Question about 2005 Chevrolet Malibu

2 Answers

Blower fan resistor module replaced, worked for 2 days quit again

I replaced the blower fan resistor module. The fan then worked for 2 days and then quit on speeds 1 & 2 again. 3& 4 still work. What is taking out the resistor module or is something else causing this problem.

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 166 Answers

Hi you probely have a draging blower motor. if it pulling more than 25 amps replace it and check akk wirring connectors for burn or hot spots. good luck

Posted on Jul 17, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 462 Answers

HIGH RESISTANCE IN THE BLOWER MOTOR CAN CAUSE YOUR PROBLEM, OR A BAD RESISTOR.
THERE IS NO REAL GOOD WAY TO CHECK THE RESISTANCE OF THE BLOWER MOTOR.

Posted on Jul 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2002 saturn blower motor quit working


Right next to it is the resistor,remove connector,remove 2 screws and put new one in and call it the day.

Jun 29, 2015 | 2002 Saturn L-Series

1 Answer

Blower fan control problem


Check the wiring to the motor and resistor pack For the motor to run at full speed all the time indicates that there is uncontrolled voltage to it which means that there is a earth after the motor before the resistor. For the resistor to burn out .Well it requires fan air flow to keep it cool and with the ignition off it must still be getting current to it to earth. I am suspecting a faulty automatic control module. I suggest you have it check out for failure.

Apr 27, 2013 | 2002 Chrysler Town & Country

1 Answer

1998 Buick Century w/ manual control, smelled burning odor and blower motor quit working. Control Module?


blower resistor is common to burn causeing smell. check with dealer, there may be a campain on this problem. if not. replace resistor and harness (pig tail) and blower motor..

Jan 21, 2013 | 1998 Buick Century

1 Answer

1 thru 4 on my blower quit working , with 5 the only setting working , then the ac went out, then 5 quit working a few days later. it just quit working while it was on. what could this be?


This is caused by the blower resistor. Under the passenger dash, behind the glove box. Drop the blower motor, 3 screws and 1 electrical plug. Behind that is the blower resistor module. Cost me $31 for a new one and took about 1/2 hour to change.

Jul 25, 2011 | 2002 Chevrolet Monte Carlo

1 Answer

I have only high speed on my ac/heat switch. have replace acdelco blower motor resistor 2 times already. works for a while and quits. whatelse do I need to check etc?.


If you have replaced the blower motor resistor block twice all ready, i would be replacing the blower motor itself. When the blower motor is drawing too much current it burns out resistors for lower fan speeds in resistor block, but doesnt blow fuse for fan. Also check for leaves and stuff in fan when removing fan.

Jul 18, 2011 | 2006 Isuzu i-280

1 Answer

My air conditioner front blower quit. What could be the problem? The rear blower is working.


Hello, This sounds like a blower Resistor control module that is bad. If you see your front blower fan under the hood, follow the power lines back to a connector in the Firewall. You can try tapping this part with the handle of a screwdriver and it may work again.

If the part does not work, you will need to replace it. The units under the hood are easy to replace. If the fan wires do not go to an underhood connector, then the Resistor would be under the dash and close to the fan.

The part can be obtained from a Salvage yard. A site called car-parts.com will give a range of prices and contact info. You can buy the part new at Autozone, Advance, and Oreillys and they should have diagrams and more info for you.

Jun 23, 2011 | 2001 Ford Explorer

3 Answers

BLOWER FAN NOT WORKING PROPERLY


I had the same problem change your blower motor resistor.

Nov 13, 2008 | 2006 Chevrolet Trailblazer

Not finding what you are looking for?
2005 Chevrolet Malibu Logo

588 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...