Question about 1994 Toyota Corolla

2 Answers

Is there any eaiser way to remove the drivers side axle from a toyota corolla besides prying on each side? Also, I have a manual transmission and was curious where to replenish the transmission fluid?

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,559 Answers

No easier way other than paying someone else to do it,Also the fluid fill plug is located half way up the side of the transmission and the drain plug is on the bottom.

Posted on Jul 16, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 288 Answers

First loosen the steering knuckle by unfastening either the tie rod end or the strut. After you've removed the center axle nut, tap the outer end of the axle with a mallet to get it started, then pry it out the rest of teh way. Use a pry bar on the inside end.

Frank
Frank's Friendly Cars Maui Car Rental
www.MauiCarRental.biz

Posted on Aug 30, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i chage a c/v axle on a hyundai tiburon


Specifically for 2003 Tiburon V6 6 speed, but may work for you as well.
-Loosen tire lugs
-Remove center caps with screw driver or similar tool (careful not to scratch caps)
-loosen axle nut

-Jack the car up and place on jack stands
-Chalk rear wheels
-finish removing tire lug nuts and tire
-remove cotter pin and finish removing axle nut
-remove brake pads
-remove caliper and brake assembly
-remove rotor (possible PITA), use extreme caution hammering a stuck rotor!

IMPORTANT STEP:
*remove 2 bolts from strut mount assembly. This will allow you enough clearance to "cleanly" pull axle out with minimal force/hammering. No axle puller tool necessary and no messing with the lower ball joint.

-Now gently tap the axle out of the hub assembly
-pull the rest of the axle out of the hub assembly by hand or pry with long screw driver or pickle fork. Again, since you removed the 2 strut assembly bolts, your hub assembly should have dropped down and away from the axle quit a bit to allow you enough clearance to remove axle from hub assembly

**Follow next steps for DRIVER SIDE ONLY**
-Next, place a fluid pan to catch any leaking trans fluid before removing axle from transmission side.
-Using a long screwdriver or pickle fork, pry the axle away from the transmission
-Remove entire axle and replace with new one
-Installation is reverse of removal steps. (not difficult, just line up the splines and everything should "pop" in place

Jun 09, 2010 | 2003 Hyundai Tiburon

2 Answers

How do you remove the half shafts on a 1993 corolla w 5spd manual trans? I never did this and don't know where to begin. The car has very high miles and isn't worth the cost to have it done at a shop. It...


if you mean "drive axles" you need to remove ball joint from lower control arm and of course big nut on axle end, swing the strut away from car and lower control arm, take pry bar, pry axle out of tranny (it'll click out) then reverse pattern for reassembly (axle must click back into tranny,.....good luck, cracklin joe

Jan 10, 2010 | 1993 Toyota Corolla

1 Answer

1992 Toyota Corolla CV Joint


You can pick up an entire re manufactured axle assembly at your local auto parts store. In order to replace the assembly you will need to disconnect the tie rod end and the ball joint. Remove the spindle nut. Push the axle stub out of the hub. Now with a suitable container under the axle to catch spilled fluid pry the axle from the transmission housing. Install is the reverse of removal. For more detailed instructions and diagrams go to www.autozone.com vehicle repair guides.

Oct 29, 2009 | 1992 Toyota Corolla

2 Answers

1989 toyota corolla base 4-door manual tranny, drivers side drive shaft has play in transmission side, both the driveshaft and transaxle bearings look okay, what else is there? what keeps those shafts...


There is a large lock nut that holds the axle into the splined end inside the transaxle. This nut is usually torqued into place very well though, but if it is loose or was not torqued properly then this could cause free-play in the axle. You can look up the torque specs online or use a chilton or Haynes manual to get the specification.

Oct 16, 2009 | 1989 Toyota Corolla 2 Door

2 Answers

1996 toy corolla cv axle removal


the axles are retained in the diff by a spring clip it is usually not that uasy to release the axles but if you use a small tyre lever between the diff housing and the cv housing and do so gently they should come out.

Jun 21, 2009 | 1996 Toyota Corolla

1 Answer

2003 toyota corolla axle replacement


There is a little spring loaded clip on the end of the axle in the trans. Just uses a pry bar against the trans housing and inner axle joint to pop the axle out.

Apr 03, 2009 | 2003 Toyota Corolla

1 Answer

CV Axle removal and installation


The axle should be able to be removed by using a flat ended pry bar tool with a dull flat end. Or possibly a very large flat screw driver. Put the pry bar between the axle and transmission. With light pressure, the axle should pop out of the transmission. The axle just snaps into the transmission. There should be no need or cause to damage the seal because the seal is inset into the transmission. Just watch what you are doing. As far as replacing the seal, I do not know. I have not had to do that yet, and I have replaced both sides with new boots more than once.

Oct 19, 2008 | 1995 Geo Metro

1 Answer

Do i have to pry the axle out of the transmission


Hello, I guess that you dont have the expensive proper tools for the job and need to improvise without damaging anything?.
Probably the easiest way is to unbolt the bottom balljoint,which allows the strut with brakes attached to swing/hang freely.DO NOT pull on strut to remove axle,that will only damage the c.v joint(you can get away with it sometimes).If you have someone helping,ask them to keep a constant pull/pressure while you are doing the next step.Which is to use two large bladed screwdrivers(or similiar)on opposing sides(eg;top+bottom or left/right etc) of the big black c.v joint coming out of the gearbox.There is a 5mm groove to put the screwdriver into.Apply pressure towards gearbox and the axle will pop out,so will oil.
Hope that helps.

Jun 22, 2008 | 1990 Toyota Corolla

Not finding what you are looking for?
1994 Toyota Corolla Logo

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...