Question about 1994 Nissan Pickup

1 Answer

How do you remove the tail light assembly to replace a bulb?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 146 Answers

Inside the truck bed there are two bolts behind the tail light. You will need a 10mm socket to remove them. Remove them and the tail light assembly comes out and then twist the bulb connector and the then you can change the bulb.

Posted on Jul 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace left rear brake light bulb


1) Open trunk
2) Remove small round plastic access panel with a flat tip screw driver by prying open
3) Remove flat tip screw holding tail light assembly
4) Remove tail light assembly by pulling outward, careful not to break plastic guide/nub
5) Disconnect wiring connectors
6) Remove plastic housing access plate on back of tail light assembly by twisting/turning tabs until they click and then lift access plate from tail light assembly
7) When viewing the the bulbs, the turn signal bulb is the bottom left bulb
8) Install in reverse order, ensuring tail light seal seats properly during installation

Oct 13, 2014 | 1999 Audi A4

1 Answer

2002 GMC Yukon XL brake light replacement


Hello Weaver124!
Open the tailgate(s) completely and you'll find two phillips-head screws on the inside edge of the tail light assembly. Take out those two screws (keep one hand on the assembly when you remove the last screw) and the whole tail light assembly will come off of the vehicle. On the back side of the tail light assembly, twist and remove the light bulb housing for the blown bulb. The bulbs themselves on some models vary in the manner in which they are removed: (1) If the base on the bottom of the bulb itself is a *round* brass base, press down on the bulb then twist it to remove it, or (2) If the base on the bottom of the bulb itself is *flat* plastic, pull the bulb straight out of the assembly. To replace the bulb, simply reverse the order. Best wishes!

Mar 12, 2011 | 2002 GMC Yukon XL

1 Answer

How do i replace the tail light bulb


Open the trunk, and pull back the carpet behind the tail light assembly-- you should see 3 different sets of wires going into the back of the tail light assembly. Pick the one you need to replace, and give it about a quarter turn counter-clockwise, and the bulb, harness, and wire can be pulled out of the tail light. Replace the burned out bulb in the socket, and reinstall the bulb just as you removed it.
If you have difficulty getting to the wiring harnesses to dislodge them from the tail light assembly, you can remove the tail light entirely by unscrewing the black plastic wingnuts that hold the tail light assembly in place. It may take a little bit of effort to get them started, but will allow you to see what you are doing a bit better.

Mar 04, 2011 | 2000 Lincoln Town Car

3 Answers

Tail lights do not work on a 2000 lexus rx 300 bulbs are fine, all other lights work fine


You may have a fried fuse. Look in your owners manual to find out which fuse it is in the fuse box diagram. If that is the problem make sure to use the same amperage fuse to replace the burned one with. I fried fuse is usually a sign that you have a short somewhere. But they can also fry for other reasons such as excess moisture somewhere. Sometimes they just burn from age and fatigue. It may solve it to just replace the fuse, but if there really is a short, the new fuse will fry too.

Dec 29, 2010 | 2000 Lexus RX 300

1 Answer

How to replace LR2 Third Brake Light


The Freelander is Land Rover's entry-level crossover SUV. Unlike other Land Rover vehicles that use a traditional "truck," body-on-frame chassis, the Freelander is built on a unibody, front-wheel drive car chassis. The Freelander is sometimes known in the U.S. as the "LR2."

1 Purchase replacement bulb P21/5W, available at most auto parts stores and at any Land Rover
dealer.

2 Turn off engine and open rear cargo door.

3 Remove the two Torx screws from the side of the tail light assembly. Carefully pull the assembly
away and unplug the electrical harness.

4 Turn the assembly over to access the bulb modules. There are three separate bulb modules; the
top module should be the brake light.

5 Rotate the bulb module counterclockwise to release it from the tail light assembly. Push the bulb
down (into the module) and turn it counterclockwise to remove it from the module.

6 Insert the new bulb into the bulb module. Carefully push the bulb down and turn it clockwise.
Reinsert the bulb module into the tail light assembly and turn it clockwise.

7 Reconnect the electrical harness to the tail light assembly. Remount the tail light assembly and
replace the Torx screws.


Dec 26, 2010 | Land Rover LR2

1 Answer

Change out a taillight


You want to change the tail light bulb?

The process for replacing tail light bulbs is the same in all models. If you have a burnt-out tail light bulb, you may need to replace the brake light, the reverse light or the turn signal. The procedure to replace each of the bulbs is the same.



