Question about Cars & Trucks

Open Question

Daelim VJF 250 - Check engine light blink 2 times then pause for 2 seconds.

I have a Daelim 250 VJF, when I switch on (Before engine start) the "Check Engine" light blinks 2 times and pause for 2 second. after I start the engine, it will work 2000RPM for one second then it works on 1000RPM for one second! the engine do this action for about 10 minute. the engine works for 5-10 minutes with lighting "check engine" light, after that if I switch off the engine and switch it on again, the "check engine" doesn't blink any more! and engine works fine! but if the engine works for 3-4 minute the "check engine" lights again! first time I changed the battery but the problem didn't fix. for second time I changed "Stepper Motor" but the problem didn't fix! what is the problem?! can you help me please? what does "Check Engine" light blinks means?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 19 Answers

SOURCE: check engine light blinks

i believe there is a guide in a haynes manual for your truck maybe you can try and get one and see.

Posted on May 21, 2009

Murphybanton
  • 2004 Answers

SOURCE: check engine light flashing a code. what does this mean

Please visit http://www.troublecodes.net/neon/

for clarification of your error code. But I strongly believe you fixed a low rated fuel pump.

also from your explanation you got code 55 which means no error code was recorded.

Rate this please.

Posted on May 29, 2009

  • 373 Answers

SOURCE: check engine light blinking 10 times

The pcm (powertrain control module ) is telling you it has a set code in the memory. Take the car to a parts place like (auto zone ) and have them to run a scam on the pcm for a trouble code. Once you have done that then you will be able to correct the problem. Hope this will help you.

Posted on May 27, 2010

  • 4 Answers

SOURCE: my check engine light blinks once, pause, twice,

If it's like some vehicles, each set of flashes of the check engine light represents a "code". So, the code your vehicle is giving you is 12345. You may check with a dealers service department or you may even be able to Google the code and you should be able to figure out what the problem is. Normally with your check engine light, it's more than likely an emission problem such as an oxygen sensor, loose gas cap, etc.

Posted on Jul 27, 2010

  • 1 Answer

SOURCE: 2000 Lincoln LS--Check engine light blinking/sputtering take off

Hey I have the same problem...i changed all 8coils and spark plugs. But now when I start the car sometimes it stutter(shaking), but once I pass 3rd gear it drives fine, the engine light was blinking, then stayed on..but I disconnect the battery to clear it. Would the car shake if your low on fuel?

Posted on Feb 03, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brainbox light comes up on the dashboard after driving few kilometres. I change it with another one but still the same problem. Toyota camry 1994 model.


Well, that's the check engine light I think. It is saying something is not normal. You can read out a trouble code to give you an idea of why it is on. Turn the ignition on, but engine stopped, and with a piece of wire bridge terminals TE1 and E1 in the service terminal box, at one rear corner of the engine compartment.

The check engine light will then blink. A steady blink 4 times per sec is "all normal".

Trouble codes are 2 digits, and these will be blinked - first digit - pause - second digit - repreat.

So the oxygen sensor fail code (a common one) is 21, and will show 2 blinks - pause - 1 blink - repeat.

There are 22 of these codes

Nov 18, 2011 | 1994 Toyota Camry

2 Answers

Toyaota Camry 1994 engine won't start, Engine light on


I would check for fuel,(pressure and injector pulse), spark, and compression, before checking any codes. Lack of any of these basics can result in codes, and then you waste alot of time chasing a symptom, instead of the actual problem.If more people followed basic diagnostics, which always come back to these three basics, rather than chasing codes first,they would find no starts much more quickly.

