


the air bags release air after it sits. The rear raises back up after starting engine, if you add weight, it raises up even more to compensate for level suspension. It should be fine unless it's sitting almost on thr ground, but it does release air and sit lower.

Dec 16, 2009 | 2001 Ford Expedition

1 Answer

My Rear suspension stop working on my 97 Expedition. The rear Bags are about 6 mos old. The compressor is working. It was working fine yesterday but this morning when I started up my truck and drove away...


sounds like possibly the bags are blown or either lines leaking if it's the bags blown out there are a couple choices replace the bags obviously or you can get an aftermarket kit to do away with the air ride suspension and put regular springs and shocks under it which is alot cheaper than new bags. but make sure you don't have a line that has ruptured

Oct 22, 2009 | 1997 Ford Expedition

1 Answer

Need to repalce a heater core on a 2000 ford expedition where is it how do i get to it.


  1. Disconnect the negative battery cable.

    CAUTION After disconnecting the negative battery cable, wait for 1 minute for the SRS module to deplete its energy.

  2. Drain the cooling system into a clean container for reuse.
  3. Disconnect the heater hoses from the heater core.
  4. Remove the steering column by performing the following procedure:
    • Position the front wheels in the straight-ahead direction.
    • At the both sides of the steering wheel, remove the cover plugs, the steering wheel-to-air bag module screws, disconnect the air bag electrical connector and carefully remove the air bag module.

      CAUTION Safely store the air bag module with the front side facing upward.

    • Remove the steering wheel-to-steering column nut.
    • Using a steering wheel puller, press the steering wheel from the steering column.
    • Remove the parking brake release handle screws and move the release handle aside.
    • Remove the hood release screws and move the hood release aside.
    • Remove the 2 instrument panel-to-steering column cover screws and the cover.
    • Remove the instrument panel steering column opening reinforcement bolts and the reinforcement.
    • Remove the ignition switch bolt and disconnect the ignition switch electrical connector.
    • At the base of the steering column, disconnect the electrical connectors.
    • If equipped with an automatic transmission, remove the transmission range indicator bolt and the cable.
    • If equipped with an automatic transmission, disconnect the shift cable from the steering column shift tube lever and the steering column bracket.
    • Disconnect the brake shift interlock solenoid electrical connector.
    • Remove the air bag sliding contact.
    • Remove the upper intermediate steering shaft-to-column shaft bolt and discard the bolt.
    • Remove the lower steering column-to-instrument panel nuts and the steering column.
  5. Remove the instrument panel by performing the following procedure:
    • Disconnect the Brake Pedal Position (BPP) switch electrical connector.
    • Remove the push pins and remove both cowl side trim panels.
    • At the right side cowl panel, disconnect the electrical connectors and ground wires.
    • Remove both sides windshield garnish moldings.
    • Disconnect the power distribution box from its bracket and move it aside.
    • In the engine compartment, loosen the bulkhead wiring harness bolts and disconnect the electrical connectors.
    • Pull the bulkhead electrical connector handle and disconnect the wiring harness.
    • Remove the passenger’s side air bag module-to-instrument panel screws, disconnect the electrical connector and remove the air bag module.
Store the air bag module in a safe location with the front facing upward.
  • Disconnect the blend door actuator’s electrical connector.
  • Disconnect the climate control vacuum harness connector.
  • Disconnect the radio’s antenna connector.
  • Remove the glove compartment.
  • Remove the instrument panel defroster grille.
  • Remove the upper instrument panel bolts.
  • If equipped, remove the upper series floor console.
  • Under the steering column, remove the instrument panel brace bolt.
  • At both sides, remove the windshield side garnish moldings.
  • Remove both the right and left instrument panel-to-cowl bolts.
  • Remove the fuse panel door.
  • Pull the instrument panel away from the dash.
  • Loosen the instrument panel-to-body harness bolt and disconnect the harness.
  • Using an assistant, remove the instrument panel.
  1. At the PCM, disconnect the electrical connector; then, remove the 2 PCM cover nuts, the cover and the PCM.

    NOTE The PCM is located at the right side of the instrument panel.

  2. Remove the evaporator core by perform the following procedure:
    • Discharge and recover the air conditioning system refrigerant.
    • Remove the refrigerant lines from the evaporator core. Discard the O-rings.
    • Disconnect the air conditioning cycling switch.
    • Disconnect the blower motor electrical connectors.
    • Disconnect the speed control servo connector; then, remove the bolt and reposition the speed control servo.
    • Remove the windshield washer reservoir/coolant recovery reservoir, and move it aside.
    • Disconnect the air conditioning manifold and tube from the accumulator/drier.
    • Disconnect the condenser-to-evaporator tube.
    • Inside the vehicle, disconnect the air conditioning system vacuum harness and the evaporator housing mounting nut.
    • In the passenger’s compartment, remove the evaporator housing-to-chassis nut.
    • In the engine compartment, remove the 3 evaporator housing-to-chassis nuts.
    • Remove the air conditioning accumulator from the evaporator core.
    • If equipped with a 5.0L engine, remove the evaporator housing heat shield screw, clips and the shield.
    • Remove the evaporator housing cover screws and the cover.
    • Remove the evaporator core from the housing.
  3. Remove the PCM ground strap screw and the heat sink.
  4. In the engine compartment, remove the heater housing air plenum nuts.
  5. Remove the heater core-to-air plenum cover screws and the cover.
  6. Remove the heater core.
021d43c.gif

Oct 13, 2009 | 2000 Ford Expedition

Not finding what you are looking for?
2000 Ford Expedition Logo

210 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...