Question about 2006 Toyota Corolla

1 Answer

How to replace front discs (abs) - 2006 Toyota Corolla

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 1,861 Answers

Jack up the vehicle, and place a jack stand under the frame where you are working. Remove the wheel/tire. Observe the caliper. On the back side, remove the bolts that holds the caliper onto the caliper bracket. Suspend the caliper, and try to not stretch or kink the rubber brake hose. Next, remove the bolts that holds the caliper bracket to the metal plate. After the bracket is loose, tap on the backside of the rotor to dislodge it from the hub. This is a very easy procedure.

Posted on Jul 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brakes juddering, not rear drums front discs appear good.


no
the problem most likely is warped discs
this makes the pistons move in and out and pulses under the foot
take the discs to an accredited brake shop and have them checked and machined
ABS systems do not work until a skid situation is reached, then the abs pump cuts in and maintains brake line pressure according to brake pedal pressure
oil on brake lining and disc pads will also give problems so have the shop do a proper inspection

Aug 15, 2016 | Cars & Trucks

1 Answer

What would make the brakes bind up on a 1995 Taurus?


Did you recently replace the front brakes ? If you did them yourself, did you clean and GREASE the front rotor pins that bolt the brake disc holders to the wheel assembly ?They might be rusted in place, and won't let the disc retract or close. Your wheel cylinders might be frozen in place as well.

Jul 23, 2014 | 1995 Ford Taurus

1 Answer

Cannot figure out if my daughters 1996 MX6LS/MEdition has disc brakes or ABS breaks. How can I tell Thanks


Disc brakes and ABS are two totally different things. ABS is a computer system that keeps the brakes from locking up on you. Disc brakes are a type of brake system. The front are disc brakes and the rears are either disc or drum brakes.

Nov 18, 2010 | 1996 Mazda MX-6

1 Answer

Air bag and abs lights staying on


If the Airbag light is on, it indicates that a electronic fault is stored in the memory for the airbag. You will need to have a diagnostic check done to pinpoint what the fault is, have it sorted out and only then can the fault be cleared so the light will go off. The ABS light also indicates a fault on the electronic side of the braking system. If the light comes on as you start the vehicle this indicates that there is an open circuit in the wiring or that the ABS control unit itself is faulty. If the light only comes on once the vehicle is in motion, this indicates that a wheel speed sender is incorrectly fitted or dirty and not sensing the ABS Rotor on one of the wheels. If a CV joint has been replaced, the joint may not have an ABS ring fitted on it.[front] At the rear the ABS pick up is fitted on the inside of the brake discs and must be fitted to the new disc when replacing discs.

Jun 02, 2010 | 1998 Audi A4

1 Answer

97 chevy blazer what is the torque for front disc wheel bearing? I replaced front rotor and now abs light is on?


ABS is electronic, most likely you have a defective wheel speed sensor, there is one at each wheel.

Mar 23, 2010 | Chevrolet Blazer Cars & Trucks

1 Answer

Disc message


Sounds like your front brake discs are worn near to minimum limit. Get them checked out and replaced as necessary.

Aug 11, 2009 | 2004 Volvo C70

1 Answer

2003 s-10. I replaced the front disc brakes and


ABS is designed to seance when the wheels stop rapidly and the car is still moving. if it has kicked in before the wheels lock then i would start at the sensors then if they check out i would check the ABS computer if equipped. If it doesn't have an ABS module then it will be controlled by the ECM " engine control module " Hope this helps. Good luck.

Jun 05, 2009 | 2003 Chevrolet S-10

2 Answers

Daewoo lanos


its the rotors are warped .. if you are saying when applying the brakes they are jerking in the pedal right ?/ its the rotors are warped and need replaced if this is what you are asking .. your abs should be ok i think its rotors ..

Feb 06, 2009 | 2002 Daewoo Lanos

2 Answers

2002 Ford Escape Brake stutter


There is also a Recall on the ABS sensor from Ford. http://auto-recalls.justia.com/content/07V156000-FORD-ESCAPE-2001.html

Jan 13, 2009 | 2002 Ford Escape

Not finding what you are looking for?
2006 Toyota Corolla Logo

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...