Nov 14, 2011 | 1994 Toyota Camry

2 Answers

Error codes for 1991 dodge spirit


Turn the key to run then off, back to run, then off, then to run and leave it on. The check engine light will be on and will then go off and then on again according to the codes the engine controler happens to have in it. If the check engine light was on when you stopped the car, then there is at least one code in the controler. The light will blink the codes like this.
Cycle the key three times and leave on on the third time. light on for about 3-4 seconds then goes out for about 2 seconds and then blinks one time and goes out for 3 seconds this is for the no.1. Then the light blinks 3 times and goes out for about 3-4 seconds. You have the code 13. You could have a whole string of codes in the controler memory. It could be something like this. key cycled 3 times, light on for 3-4 seconds, then blinks 1 time, pause, 3 times, longer pause, 2 times ,pause 4 times, longer pause, then 5 times, pause 5 times the goes out.
This is code ; 13,24, 55. code 55 isn't really a code. It just tells you it's the end of any codes the controller has.
If you disconnect the battery and hook it back, you will have code 13 which simply mean 'battery disconnect'. It will errace it's self after several starts if it's not disconnected again. If you cycle the key and you get 55, this means there are no codes recorded at this time.
You will allways get 55 when checking for codes wheather there are fault codes or not. The light on for a few second before the codes start flashing is only a bulb check. Some codes like 13 will not turn the check engine on, but but will leave a code for diagnostic purposes only. If you have the check engine light on and accellerate and the light begains to blink, then the controller is telling you that you have an engine miss and are running the chance of burning out you're catalatic converter if you continue driving. Sometimes its advised to disconnect the battery after you have recorded the codes.
This will erase all codes that are present but were generated by conditions that aren't pertanent to the present condition. and then the codes that come back are the real ones to address.
This link: http://minimopar.knizefamily.net/fault/index.html
Contains the entire list of Chrysler Engine Error Codes.


Mar 03, 2011 | 1991 Dodge Spirit

1 Answer

Service engine soon light is steady on and sometimes it blinks on and off, and the car falls dead randomly. My car is a 99 Dodge avenger SE 6 cylinder 2.5 Liter TKS


Cycle ignition switch from off to on 3 times in under 5 sec. the with the ign switch still on (3rd) cycle watch the check engine light flash on and off.There is a slight pause between the first and second number of the code and a 4 second pause between codes if there is more than one. With this information re ask your question







Jan 22, 2011 | 1999 Dodge Avenger

1 Answer

What is the codes for a 95 dodge caravan 3.0 v6 it's blinks twice


The 95 Caravan is great for giving you trouble codes. However they are two digit codes. There should be a blink sequence followed by a short pause then another blink sequence (example 2 blinks, short pause, 3 blinks... Then 5 blinks, pause, 5 blinks which means no more codes. Turn key from off to run three times and leave in run and watch check engine light to count blinks. Disconnecting negative terminal on battery for 30 seconds clears codes.

Sep 09, 2010 | 1995 Dodge Caravan

2 Answers

How to switch off engine service waring display


G'day mate i think you will find only the dealer can using a special little resistance tool which are normally to expensive for the average garage, take it for the service it new enough to look after

Apr 04, 2010 | 2009 Nissan Altima

3 Answers

Check engine light just came on 1993 toy camry


First you need to find out what the fault code is that is making the check engine light come on. To do this, locate the diagnostic connector under the hood. It will be a black rectangular connector approx 50mm X 25mm with Diagnostic written on the cover. Open the cover and on the inside of the cover will be a diagram of the connections and their different labels. Locate pins labelled TE1 and E1. Switch on the ignition switch without starting the engine and with a small jumper wire bridge between pin TE1 and pin E1. Observe the check engine light on the dash and you will notice that it will be flashing. Read the diagnosis code as indicated by the number of flashes that this light makes. Each code will be displayed by first blinking the first digit of the code, then a pause and blink the second digit of the code. For example, Code 52 (knock sensor signal) will flash 5 times, pause and then flash 2 times, then a longer pause before it goes onto the next fault code if there is another one. Once it has gone through all the stored fault codes it will go through the sequence again starting at the first fault code again. Due to the many different fault codes that can be obtained it would be better to post another question for the fault code obtained. Good luck!

Jan 06, 2010 | 1993 Toyota Camry V6

5 Answers

How do you read the codes on a 1988 jeep cherokee?


Take it to an AutoZone auto parts store, they will read them for free from your jeep's computer. Let me know how this turns out for you.


Benjamin

Jul 10, 2009 | Jeep Grand Cherokee Cars & Trucks

1 Answer

My 1987 turbo toyota supra will only rev up to 2500 rpm then cut out like a governer. when it drops to about 2000 rpm it will rev back up only to 2500 rpm. at an idle it runs rough


The throttle position sensor has an idle switch in it that tells the car's computer that the throttle is positioned at idle. If the idle switch sticks in the idle position, the computer will not allow the engine to rev more than 2500 rpm. In your case, I think the switch is stuck.

First, see if you can get the trouble codes to come up. Rig a jumper wire and jump between the "T" terminal and the "E1" terminal in the car's "Diagnostics" box. It is a small black box on the driver's side of the engine compartment near the battery. Open the lid and on the inside of the lid it has a map of the terminals.

