Question about 2004 Volkswagen Passat

1 Answer

P0322 vw passat 2001 ignition distributor, speed input circuit no signal? please and thank you.

Posted by on

  • kimou1dz Jul 25, 2009

    Thank you very much, i have replaced the crankshaft position sensor with a new one, and all the problem is gone, however i still have a new code but has no symtoms except it appears on the screen of the scaner and the morning it doesn't start at first and fails then the second try it starts, then after that it goes fine, what do you think it ld be?

    many appreciations.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 56 Answers

Check Engine Speed Sensor, or cmp
http://forums.vwvortex.com/zerothread?id=2934505

This could be a magnetic or optical sensor. What it does is watches your Crankshaft for TDC (top dead center of the #1 piston) Then Ignition timing can occur because the ecu knows where the #1 piston so it can squirt fuel and ignite the spark. Also works in conjuction to your Camshaft sensor which allows the engine to breath. Note, without Air no combustion will occur in the engine, which gives you a no start condition.

In conclusion, If you find the CKP ( crankshaft sensor) and inspect its wiring. It could be scored since it is on the engine block and Also remove it and do a resistance test, to make sure it isnt broken internally.
If it is wiring Repair as needed
and if it is a faulty Sensor replace it and you should be good to go.

If you have a hard time starting it with out doing all the above, then try to crank the engine with the key for a few seconds, then stop, reverse the key and retry starting it. By this time the engine will have enough fuel vapor and heat that the top piston will ignite forcing the engine to start. Remember CKP only is used for ignition.
GOOD LUCK and keep me informed.

Posted on Jul 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the PO320 code? what is wrong with my 2005 Hyundai xg350L?


P0320 Hyundai Ignition/Distributor Engine Speed Input Circuit Possible causes
- Faulty Ignition/Distributor engine speed sensor
- Faulty Crankshaft Position sensor
- Ignition/Distributor engine speed sensor harness is open or shorted
- Ignition/Distributor engine speed sensor circuit poor electrical connection
- Low battery charge
- Faulty Engine Control Module (ECM)
What about the obd code?
The P0320 Hyundai code is triggered when the Engine Control Module (ECM) detects that there is no current at the ignition coil group
Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Lack/Loss of Power
- The engine may be harder to start
- The engine may stumble or stall
P0320 Hyundai Description
Ignition failure sensor is used to check whether the spark ignition is occurred correctly or not and also used to tachometer drive. The sensor monitors the voltage difference between a resistance which is on the battery circuit for ignition coil. When the ignition coil works properly, the electric current through the resistance is detected as voltage drop. This is confirmed for every ignition event with the crankshaft sensor and the camshaft sensor. If ECM detects a malfunction, no ignition is possible, so the engine would not start. If there is no ignition signal for a predetermined cycle for one or two ignition coils, an ignition coil circuit failure exists.

Nov 17, 2014 | Hyundai Motor 2005 XG350

1 Answer

P0320 code


P0320 KIA - Ignition/Distributor Engine Speed Input Circuit

Possible causes - Faulty Ignition/Distributor engine speed sensor
- Faulty Crankshaft Position sensor
- Ignition/Distributor engine speed sensor harness is open or shorted
- Ignition/Distributor engine speed sensor circuit poor electrical connection
- Low battery charge
- Faulty Engine Control Module (ECM)

Apr 10, 2014 | 2004 Kia Optima

1 Answer

P0321 and p0322 on a 02 passat


Trouble Code: P0321

Ignition/Distributor Engine Speed Input Circuit Range/Performance

Possible Causes:


Engine speed sensor has failed or is damaged.ECM has failed.Sensor wheel is damaged or doesn-t fit properly.Sensor wheel spacer isn-t seated properly.


Trouble Code: P0322

Ignition/Distributor Engine Input Circuit No Signal

Possible Causes:


Engine speed sensor has failed or is damaged.ECM has failed.Sensor wheel is damaged or doesn-t fit properly.Sensor wheel spacer isn-t seated properly.

Nov 18, 2012 | Volkswagen Cars & Trucks

1 Answer

2002 vw passat epc light comes on and when slowing down engine shuts down showing code 0322 what is my problem


Code P0322 states: Ignition/ Distributor Engine speed input circuit NO SIGNAL. the sensor is on the left side(as you sit in the vehicle) of the engine block near the transmission flange. Know this, codes do not tell you if the part is bad necessarily just where to look. Wires and connectors can fail too. I don't know how to test this sensor without a scan tool, the good kind. Which i don't have.

Oct 10, 2012 | 2002 Volkswagen Passat

1 Answer

P0322,P1544,P0121


The fault code P0322 means "Ignition/Distributor Engine Speed Input Circuit No Signal"
The P1544 means "Seat Direction Switch Assembly Circuit Open"
The P0121 means "Throttle/Pedal Position Sensor/Switch A Circuit Range/Performance Problem"
when you know the code, you can most likely repair it yourself.
_______________________
elm327 bluetooth scanner

Sep 06, 2012 | Volkswagen Cabrio Cars & Trucks

2 Answers

I have a 2004 VW Passat the engine light came on had it diagnosed the code is P0322 what does it mean and how is it fixed? Thanks


Symptoms- Engine Light ON (or Service Engine Soon Warning Light)
- Lack/Loss of Power
- The engine may be harder to start
- The engine may stumble or stallPossible causes- Ignition/Distributor engine speed sensor harness circuit is open or shorted
- Ignition/Distributor engine speed sensor poor electrical connection
- Faulty Ignition/Distributor engine speed sensor
- Faulty Crankshaft Position sensor
- Low battery charge
- Faulty Engine Control Module (ECM)When is the code detected?The P0322 code is triggered when the Engine Control Module (ECM) detects no signal.P0322 VOLKSWAGEN DescriptionIgnition failure sensor is used to check whether the spark ignition is occurred correctly or not and also used to tachometer drive. The sensor monitors the voltage difference between a resistance which is on the battery circuit for ignition coil. When the ignition coil works properly, the electric current through the resistance is detected as voltage drop. This is confirmed for every ignition event with the crankshaft sensor and the camshaft sensor. If ECM detects a malfunction, no ignition is possible, so the engine would not start. If there is no ignition signal for a predetermined cycle for one or two ignition coils, an ignition coil circuit failure exists.

