Question about 2000 Mercury Sable

1 Answer

Where is the camshaft sensor located on a 2000 mercury sable

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 659 Answers

It is located on top of the engine on drivers side right below throttlebody area

Posted on Jul 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 Sable engine change


check the location of the cam position sensor. if they are in the same place ,then use all the sensors from the old motor

Jan 09, 2013 | 2003 Mercury Sable

1 Answer

Will a 3.0L DOHC Duratec 30 V6 from a 2000 Sable fit in a 2003 Sable?


how do i change my DPFE sensor on my mercury sable 2000 .

Jan 09, 2013 | 2003 Mercury Sable

1 Answer

My 2000 sable turns over but wont start engine light on but pulls no codes


i have a 2000 mercury sable wont start. its getting gas, but not getting fire. i change the crank sensor an the coil pack but still no spark from the coil

Sep 15, 2012 | 2000 Mercury Sable

2 Answers

I need to change my turning signal fuse in a 2000 mercury sable but cannot locate the fuse relay. Can anyone tell me where it is located. I have no turning signals right now!


For 2000 Mercury Sable 3.0L EFI DOHC 6cyl the Flasher is located on front seating area, driver side, under dash, mounted in junction block.

zjlimited_253.jpg

Passenger compartment fuse panel
The fuse panel is located below and to the left of the steering wheel by the brake pedal. Remove the panel cover to access the fuses. To remove a fuse use the fuse puller tool provided on the fuse panel cover. I suggtes check the next positions...

zjlimited_254.jpg


zjlimited_255.jpg

Hope this helps (remember to rate and comment this).

Dec 16, 2010 | 2000 Mercury Sable

1 Answer

No oil pressure, camshaft position sensor error,


Yes, the sensor is in small housing the goes in the hole where the distributor used to go. That also drives the oil pump so don't drive it you'll ruin the engine. It's located down under the throttle body, near transmission end of the engine.

Jan 04, 2010 | 1997 Mercury Sable

1 Answer

Location of the camshaft position sensor in a 2004 mercury sable


it is located on top of the engine right below the air inlet tube at the base of the intake it is a black sensor on top of a silver housing where the distributor would normally be

May 01, 2009 | Mercury Sable Cars & Trucks

1 Answer

Locating and replacing a camshaft sensor in a 2005 dodge neon


this is a very very simple procedure. you do not need pics. there is a sensor located at the end of the engine on the far side from the belts. at the top. it has a plug with two wires in it. just remove the two 10mm bolts un hook the plug and reverse the process to reinstall. if you have a factory intake you may have to remove it to access this sensor. just the intake tube.

Apr 18, 2009 | 1996 Mercury Sable

1 Answer

1997 mercury sable 3.0


Look at the back of engine near tranny and you will see what looks like half a distributor without a distributor cap. The camshaft position sensor is mounted on top.
http://i253.photobucket.com/albums/hh43/chuck943/camshaftpostionsensor.gif

Mar 21, 2009 | 1997 Mercury Sable

1 Answer

1997 mercury sable camshaft sensor replacement


do you have 3.L 2v or 4 valve?

3.0L (2V) Engine
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Syncro Positioning Tool T95T-12200-A
svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Prior to removal of the camshaft position sensor (CMP sensor) (12126), set cylinder No.1 to zero degrees top dead center (TDC) of compression stroke. Note the position of the camshaft position sensor electrical connector. The installation procedure requires that the connector be located in the same position.
Removal
  1. Disconnect battery ground cable. Refer to Section 14-01 .
  1. Disconnect engine control sensor wiring connector from camshaft position sensor.
  1. Remove camshaft position sensor retaining screws and camshaft position sensor from camshaft position sensor housing.
  1. If removing camshaft position sensor housing from the cylinder blocks (6010), proceed with Removal Step 5. If not removing camshaft position sensor housing, proceed to installation Step 6.
  1. Remove hold-down clamp (12270) (bolt and washer assembly).
  1. Remove camshaft position sensor housing from cylinder blocks.
Installation
  1. svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: A special service tool such as Syncro Positioning Tool T95T-12200-A must be used to position the synchronizer assembly prior to installation of the camshaft position sensor. Failure to follow this procedure will result in improper camshaft position sensor alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage.
    Attach Syncro Positioning Tool T95T-12200-A as follows:
    1. Engage camshaft position sensor housing vane into the radial slot of the tool.
    1. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing.
  1. Pre-lubricate synchronizer gear with engine oil meeting Ford specification ESE-M2C123-A prior to assembly.
  1. Install camshaft position sensor housing so that drive gear engagement occurs. Locate camshaft position sensor electrical connector in the pre-removal position.
  1. Install hold-down clamp (washer and bolt) and tighten bolt to 19-30 Nm (14-22 lb-ft).
  1. Remove Syncro Positioning Tool T95T-12200-A.
  1. svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If camshaft position sensor electrical connector is not positioned properly, DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1.
    Install camshaft position sensor and retaining screws. Tighten screws to 1.5-4.0 Nm (14-35 lb-in).
  1. Connect engine control sensor wiring connector to camshaft position sensor.
  1. Connect battery ground cable.

Feb 22, 2009 | 1997 Mercury Sable

2 Answers

DPFE Sensor with codes PO401 And PO402


The DPFE is located near the EGR valve, it has 2 very thick silicone rubber hoses connected to it that come off the exhaust. It is rectangular and about 1/2 the size of a pack of smokes

Nov 12, 2008 | 2001 Mercury Sable

Not finding what you are looking for?
2000 Mercury Sable Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

fordexpert

Level 3 Expert

5471 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...