Question about 1999 Ford Explorer

1 Answer

Clutcth bearing what are the sign of going out

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,982 Answers

Generally that bearing will be noisy with very light pressure on the clutch pedal. It will go like that for a while, getting progressively noisier.

Posted on Jul 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My engine has a noise and oil sign is displayed and it does not go away although there is enough oil what it could be?


Bad oil pump? Bad bearings? Bad sender unit, but with bad noise probably the engine needs overhaul or replacement.

Jul 14, 2016 | 2007 Ford Bantam 1.3i

1 Answer

My 2002 focus se has a rattling in neutral wen i let off the clutch not wen i push clutch in


That sound is the "through-out bearing", and the rattle can be normal, or a sign that the bearing is going bad. It's a bad habit to sit at a red light with your foot on the clutch, that's what wears a through-out bearing out.
To replace this bearing, you need to remove the clutch and pressure plate. Perhaps time to replace?

Nov 24, 2015 | Cars & Trucks

1 Answer

How do i reset the abs light on my dashbord manually since i have repaired the cause of it


Don't know what kind of vehicle u have. 1: drive it for a while, should go off. 2: make sure all wheel bearings are not leaking grease onto abs sensor( sign wheel bearing is on its way out) 3: check is all plugs to the wheel bearings are in and wires are not chaffed. 4 bring it to garage and get reset.

Oct 27, 2014 | Cars & Trucks

1 Answer

Im trying to install a push button for my horn because i dont have a wheel puller. the horn wires re green and black but not sure if they change towards the coloumn. Also i dont know what fuse is for


BRAD: LOOK UNDER HOOD SEE IF YOU CAN FIND THE HORNS THEY SOULD BE IN RIGHT-LEFT FENDERS PULL THE WIRES OFF THERE SOULD BE A PLUS + SIGN AND - GROUND SIGN TAKE A WIRE BEAR BOTH ENDS HOOK ONE END TO HORN-N-OTHER END TO SOMETHING METAL UNDER HOOD ON THE GROUND SIDE ON THE OTHER SIDE THE +PLUS SIDE GET ON WIRE LONG ENUFF TO GO FROM HORN TO INSIDE CAB BEAR BOTH ENDS HOOK TO HORN BUTTON ON OTHER SIDE OF BUTTON PUT OTHER WIRE BEARED AT BOTH ENDS HOOK ONE END OF WIRE TO BUTTON-N-OTHER END TO A FUSE IN FUSE BOX IT SOULD BE ON DRIVERS SIDE OF DAS HOPE THIS HELPED YOU SIGNED PHIL

Mar 20, 2014 | 1997 Chevrolet S-10 Pickup

1 Answer

06 Elantra squeaking/rubbing front wheel


if your car is front wheel drive it could be your cvs that go to the trans,do you have the orginal tires on it or did you put bigger ones ? didyou do any changes/ then this noise started.thats the best I can do without me looking at it.

Aug 03, 2017 | 2006 Hyundai Elantra 2.0

1 Answer

Knocking noise just started. Gets worse when accelerating. Seems to go away at certain rpm.Not sure what it could be?


Worn wrist pin or worn connecting rob bearing, regardless it a sign or worn internal engine bearings. Try adding some Lucas engine oil additive and see if the knocking goes away. If it does then it's your connecting rod bearing and if it's still there. Then it's going to be a worn wrist pin and will need to be replaced before you loose the engine from a broken piston.

Thank you for using fixya and good luck

Oct 21, 2010 | 2001 Honda Civic

1 Answer

I have a loud rattling underneath front end, i have a 94 jeep grand cherokee laredo the rattling doesnt start until your moving forward and gets louder the faster you go. what could it be, i was thinking...


ok first look at the bearing see if you see oil around it wheres its leaking this there sign before going out and then at the u joint check and see if it is leaking as well this should tell you which one and it will be oil around the bearing not like gushing out fluid just a little bit hope this helps

Sep 14, 2010 | 1994 Jeep Grand Cherokee

1 Answer

1995 ford ranger wont go into gear grinds trying to go into reverse.


This is sign of a bad thrst bearing, try toadjust the clutch if not working, replace clutch, thrust bearing and pressure plate.

Jul 18, 2009 | 1998 Ford Ranger SuperCab

Not finding what you are looking for?
1999 Ford Explorer Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...