Once you hook up the jumper wire, turn the ignition switch to on but do not start the car. If there are codes, the check engine light (orange) will blink the 2 digit code. It blinks the first digit, pauses, then blinks the second digit. The code for the throttle position sensor is code "41". That is, four blinks...pause...then one blink. If this code comes up, change the throttle position sensor. (If there are no codes, the check engine light will steadily blink once per second until you turn the key to off.) Don't forget to remove the jumper wire when you are finished.

Apr 10, 2009 | Toyota Tundra Cars & Trucks

1 Answer

How do i get the trouble codes off a 1989 mazda mpv?


http://img178.imageshack.us/img178/3331/obdikx3.jpg

The above link is to a diagram of your ALDL connector, all you need is a paper clip, straighten out the paper clip and insert one end into the diagnostic test pin and one in the system ground pin (terminals A & B).

Then put the key in the ignition and turn it to the on position but DO NOT start the engine. You will then see the check engine light flash. It will initially start by flashing once, then a pause and then flash twice and it will repeat this three times. That flash sequence indicates 12, which just means the system is operating. Its the flash sequences after that that will give you the code if any are stored.

For instance if it flashes twice, then pauses, then flashes four times, thats code 24. So any flash sequence you get after the initial 12 (flash once, pause, flash twice) you need write those down. Below is a list of diagnostic codes to tell you what the codes mean.

Code 12
1 flash, pause, 2 flashes
Diagnostic: This Code will flash whenever the diagnostic terminal is grounded with the ignition switch turned on and the engine is not running.

Code 13
1 flash, pause 3 flashes
Oxygen sensor voltage stays between 0.35 and 0.55 volts for 30 seconds when the TPS signal was above 0.55 volts. The engine had been running for at least 40 seconds with an engine temperature above 110° F.

Code 14
1 flash, pause, 4 flashes
Coolant temperature sensor signal indicates a temperature of over 284° F for 4 seconds after the engine had been running for at least 10 secondsCoolant Sensor Circuit (high temperature) If the engine is experiencing overheating problems, have those fixed before continuing. Check all wiring and connectors associated with the coolant temperature sensor. Replace the Coolant temperature sensor.

Code 15
1 flash, pause, 5 flashes
Coolant Sensor Circuit (low temperature) Coolant temperature sensor signal indicates a temperature colder than -36° F for at least 4 seconds after the engine had been running for 2 seconds. See above, then check wiring connections at the ECM

Code 16
1 flash, pause, 6 flashes
Charging system voltage was either below 9 volts or above 17 volts for 10 seconds. System High Voltage If the voltage is above 17.1 volts for more than 2 seconds, the Service Engine Soon light will illuminate. Have the charging system checked.

Code 17
1 flash, pause, 7 flashes
PCM did not detect any spark reference pulses within 240 fuel control reference pulses (80 crank revolutions) while engine was running below 1200 RPM. Spark Reference Circuit.

Code 21
2 flashes, pause, 1 flash
Throttle Position Sensor, TPS voltage was above 0.8 volts for 5 seconds when engine was running and air flow was less than 15 gm/sec, or the TPS voltage was over 4.8 volts at any time.

Code 22
2 flashes, pause, 2 flashes
Throttle Position Sensor check TPS adjustment. Replace the TPS sensor. TPS voltage was under 0.2 volts for 4 seconds when the ignition was on. Check for a sticking, or mis-adjusted throttle position sensor.

Code 23
2 flashes, pause, 3 flashes
Inlet air temperature sensor signal showed an air temperature of -29° F for 4 seconds. Manifold Air Temperature. Check the MAT sensor, wiring, and connectors for a possible open circuit. replace the MAT sensor.

Code 24
2 flashes, pause, 4 flashes
Vehicle speed sensor signal showed less than 3 MPH for 2 seconds when engine speed was greater than 3000 RPM and transmission has not been in park or neutral for more than 4 seconds. Or vehicle speed goes from above 18 MPH to 0 in less than 2 seconds without applying brake. This code can only appear when the vehicle is in motion, if it appears when the car is not in motion, ignore it. Check ECM connections, any other problems should be diagnosed by a qualified mechanic.

Code 25
2 flashes, pause, 5 flashes
Inlet air temperature sensor signal showed an air temperature of over 218° F for 5 seconds when vehicle speed was greater than 35 MPH. Check the voltage between the MAT sensor and the ECM. voltage should be above 4 volts.

Code 26
2 flashes, pause, 6 flashes
Quad-Driver sense voltage shows a low voltage when battery voltage should be present, or if the sense voltage shows battery voltage when a low voltage should be present for at least 5 seconds when the engine was running. Have the car checked by a dealer.

