Question about 2000 Acura TL

1 Answer

How do I ad fluid to the abs unit? - 2000 Acura TL

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 218 Answers

There is no way to add fluid to the actual ABS unit, you can only add fluid to the master cylinder. hope this helps

Posted on Jul 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No brake fluid coming out of hydraulic unit to rear wheel cylinders/


ABS unit may need a scan tool hooked to it to command the ABS motors to the home position so the fluid can flow to be bled.

Mar 31, 2016 | Cars & Trucks

1 Answer

Abs pump


abs LIGHT, brake system, may need fluid added, or system bleed, or both !

Mar 07, 2013 | Chevrolet Cobalt Cars & Trucks

1 Answer

Abs control module on honda cr-v 2007


ok about the abs is possible that the abs cable that goes the the brake caliper is not good.about the brake light check brake fluid level filled up also check the sensor on the brake fluid container also check any malfuntioning wire connection corosive plugs.about the ac check compressor ad freon in order to kick on check the relay or fuses or the compressor is no good

Jul 13, 2012 | 2007 Honda CR-V

1 Answer

My ABS light has been on for a while and today I hit the brakes and they turned spongy. Then I pushed the pedal some more and the brake pedal went right to the floor. Then the emergency light came on and I...


I hope you have enough sense to stop driving it and stop added brake fluid

Lets review:

ABS Light is on--You may have an ABS System failure,do we continue to drive it, no
But you did,you said awhile
Spongy brakes--normal,I don't think so
Brakes go to floor--how many things can cause that,maybe 2
Emergency Light--now were in big trouble,no brake fluid
Added Brake Fluid---no fluids are consumed on a motor vehicle
any fluid loss is from a leak and requires repair
You never top off any fluid,don't need to

You have an older vehicle with rusted out brake lines
You need to buy brake tubing,cut,bend,flair and fabricate new ones
No vehicle in history, ever had brake lines made for replacement

Dec 02, 2010 | 1994 Buick LeSabre

1 Answer

Line broke was leaking fluid then stopped leaking . no fluid comes out of abs unit on frame. is there a way to reset the abs unit to get fluid to rear brakes again


Replace the broken line then, you must bleed the entire brake system , each wheel works by itself on these cars, . Put the rearend in the air get the tires off and then find where the lines go into the ABS unit. Bleed fliud there first, then the individual wheel cylinders in the rear. after you bleed the system, check to make sure the brake system is balanced.

Oct 19, 2010 | Ford Ranger Cars & Trucks

1 Answer

The refittal of abs brake central unit Audi Avant A 6, -99, 1.8 T


If it's like my 2000 Passat, remove drivers front tire, remove the plastic wheel well ( about 10 screws) this big peice comes off giving you access to the windsheild washer fluid holder.

Nov 24, 2009 | 1999 Audi A6

2 Answers

Brake fluid contamination--stucking brake--driver's side


this is a stuck brake caliper piston not fluid contamination

Jul 02, 2009 | 2004 Lexus ES 330

2 Answers

ABS and BRAKE light at the same time


push the pedal and see if it goes to the floor slowly or fast, if so,some thing like this i would lay on the ground in the back and have some one push the pedlal and hold it, look for fluid, like wet spot near the wheels first ( i have seen wheel cylinder go bad but not leak alot at one time so keep that in mind too) and make your way to the front on the driver side inside of the fram.i dont think its the master cylinder but see if you can see a wet spot at the bottom of the master and the booster( i seen masters not leak as will )

leaks will make the ABS lite come on

Apr 11, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

95 accord abs system making noise


ur going to have to replace the abs modulator and accumulator and bleed the system ..

Mar 15, 2009 | 1995 Honda Accord

Not finding what you are looking for?
2000 Acura TL Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...