Question about 2002 Pontiac Grand Am

1 Answer

Right side headlamp blown & fog lamps do not work

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 51 Answers

Check ground on right side or for a bad wire. bad bulbs also?

Posted on Jul 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi,I have an Alfa 2001 156 cigarette lighter not working found some fuses near the battery but not one for the cigarette lighter


Fuse box in passenger compartment Alfa Romeo 156.
fuse box location.
The fuses for the main devices are housed in a control unit under the dashboard, to the left of the steering column. To gain access to them, remove the panel (A) releasing the tabs (B) in the direction of the arrow below and remove the screw (C).

fuse box layout.

1 Ignition auxiliary circuits relay 1 2 Heated rear window relay 3 Horn relay F1 (10A) RH headlamp- high beam F2 (10A) Headlamp high beam warning lamp, LH headlamp-high beam F3 (20A) Boot lid/tailgate lamp, central locking F4 (10A) Headlamp adjustment, RH headlamp-low beam F5 (30A) Electric windows(front) F6 (10A) LH stop lamp, LH tail lamp, RH licence plate lamp, RH rear fog lamp, RH side lamp F7 (10A) LH licence plate lamp, LH rear fog lamp, LH side lamp, RH stop lamp, RH tail lamp F8 (10A) LH head lamp-low beam F9 (15A) Cigarette lighter, heater/air conditioning (AC) F10 (20A) Wind screen wash/wipe system F11 (20A) Horn F12 (10A) Alarm system, anti-lock brake system (ABS)(with ESP), audio system, instrument panel, interior lamps F13 (10A) Anti-lock brake system (ABS), central locking, electric door mirrors, electric windows, glove box lamp, reversing lamps, stop lamp (high level) F14 (10A) Hazard warning lamps F15 (30A) Door mirror heater, heated rear window

Sep 13, 2017 | Alfa Romeo Cars & Trucks

1 Answer

I have a 94 Chevy Astro van with factory fog lights I need to know where the power comes from on a 30 size of the relay or the fog lights thank you


For the load side of relay, comes from fog lamp fuse. Voltage for control side of relay comes from fog lamp switch which gets voltage from headlamp switch.
fog lamp fuse-j14izskjhmuin2fdgknpgms3-5-0.jpg

Apr 07, 2017 | 1994 Chevrolet Astro

3 Answers

How do I turn on fog lights on a Cadillac escalade esv 09


If it is a turn knob for lights just pull out on knob

Apr 27, 2015 | 2009 Cadillac Escalade ESV

1 Answer

My fog lights won't turn on Nissan sentra GEX 2002


There are several things that can cause your fog lamps to not work. The fog lamp circuits need to be diagnosed. Your entire fog lamp circuit can be tested at the plug for the fog lamp relay located n the relay box.

PIN 5 on the relay should have battery power at all times. This power comes from Fuse #43 (15 Amp) in the fuse and fusible link box in the engine compartment. If there is power at this pin, the fuse and the circuit between the fuse and the relay is good.

PIN 3 on the relay goes to the fog lamp bulbs. There should be continuity to ground through the bulbs on this pin. If you have continuity to ground, connecting a jumper wire between PIN 5 and PIN 3 should make the fog lamps come on unless there is a short circuit to ground, which will cause Fuse #43 to blow. If there is no continuity to ground on this pin, the problem is either that BOTH fog lamp bulbs are burned out or there is a break in the wire between the relay and the bulbs.

PIN 1 Is the battery power for the primary coil in the relay. This power comes from the headlamp switch and power is only supposed to be present here when the headlamps are on and the dimmer switch is on LOW BEAM. If power is not present at this pin, the problem is a bad headlamp switch or an open circuit between the headlamp switch and the relay.

PIN 2 Is the control circuit for the primary relay coil. The control circuit should have continuity to ground when the fog lamp switch is set to the ON position. If there is no continuity to ground with the fog lamp switch on, the problem is a faulty fog lamp switch, an open between the relay and the fog lamp switch, or an open between the fog lamp switch and ground E37 (right front of engine compartment) and ground F7 (left rear of engine compartment) Please note: This circuit has redundant grounds....if one ground is not making good contact, the other ground can still make the circuit work.

PIN 4 on the relay is not used.

If all of the circuits/pins are working as described above, replace the relay.

That is pretty much it... That is all you really need to know to get your fog lamp circuits diagnosed. Let me know if you need further assistance.

