Question about 1988 Mazda B2200

Open Question

How do I replace the timing belt on my 93 Mazda B2200?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 37 Answers

SOURCE: 1991 mazda b2200- timing belt changed

The keyway and or the dot on the crank should be line at 12 oclock. You will see a point on the oil pump housing to go by. On the camshaft the pointer will be at 12 oclock also. Use the O on the camshaft to the top at mark. Be sure to look at the dist. roter to make sure that it is pointing at the #1 spark plug wire. I could get 180 out of time. If you do it right it should start up right away. then you can use a timing light to finish it.
Good Luck jerry1938@hotmail.com

Posted on Dec 13, 2008

Ad
motor1258
  • 6674 Answers

SOURCE: setting the timing on 1988 mazda B2200

All I can find at this time is 6 degrees BTDC @ 825 RPM in neutral, with park brake on obvioulsy.

Posted on Jan 31, 2009

rcampsr
  • 90 Answers

SOURCE: how to put on ignition switch on a '88 mazda b2200

If you mean actually replacing the ignition switch on the vehicle with a locking column. You need to do this. Dicconnect the battery, remove the lower panel of the dash if there is any. There is a bolt on the steering column near the fire wall on most vehicles, remove this bolt, it will release the spline on the steering column. Disconnect all wiring going to the column, unbolt the column from the dash support. Remove the column from the truck, on the ignition switch you will see where the two shear bolts screw the assembly together, center punch the center of each bolt. Now drill the bolt with a 1/8" drill about 1/4" to 3/8" deep. Now use a 3/8" drill and drill out the shear head until it comes off the bolt. You can now remove the switch assembly from the column. The new assembly should come with new shear off bolts so when you bolt it in place when tightned they will break off rendering it tamperproof again. Most vehicles are designed like this now to stop theft. Check the column for operation before reinstalling it in the reverse of above. You just want to make sure the key locks and unlocks the column before reinstalling in the vehicle. You may want to do this before you totally tighten the bolts and break them off permanently. Good luck, RAC

Posted on Apr 14, 2009

  • 1 Answer

SOURCE: 1989 mazda b2200 can not set timing

i have a 1988 mazda b2200 and i was sittin still runnin and it was a lil low in water and i was just ab to take off when it cut off. it made steam *** out the hood. the thing is its gettin eletric to the plugs and its gettin gas and i even tried a lil eather and its turnin over it just want crank. do u have a idea wat it could b? im thinkin it jump timeing.

Posted on Feb 25, 2010

ftw1952
  • 10319 Answers

SOURCE: how to replace a timing belt on a 2000 Mazda Protege

Here is a website that a free manual can be down loaded for your vehicle


http://ezinearticles.com/?Find-the-Free-Auto-Repair-Manual-You-Need-Online&id=92717

Posted on May 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1988 mazda b2200 gets spark from the coil but not the distributor


Remove the distributor cap, crank the engine is the distributor rotor turning? Then check the timing belt.

Oct 29, 2012 | 1988 Mazda B2200

1 Answer

I blew a headgasket in my b2200 and now its all back together it wont start


Do you have fuel pressure? do you have spark? is the timing belt on correctly?

Nov 29, 2010 | 1988 Mazda B2200

1 Answer

87 mazda b2200 turns over no start. is gettin fuel and i see the spark on the plug working. what am i missin?


the only other things are compression and timing, and incorrect cam timing can cause low or no compression. Is the timing belt moving, is the camshaft turning? I will bet your trouble is the timing belt.

Mar 11, 2010 | 1988 Mazda B2200

1 Answer

I need torque specs for the head on a 93 mazda b2200 2.2l 4 cylynder


First Step: 20 lb/ft
Sec Step: 40 lb/ft
3rd Step: 59-64 lb/ft

Feb 05, 2010 | 1988 Mazda B2200

1 Answer

Timing instructions


the timming should be set @ 6BTC you will need a timming light to check it.
You should go buy a manual from your local automotive store befor changing your timming belt
the site below will show you how to make sure you timming marks are right but it will not explain the removel or installation
http://www.mazdatruckin.com/B2200//B2200_Timing_Belt.html

Feb 25, 2009 | 1988 Mazda B2200

1 Answer

Setting the timing on 1988 mazda B2200


All I can find at this time is 6 degrees BTDC @ 825 RPM in neutral, with park brake on obvioulsy.

Jan 12, 2009 | 1988 Mazda B2200

1 Answer

.005 clearance between crankshaft and timing belt sprocket.


mazdas specs for the crank are .985 but alot of cranks are made with a tolerence of .005 so from the factory alot of cranks are .005 to big are alittle smaller but both are right alittle play wont hurt it

Dec 13, 2008 | 1988 Mazda B2200

2 Answers

1991 mazda b2200- timing belt changed


The keyway and or the dot on the crank should be line at 12 oclock. You will see a point on the oil pump housing to go by. On the camshaft the pointer will be at 12 oclock also. Use the O on the camshaft to the top at mark. Be sure to look at the dist. roter to make sure that it is pointing at the #1 spark plug wire. I could get 180 out of time. If you do it right it should start up right away. then you can use a timing light to finish it.
Good Luck jerry1938@hotmail.com

Nov 09, 2008 | 1988 Mazda B2200

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...