Nov 10, 2011 | 2004 Volkswagen Passat

1 Answer

2006 jetta 2.5 starts late and it doesn't go over 3000 rpm and engine light and epc light on engine code is p0322. Im wondering what could be the problem?


P0322....Ignition/Distributor Engine Speed Input Circuit No Signal

Well sorry to disappoint you but as this is a 2006 vehicle its a dealer only diagnostic software to locate fault then lift the limp mode which is what you have at the moment ,i suspect a a possible fault inside the ECU but it could be a crank or cam sensor if fitted with the later ,Now an american vehicle can have the OBDII read but it may not be possible to reset anything as the europeon version cannot even have the OBDII read let alone reset anything .Its to put general garages out of business so only the dealers can do anything on a modern vehicle .

Mar 01, 2011 | Volkswagen Jetta Cars & Trucks

2 Answers

05 kia amanti with diagnostics codes p0350,p0320,p0300,p0302,p0303,p0304,p0305,p0306.skipping at times.when it does skip & misfire the rpm gauge goes crazy.this problem is not consitant


Generic OBD II Diagnostic Trouble Codes

DTC CODES P0300 to P0399

P0300....Random/Multiple Cylinder Misfire Detected

P0301....Cylinder 1 Misfire Detected

P0302....Cylinder 2 Misfire Detected

P0303....Cylinder 3 Misfire Detected

P0304....Cylinder 4 Misfire Detected

P0305....Cylinder 5 Misfire Detected

P0306....Cylinder 6 Misfire Detected

P0307....Cylinder 7 Misfire Detected

P0308....Cylinder 8 Misfire Detected

P0309....Cylinder 9 Misfire Detected

P0310....Cylinder 10....Misfire Detected

P0311....Cylinder 11 Misfire Detected

P0312....Cylinder 12 Misfire Detected

P0313....Misfire Detected with Low Fuel

P0314....Single Cylinder Misfire (Cylinder not Specified)

P0320....Ignition/Distributor Engine Speed Input Circuit

P0321....Ignition/Distributor Engine Speed Input Circuit Range/Performance

P0322....Ignition/Distributor Engine Speed Input Circuit No Signal

P0323....Ignition/Distributor Engine Speed Input Circuit Intermittent

P0324....Knock Control System Error

P0325....Knock Sensor 1 Circuit (Bank 1 or Single Sensor)

P0326....Knock Sensor 1 Circuit Range/Performance (Bank 1 or Single Sensor)

P0327....Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)

P0328....Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)

P0329....Knock Sensor 1 Circuit Input Intermittent (Bank 1 or Single Sensor)

P0330....Knock Sensor 2 Circuit (Bank 2)

P0331....Knock Sensor 2 Circuit Range/Performance (Bank 2)

P0332....Knock Sensor 2 Circuit Low Input (Bank 2)

P0333....Knock Sensor 2 Circuit High Input (Bank 2)

P0334....Knock Sensor 2 Circuit Input Intermittent (Bank 2)

P0335....Crankshaft Position Sensor A Circuit

P0336....Crankshaft Position Sensor A Circuit Range/Performance

P0337....Crankshaft Position Sensor A Circuit Low Input

P0338....Crankshaft Position Sensor A Circuit High Input

P0339....Crankshaft Position Sensor A Circuit Intermittent

P0340....Camshaft Position Sensor 'A' Circuit (Bank 1 or Single Sensor)

P0341 Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 1 or Single Sensor)

P0342....Camshaft Position Sensor 'A' Circuit Low Input (Bank 1 or Single Sensor)

P0343....Camshaft Position Sensor 'A' Circuit High Input (Bank 1 or Single Sensor)

P0344....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 1 or Single Sensor)

P0345....Camshaft Position Sensor 'A' Circuit (Bank 2)

P0346....Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 2)

P0347....Camshaft Position Sensor 'A' Circuit Low Input (Bank 2)

P0348....Camshaft Position Sensor 'A' Circuit High Input (Bank 2)

P0349....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 2)

P0350....Ignition Coil Primary/Secondary Circuit

Nov 17, 2010 | Kia Amanti Cars & Trucks

1 Answer

I have a 1999 VW golf 2.0 gl code P0322, P0422, and P0303 code. I need help


  • 16706 P0322 Ign./distributor Eng. Speed Inp. Circ No signal
  • 16687 P0303 Cyl. 3 Misfire Detected
  • 16806 P0422 Main Catalyst, Bank 1 Below Threshold
P0322 Could be caused by a faulty Engine Speed Sensor also known as a Crankshaft Pos./Engine Speed Sensor.

P0303 Might have a faulty #3 Fuel Injector, Faulty spark plug and/or faulty spark plug wire and connectors.

P0422 Either your front 02 sensor is faulty and/or your catalytic converter is fried and needs replacing.

Mar 23, 2010 | 2000 Volkswagen Golf

2 Answers

Code reader fault 16706


you need the engine speed sensor. Ask the vendor where the exact location is. This is a foreign Car code.Volks wagon. Looked up the code and somebody else had the problem.

Jan 07, 2009 | 2001 Volkswagen Passat

Not finding what you are looking for?
2004 Volkswagen Passat Logo

3,079 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...