Code 27
2 flashes, pause, 7 flashes
2nd gear switch was closed or grounded for 10 seconds when vehicle was in 4th gear, or 2nd or 4th gear switch was open when engine was first started. Gear switch Diagnosis Have the car checked by a dealer.

Code 28
2 flashes, pause, 8 flashes
3rd gear switch was closed or grounded for 10 seconds when vehicle was in 4th gear, or 3rd or 4th gear switch was open when engine was first started.

Code 29
2 flashes, pause, 9 flashes
4th gear switch was closed or grounded for 10 seconds when vehicle was in 4th gear, or 4th gear switch was open when engine was first started.

Code 31
3 flashes, pause, 1 flash
PRNDL indicates a gear other than park or neutral for 13 seconds for 3 consecutive startups when ignition was on, engine was off and vehicle speed was 0. Or the PRNDL status indicators (A, B, C, P) showed an incorrect combination of Lo and Hi for more than 10 seconds.
Check all connectors, and for a faulty switch.

Code 32
3 flashes, pause 2 flashes
EGR System Check vacuum hoses and connections for leaks and restrictions. Replace the EGR solenoid or valve.

Code 33
3 flashes, pause, 3 flashes
MAF Sensor Have the mass air flow sensor replaced.

Code 34
3 flashes, pause, 4 flashes
There was no MAF signal for over 4 seconds while engine was running. Check for loose or damaged air duct, misadjusted minimum idle speed and cacuum leaks. Inspect the MAF sensor and the electrical connections.

Code 38
3 flashes, pause, 8 flashes
The Torque Converter Clutch portion of the brake switch was open and caused the TCC to be inoperative, adjust OR replace switch.

Code 39
3 flashes, pause, 9 flashes
Torque Converter Clutch Check ECM connections, check for faulty Torque Conver Clutch solenoid.

Code 41
3 flashes, pause, 1 flash
Cam sensor signal was not received by PCM for the last 5 seconds while engine was running. Check for faulty connections, or a faulty cam sensor. Maybe also indicate a problem with the vehicle's timing chain.

Code 42
4 flashes, pause, 2 flashes
The Electronic Spark Timing (EST) signal did not change when the ECM applied bypass voltage to the ignition module. Check for faulty connections, or a faulty ignition module.

Code 43
4 flashes, pause, 3 flashes
Knock sensor signal was either above 3.5 volts or below 1.5 volts for at least 20 seconds. Check for a faulty knock sensor, or Mem-Cal.

Code 44
4 flashes, pause, 4 flashes
Oxygen sensor voltage was under 0.25 volts for up to 4 1/2 minutes of closed loop operation, lean exhaust. Check the ECM wiring connections. Check for vacuum leaks at the hoses and intake manifold gasket.

Code 45
4 flashes, pause, 5 flashes
Oxygen sensor voltage was over 0.75 volts for 2 minutes in closed loop operation with a throttle angle between 0.6 and 1.9 volts. Rich exhaust. Check the evaporative charcoal canister and its components for the presence of fuel.

Code 46
4 flashes, pause, 6 flashes
Power Steering pressure switch Check for faulty connections, or a faulty switch.

Code 48
4 flashes, pause 8 flashes
Misfire Diagnosis. Check the ignition and fuel systems.

Code 51
5 flashes, pause, 1 flash
Prom or Mem-Cal Make sure the MEM-Cal or prom is properly installed in the ECM. Replace Mem-Cal or prom.

Code 52
5 flashes, pause, 2 flashes
Cal-Pak Check the Cal-Pak to insure properation. replace the Cal-Pak.


Code 54
5 flashes, pause, 4 flashes
EGR #2 solenoid was out of range for 6 of 8 tests. 55 EGR #3 solenoid was out of range for 3 of 5 tests.

Code 55
5 flashes, pause, 5 flashes
ECM Check for faulty connections. Replace the ECM.

Code 56
5 flashes, pause, 6 flashes
Quad-driver voltage was incorrect for 5 seconds on the circuit connected to QDM "B".

Code 57
5 flashes, pause, 7 flashes
Boost control solenoid did not open bypass valve causing engine torque to be too high.

Code 63
6 flashes, pause, 3 flashes
EGR flow was incorrect. EGR solenoid did not work properly. Have vehicle serviced by a dealer.

Code 64
6 flashes, pause, 4 flashes
Same as Code 63 EGR flow was incorrect. EGR solenoid did not work properly.

Code 65
6 flashes, pause, 5 flashes
Same as Code 63.

Dec 31, 2008 | 1989 Mazda MPV

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74843 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22082 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...