Fault cylinder B misfire - 2003 GMC Yukon XL

Misfire cylinder 3 and injector fault cylinder 2

p0306 is misfire with number 6 cylinder P0306 Cylinder 6 Misfire Detected and p1314 cat converter problem P1314 Misfire Rate Catalyst Damage Fault Bank 2 P1314

You need to check that fault code, you have a misfiring engine cylinder. The fault code will indicate which cylinder or cylinders is casing the misfire. Go to any Autozone and have the fault code read, tell them you have a check eng light on.

Hi. You have misfires on cylinders 4, 5 and 6. If there are no faults on cylinder 1, 2 and 3 then I would check the power to the left bank injectors. Also check spark plugs and ht leads. If there are running issues then this should be an easy fix. If the faults are very intermitant then it can be a bit tricky to isolate.

code p0300 refers to--random/multiple cylinder/s misfire detected...Causes---spark plugs---HT leads---injectors---ignition coils ---low compression ---wiring
code p0302 refers to cylinder 2 misfire detected Causes ---engine mechanical fault---wiring---ignition/fuel system ---ECT/MAF sensors ECM
code po303 refers to cylinder 3 misfire detected Causes Engine mechanical fault---wiring---ignition/ fuel system ---injector---ECT/MAF sensor ECM The common fault to all is the fuel/system ignition
I would have the injectors checked and have a pressure test done on the fuel manifold to check pump and fuel regulator valve.

All fault codes can be checked out at http://www.bluejag.co.uk but here are the results for some of yours. You can ignor P1111. Looks like a faulty plug or coil pack cylinder 2

Fault Code:- P1314 Indicates a Power-train fault


The fault is generally due to a problem in the Ignition or Misfire area


Fault Description: Misfire rate catalyst damage -bank 2 NOTE: This DTC will flag only when accompanied by an individual cylinder misfire DTC: P0300 - P0306

Action of ECM:- ECM Default:- Maximum engine speed reduced


After clearing the DTC, complete the Misfire monitor drive cycle
Check for a reoccurrence of fault DTC.

Possible Fault:- Cylinder compression low Worn camshaft / broken valve spring(s) Fuel delivery pressure (low / high) Fuel injector(s) restricted / leaking Fuel injector(s) continuously open Fuel contamination Fuel injector circuit fault(s) (Injector DTCs also flagged) Spark plug failure / fouled / incorrect gap ECM to ignition coil primary circuit fault (Cylinder misfire detected DTC also flagged) Ignition coil failure
Fault Code:- P1316 Indicates a Power-train fault


The fault is generally due to a problem in the Ignition or Misfire area


Fault Description: Misfire excess emission NOTE: This DTC will flag only when accompanied by an individual cylinder misfire DTC: P0300 - P0306

Action of ECM:- none


After clearing the DTC, complete the Misfire monitor drive cycle
Check for a reoccurrence of fault DTC.

Possible Fault:- Cylinder compression low Worn camshaft / broken valve spring(s) Fuel delivery pressure (low / high) Fuel injector(s) restricted / leaking Fuel injector(s) continuously open Fuel contamination Fuel injector circuit fault(s) (Injector DTCs also flagged) Spark plug failure / fouled / incorrect gap ECM to ignition coil primary circuit fault (Cylinder misfire detected DTC also flagged) Ignition coil failure

Fault Code:-
P0302 Indicates a Power-train fault


The fault is generally due to a problem in the Ignition or Misfire area


Fault Description: Misfire detected ?€" cylinder 2

Action of ECM:- none


After clearing the DTC, complete the Misfire monitor drive cycle
Check for a reoccurrence of fault DTC.

Possible Fault:- Refer to P0300 Possible Causes

A flashing Check Engine light means you have a ignition Misfire, start by replacing the spark plugs and spark plug wires, one or more is defective. If you have a electronic engine control fault code reader the cylinder or cylinders that are misfiring will set a fault code, the codes are P0300-P0306, the last number being the number of the cylinder ( cylinders 1-6) the computer has detected a misfire in.

P0301 Cylinder No. 1 Misfire Detected
P0302 Cylinder No. 2 Misfire Detected
P0303 Cylinder No. 3 Misfire Detected
P0304 Cylinder No. 4 Misfire Detected
P0305 Cylinder No. 5 Misfire Detected
P0306 Cylinder No. 6 Misfire Detected
P1346 Variable Valve Timing (VVT) Circuit Range/Performance Fault
P1349 Variable Valve Timing (VVT) System Malfunction
P0330 Knock Sensor
P0446 EVAP Vent Control Fault
P0430 Catalyst System

Stop driving immediately.....

You defiantly skipped on your timing........

P0300 Random Misfire Detected
P0301 Cylinder 1 Misfire Detected
P0302 Cylinder 2 Misfire Detected
P0303 Cylinder 3 Misfire Detected
according to this fault codes first mark ignition coils
3 ---------------- 6
2 ---------------- 5
1 ---------------- 4
RB-------------LB
this right banks and left bank, please remove Ignition coils with lids and spark plugs from right bank and swap with left bank, if fault code change as
P 0304 Cylinder 4 Misfire Detected
P 0305 Cylinder 5 Misfire Detected
P 0306 Cylinder 6 Misfire Detected
You can Identify it's a faulty ignition system then next swap ignition lids from ignition coils be careful each coils have two lids one short and other long bit deference and when you remove and fix it to the car keep in mind correct order because each coil two different fire for two spark plugs don't mix up, if you mix it can create the fault code.if you detect any fault ignition coils or spark plugs or lids replace that and also whether god or bad recommend to replace spark plugs, find the right that's most important thing, if this way couldn't found the any ignition fault next step is check fuel presser, when the engine running fuel presser must be around 4.5 bar without engine running must be 4 to 6 bar if the fuel presser too low need to check two different things one is fuel pump other is fuel injectors, in this case you can swap injectors from right bank to left bank and find is the injectors leaking, if not leaking faulty fuel pump.is this information helped you? if yes please leave a comment,

first code means random/multiple misfire cylinder (s) detected
second code means misfire detected number 1 cylinder, third code, miss=fire number 3 cylinder fourth code misfire number 4 cylinder
causes can be spark plugs, HT leads, ignition coils, injector, wiring fault, low compression/ engine mechanical fault