May 13, 2012 | 2002 Nissan Sentra

1 Answer

Headlamps not working, fuses o.k., bulbs ok, replaced switch ok 98 chevy cavalier w/ daytime running lights . 2 relays on harness between headlamps one is for fog lamps, not sure of the other , cannot get...


are your daytime running lamps working. if they are according to the schematic there are 4 relays, fog lamp, fog lamp cut off, isolation, and daytime running lamp; 2 fuses: right and left, that supply volts to the headlamps. it's a little confusing though, because these schematics might have some mistakes. anyway, it looks like the drl relay.grounds the headlamps when the drl control in the micro processor located in the instrument cluster senses the headlamps have been turned on. this trips the relay and 12vdc is supplied. the dlr might be bad. otherwise, i would think you have a hardwire or connector problem.

Mar 08, 2010 | 1998 Chevrolet Cavalier

1 Answer

Fog lamps dont work i check fuses and relay the switch shows the fog lamps are on


If you have not replaced the headlamp with HID, the next thing, are the high beams on ?

If you turn the high beams on, the indicator lamp on the main headlamp switch should go out.

Next thing would be to check the fog lamp relay in the fuse panel ( passenger side kick panel by the fuel inertia switch ).

The fog lamp relay is a half size ISO relay, you should be able to swap with the trailer tow parking lamp relay ( R201 ), to test with.

The fuse you checked is the F17, the fog lamp fuse for Relay R202, correct ?

Nov 26, 2009 | 2006 Ford F-150

1 Answer

How to replace fog light bulb on 2001 hyundai 300xg


Replaced from the back side. Two ways to do this. 1. move the wheel well liner partially out of the way to get to the bulb & connector.
2. Remove the headlamp assy above the fog lamp bulb you wish to replace (pass side is easier than the driver's side because of the engine intake ducting on that side)
b6ca2de.jpg ad1a4b8.jpg .

Mar 19, 2009 | 2001 Hyundai XG300

1 Answer

99vw jetta fuse keeps popin.help.


You have a short in the wiring. I would check at the headlight.

Aug 24, 2017 | 1999 Volkswagen Jetta

1 Answer

HOW TO REPLACE HEADLIGHTS ON 2000 CHRYSLER LHS


ATTN: NIKKICARROLL

here is how to replace the bulb in your vehicle


  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp.
  3. Remove the screws holding the headlamp module halves together.
  4. Separate the module halves.
  5. Disengage the wiring from the headlamp bulb.
  6. Remove the retaining ring from the back of the headlamp bulb.
  7. Pull the bulb from the lamp.
To install:
  1. Push the bulb into the lamp.
  2. Install the retaining ring to hold the bulb in the lamp.
  3. Engage the wire connector to the back of the headlamp bulb.
  4. Place the module into position on the vehicle.
  5. Install the screws to hold the module to the vehicle.
  6. Install the radiator closure panel sight shield.
  7. Check the headlamp alignment and operation.
88176gb1.gif Exploded view of the fog lamp with the bulb removed
Click to Enlarge

  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as needed to gain access to the headlamps.
  3. Remove the screws holding the headlamp module halves together.
  4. Separate the halves.
  5. Remove the fog lamp wire connector cover.
  6. Disconnect the wires from the fog lamp bulb.
  7. Disengage the retainer clip holding the bulb to the fog lamp.
  8. Remove the bulb from the fog lamp.
To install:
  1. Place the bulb into position in the fog lamp.
  2. Engage the retainer clip to hold the bulb to the fog lamp assembly.
  3. Attach the wire connectors to the fog lamp bulb.
  4. Install the fog lamp wires connector cover.
  5. Place the module halves together.
  6. Install the screws to hold the headlamp module halves together.
  7. Install the radiator closure panel sight shield.
  8. Verify the fog lamp operation and alignment

ATTN: WDSNEED1

Removal & Installation 88176g87.gif Remove the screws retaining the headlamp module to the mount adapter
Click to Enlarge

  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp fasteners.
  3. Remove the screws holding the headlamp module to the mount adapter.
  4. Separate the headlamp module from the mount adapter.
  5. Disengage the wiring from the headlamp and foglamp.
  6. Remove the headlamp from the vehicle.
To install:
  1. Attach the wires to the headlamp and foglamp assembly.
  2. Place the headlamp module into position on the mount adapter.
  3. Install the screws to hold the headlamp module to the mount adapter.
  4. Install the radiator closure panel sight shield.
  5. Check the headlamp alignment and operation.

Jul 28, 2008 | 1994 Chrysler New Yorker

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

80531 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...