    Instructions

    1. Open the Hummer's rear swing gate. This will expose the edge of the vehicle's tail light assembly. You'll see two small Phillips head screws that hold the tail light assembly in place. Put on your gloves.

    2. Remove the two screws from the tail light assembly. Pull the tail light out and inspect the back for two bulbs. The top bulb is the brake light and turn signal. The bottom bulb is the reverse bulb. Determine which bulb you need to replace.

    3Rotate the bulb's socket counterclockwise to disconnect it. Unplug the bulb from its socket.

    4Push the replacement bulb into its socket firmly. Insert the socket back into the tail light. Turn it clockwise to secure it in place.

    5Place the tail light into its cradle. Hold it with one hand and replace the Phillips head screws with the other.

Dec 03, 2010 | 2008 Hummer H3

1 Answer

How to change break lights


Tail Lights
  1. Open the endgate or liftgate.

  2. Remove the screws that retain the tail lamp assembly to the vehicle.
    32085_blaz_g0151.gif

    Tail lamp assembly removal

  3. Rotate the bulb sockets 1/4turn counter-clockwise in order to remove the bulb sockets from the tail lamp assembly.

  4. Remove the bulbs from the sockets.

To install:

  1. Install the bulbs into the sockets.

  2. Install the bulb sockets to the tail lamp assembly by rotating the sockets1/4 turn clockwise.

  3. Install the tail lamp assembly to the vehicle.

  4. Install the screws that retain the tail lamp assembly to the vehicle. Tighten the screws to 17 inch lbs. (1.9 Nm).

Oct 23, 2010 | 2000 Oldsmobile Bravada

2 Answers

Having trouble fixing brake lights


Tail/Turn Signal Lamp Removal & Installation Cab/Chassis gm-06-00-1071.gif

To Remove:
  1. Disconnect lamp assembly electrical connector.
  2. Remove nuts and lamp assembly from bracket.
  3. Remove lens screws.
  4. Remove lens, gasket and bulb.
To Install:
  1. Install lamp assembly and nuts to bracket.
  2. Connect electrical connector.
  3. Install bulb, gasket and lens.
  4. Install lens screws.
Except Cab/Chassis gm-06-00-1075.gif

To Remove:
  1. Lower endgate.
  2. Remove 2 tail/turn signal lamp assembly retaining screws.
  3. Rotate tail/turn signal lamp assembly and remove from vehicle.
  4. Disconnect lamp assembly electrical connector.
  5. Remove bulbs by pulling straight out of bases.
To Install:
  1. Install bulbs by pushing straight into bases.
  2. Connect electrical connector.
  3. Install tail/turn signal lamp assembly to vehicle and secure with 2 screws.
prev.gif next.gif

Oct 13, 2010 | 1997 GMC Sierra

2 Answers

How do I replace a burned out backup light on a 1998 cheverolet silverado c-1500 pickup truck?


Removal & Installation Cab/Chassis gm-06-00-1071.gif

To Remove:
  1. Disconnect lamp assembly electrical connector.
  2. Remove nuts and lamp assembly from bracket.
  3. Remove lens screws.
  4. Remove lens, gasket and bulb.
To Install:
  1. Install lamp assembly and nuts to bracket.
  2. Connect electrical connector.
  3. Install bulb, gasket and lens.
  4. Install lens screws.
Except Cab/Chassis gm-06-00-1075.gif

To Remove:
  1. Lower endgate.
  2. Remove 2 tail/turn signal lamp assembly retaining screws.
  3. Rotate tail/turn signal lamp assembly and remove from vehicle.
  4. Disconnect lamp assembly electrical connector.
  5. Remove bulbs by pulling straight out of bases.
To Install:
  1. Install bulbs by pushing straight into bases.
  2. Connect electrical connector.
  3. Install tail/turn signal lamp assembly to vehicle and secure with 2 screws.
prev.gif next.gif

Jul 17, 2010 | 1998 Chevrolet C1500

1 Answer

How do i replace the tail light bulb?


to replace the GM tail light bulb, you will drop down the tail gate and you will notice 2 screws on the tail light assembly, you will remove those 2 screws with the proper screw driver, once you do that the whole tail light assembly will come off, then you will see onother 2 screws holding the light panel to the tail light assembly, or brackets holding the light panel to the tail light assembly remove either or and you will have access to the three bulbs on that light panel, replace the burnt one and follow the same intrunctions to put back.

Apr 06, 2010 | 2005 GMC Canyon

Not finding what you are looking for?
1994 Nissan Pickup Logo

290 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...